gorenje 731800 Induction Hob Instructions
- June 3, 2024
- Gorenje
Table of Contents
731800 Induction Hob
INSTRUCTIONS FOR USE Induction hob
We thank you for your trust and the purchase of our appliance.
This detailed instruction manual is supplied to make the use of this product
easier. The instructions should allow you to learn about your new appliance as
quickly as possible.
Make sure you have received an undamaged appliance. If you do find transport
damage, please contact the seller from which you purchased the appliance, or
the regional warehouse from which it was supplied. The telephone number can be
found on the invoice or on the delivery note.
INFORMATION! Information, advice, tip, or recommendation
WARNING! Warning general danger
Contents
Safety precautions ……………………………………………………………………………………………………
4
Carfully read the instructions and save them for future reference ……………………………………..
4
Important notes and precautions ………………………………………………………………………………
7
Before connecting the appliance ………………………………………………………………………………….
7
Appliance description ……………………………………………………………………………………………….
8
Technical data ……………………………………………………………………………………………………………
8
Before first use …………………………………………………………………………………………………………..
8
Hob ………………………………………………………………………………………………………………………….
9
Operating the cooking hob ……………………………………………………………………………………….
12
Control unit ……………………………………………………………………………………………………………….
12
Switching on the hob …………………………………………………………………………………………………. 13
Switching on the cooking zones ………………………………………………………………………………….. 13
Changing the cooking zone settings …………………………………………………………………………….
13
Automatic rapid heating ……………………………………………………………………………………………… 13
Bridged cooking zone ………………………………………………………………………………………………… 14
Pan position recognition with automatic bridging of cooking zones …………………………………. 15
Power Boost ……………………………………………………………………………………………………………..
16
Overheat protection …………………………………………………………………………………………………… 16
Child lock / lock …………………………………………………………………………………………………………
17
Defrosting/reheating …………………………………………………………………………………………………..
17
Timer functions ………………………………………………………………………………………………………….
18
Pausing the cooking process Stop&Go (pause) …………………………………………………………..
19
Memory function ……………………………………………………………………………………………………….. 19
Automatic switch off …………………………………………………………………………………………………..
19
Switching off the cooking zone ……………………………………………………………………………………. 20
Residual heat indicator ……………………………………………………………………………………………….
20
Maximum cooking time ………………………………………………………………………………………………
20
Switching off the entire cooking hob …………………………………………………………………………….
20
User settings ……………………………………………………………………………………………………………
21
Cleaning and maintenance ……………………………………………………………………………………….
23
Troubleshooting table ………………………………………………………………………………………………
24
Noises during induction cooking ………………………………………………………………………………….
25
Installing a built-in hob …………………………………………………………………………………………….. 26
Installation procedure …………………………………………………………………………………………………
26
Air vents in the lower kitchen cabinet …………………………………………………………………………… 27
Flush-mount installation into the worktop ……………………………………………………………………..
28
Fitting the foam gasket ……………………………………………………………………………………………….
33
Connecting the cooking hob to the power mains ………………………………………………………
34
Connection diagram …………………………………………………………………………………………………..
34
Disposal …………………………………………………………………………………………………………………..
36
3
Safety precautions
Carfully read the instructions and save them for future reference This
appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
WARNING: The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements.
Children less than 8 years of age shall be kept away unless continuously
supervised.
Do not use steam cleaners or high-pressure cleaners to clean the appliance, as
this may result in an electric shock.
The appliance is not intended to be controlled by external timers or separate
remote controll system.
Means for disconnection must be incorporated in the fixed wiring in accordance
with the wiring rules.
4
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or. similarly qualified persons in order to avoid a hazard (only
for appliances supplied with connection cord).
WARNING: If the surface is cracked, switch off the appliance to avoid the
possibility of electric shock. Switch off all cooking zones using their
respective controls and remove the fuse or trip the main circuit breaker so
that the appliance is fully isolated from the power mains.
WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may
result in fire. NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire proof blanket.
WARNING: Danger of fire: do not store items on the cooking surfaces.
CAUTION: The cooking process has to be supervised. A short term cooking
process has to be supervised continuously.
CAUTION: This appliance is for cooking purposes only. It must not be used for
other purposes, for example room heating.
WARNING: Use only hob guards designed by the manufacturer of the cooking
appliance or indicated by the manufacturer of the appliance in the
instructions for use as suitable or hob guards incorporated in the appliance.
The use of inappropriate guards can cause accidents.
Metalic objects such as knives, forks, spoons and lids should not be placed on
the hob surface since they can get hot.
5
After use, switch off the hob element by its control and do not rely on the
pan detector. Appliance must be connected to fixed wiring which has
incorporated means of disconnection. Fixed wiring must be made in accordance
with the wiring rules.
6
Important notes and precautions
The appliance is intended for household use. Do not use it for any other
purpose, such as room heating, drying of pets or other animals, paper,
fabrics, herbs etc. As this may lead to injury or fire hazard. Appliance must
be connected to fixed wiring which has incorporated means of disconnection.
Fixed wiring must be made in accordance with the wiring rules. If another
electrical appliance is connected to an AC power socket near the appliance,
make sure the power cord does not come in to contact with hot cooking zones.
If the power cord is damaged, it should be replaced by the manufacturer or an
authorised service technician, in order to avoid hazard. Using the glass
ceramic hob as a storage area may result in scratches or other damage to it.
Never heat food in aluminium foil or in plastic containers on the cooking hob.
