aspire NX30 Rover Kit Mod Built In Battery User Manual
- June 17, 2024
- aspire
Table of Contents
aspire NX30 Rover Kit Mod Built-In Battery
Product Information
Specifications
- Wattage Range: 1-30W
- Output Voltage Range: 0.50-8.00V
- Resistance Parameters: 0.2ohm to 3.5ohms
- Continuous Fire Time: 10 seconds
- Charging Port: Micro-USB
- Screen: OLED 0.86 inch
- Dimensions: 22.53660mm
- Battery Capacity: 2000mAh
- Battery: Built-in Lipo
Product Usage Instructions
Top Fill Instructions
- Unscrew and remove the top cap.
- Squirt E-Liquid into the tank.
- Re-attach the top cap to your tank and begin to vape.
Coil Installation
- Unscrew the top cap from the tank.
- Remove the Pyrex tube.
- Replace the atomizer with a new one.
NX30 Button Functions
- Click fire Button 5 times within 2 seconds to power the NX30 mod ON.
- Click fire Button 3 times quickly to go into or out of stealth mode.
- Press Fire Button + + to select between VW, VV, and Bypass modes.
- Press + and – buttons simultaneously for 2 seconds to rotate the screen.
- Press + / – to either Lock or Unlock the device.
- Press Fire Button + – to increase or decrease Wattage or Voltage.
Charging
Charging is via a Micro-USB charging port. The maximum charging current can reach up to 1A.
- Connect the mod to your charger. The screen will flash a battery icon.
- When the charge level reaches 4.2V or when it is fully charged, the mod will stop charging and the screen will turn off.
- The mod supports pass-through charging. To lengthen the life of the mod, we do not recommend vaping while charging (pass-through).
FAQ
Q: How do I fill the tank?
A: To fill the tank, unscrew and remove the top cap, squirt E-Liquid into
the tank, and re-attach the top cap.
Q: How do I install a new coil?
A: To install a new coil, unscrew the top cap from the tank, remove the
Pyrex tube, and replace the atomizer with a new one.
Q: How do I turn on the NX30 mod?
A: To turn on the NX30 mod, click the fire button 5 times within 2 seconds.
Q: Can I vape while charging?
A: While the mod supports pass-through charging, we do not recommend vaping
while charging to lengthen the life of the mod.
- 1* NX30 Mod
- 1* Nautilus X Tank
- 1* 1.8ohm U-Tech Coil (12-16W)
- 1* Replacement Pyrex
- 1* Micro-USB Cable
- 1* Lanyard
- 1* Warranty Card
- 1* User Manual
Top Fill Instructions
- Unscrew and remove the top cap.
- Squirt E-Liquid into the tank.
- Re-attach the top cap to your tank and begin to vape.
Coil Installation
- Unscrew the top cap from the tank
- Remove the Pyrex tube
- Replace the atomizer with a new one
WARNING
- When using a new atomizer, let the tank stand for 5 minutes, so the cotton can be saturated with juice before firing.
- Do not let the tank become completely empty. Refill the tank to avoid dry burning or damage to the atomizer.
Mod Appearance
Specifications
- Wattage Range: 1-30W
- Output Voltage Range: 0.50-8.00V
- Resistance Parameters: 0.2ohm to 3.5ohms
- Continuous Fire Time 10 seconds
- Charging Port: Micro-USB
- Screen: OLED 0.86 inch
- Dimensions: 22.53660mm
- Battery Capacity: 2000mah
- Battery: Built-in Lipo
NX30 Button Functions
Charging
- Charging is via a Micro-USB charging port. Maximum charging current can reach up to 1A.
- Connect the mod to your charger. The screen will flash a battery icon. When the charge level reaches 4.2V or when it is fully charged, the mod will stop charging and a screen will turn off.
- The mod supports pass-through charging. To lengthen the life of the mod, we do not recommend vaping while charging (pass-through).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>