Such foil or containers may melt which can result in a fire or damage to the
cooking hob. Do not store temperature-sensitive items underneath the
appliance, such as cleaners or detergents, spray cans etc. Eventual mismatches
in colour shades between different appliances or components within a single
design line may occur due to various factors, such as different angles under
which the appliances are observed, different coloured backgrounds, materials,
and room illumination.
Before connecting the appliance
WARNING! Carefully read the instructions for use before connecting the
appliance. Repair or any warranty claim resulting from incorrect connection or
use of the appliance shall not be covered by the warranty.
7
Appliance description
INFORMATION! Appliance functions and equipment depend on the model.
1. Induction cooking zone rear left 2. Induction cooking zone rear right 3.
Induction cooking zone front left 4. Induction cooking zone front right 5.
Cooking hob control module
Technical data
(depending on the model)
A. Serial number B. Code C. Type D. Trademark E. Model F. Technical data G.
Compliance indications / symbols The rating plate with basic information on
the appliance is located on the bottom side of the cooking hob. Information on
appliance type and model can be found on the warranty sheet.
Before first use
If your hob has a glass ceramic surface, clean it with a damp cloth and some
washing-up liquid. Do not use aggressive cleaners, such as abrasive cleaners
that could cause scratches, abrasive dishwashing sponges, or stain removers.
During initial use, characteristic “new appliance smell” may appear; it will
gradually disappear.
8
Hob
Glass ceramic cooking surface
· The hob is resistant to temperature changes. · Do not use the glass ceramic
hob if it is cracked or broken. If a sharp object falls on the hob, the
hob may break. The consequences of such occurrence may be visible immediately
or only after a while. · If any visible crack appears in the hob, immediately
cut off the power supply to the appliance. · Make sure the cooking zone and
the cookware bottom is clean and dry. This will allow better conduction of
heat and prevent any damage to the heating surface. · Do not place empty
cookware on the cooking zone. The cooking zone may be damaged if you place an
empty pan onto it. Before placing a pan onto the cooking zone, wipe the pan
bottom dry to allow conduction of heat.
Cooking power levels
Cooking zone heating power can be set to 10 different levels (depending on the
model). The table
lists some examples of use for each level.
Cooking power level 0 1-2 3 4-5 6 7-8 9 P
Purpose
switched off , using the residual heat keeping the food warm, slow cooking of
smaller amounts (lowest setting) slow cooking (follow-up cooking after the
initial power boost) slow cooking (follow-up cooking) of large amounts, pan-
roasting of larger chunks searing and browning searing cooking of large
amounts, searing Power Boost setting for start of the cooking process; also
suitable for very large amounts of food
Energy saving tips
· When purchasing cookware, note that the diameter indicated on the pan
usually pertains to the upper edge or the lid, which is normally larger than
the diameter of the pan bottom.
· If a dish takes a long time to cook, use a pressure cooker. Make sure there
is always sufficient liquid in the pressure cooker. If an empty cooker is
placed on the cooking hob, it may overheat which in turn may lead to damage to
both the pot and the cooking zone.
· Whenever possible, close the pot or pan with a suitably sized lid. Use
cookware that fits the amount of food you are cooking. Cooking in a large
partly full pot will consume much more energy.
Induction cooking zone operating principle
· The cooking hob is fitted with highly efficient induction cooking zones. The
heat is generated directly in the bottom of the pan where it is needed the
most. This avoids any losses through the glass ceramic surface. Power
consumption is considerably lower than in conventional cooking zones with
radiation heaters.
· The glass ceramic cooking zone is not heated directly, but only indirectly
with the heat radiated back by the pan. After the cooking zone is switched
off, this residual heat is indicated by “H”.
9
· In induction cooking zones, heating is made possible by the induction coil installed under the glass ceramic surface. The coil induces a magnetic field which generates eddy currents in the bottom of a ferromagnetic pan, which in turn heats the pan.
WARNING! If sugar or food with high sugar content is spilled over a hot class
ceramic hob, immediately wipe the hob or remove the sugar with a scraper, even
if the cooking zone is still hot. This will prevent any damage to the class
ceramic surface.
Do not use detergents and other cleaners to clean a hot glass ceramic hob as
this could damage the surface.
Pan recognition
· Even if there is no pot or pan on the cooking zone or if the pan used has a
diameter that is smaller than the diameter of the cooking zone, there will be
no losses of energy.
· If the pan is much smaller than the cooking zone, there is a possibility
that it will not be recognized by the cooking zone. When the cooking
zone is activated, the sign and the selected power level will flash
alternately on the cooking power display. · If a smaller pan or pot is placed
on the cooking zone and it is recognized, the hob will only use as much power
as necessary given the pan size.
Induction cookware
· The induction will work correctly if you use suitable cookware. · Make sure
the pot or pan is in the middle of the cooking zone · Suitable cookware:
cookware made of steel, enamel-coated steel
pans, or cast iron pans. · Unsuitable cookware: alloy steel cookware with
copper or aluminium
bottom, and glass cookware. · The magnet test: Use a small magnet to check
whether the pan or
pot bottom is ferromagnetic. If the magnet sticks to the bottom of the pan,
then it is suitable for an induction cooker.
· When using a pressure cooker, keep an eye on it until the right pressure is
reached. First, set the cooking zone to maximum power; then, following the
pressure cooker manufacturer’s instructions, decrease the cooking power when
appropriate.
10
· Make sure there is enough liquid in the pressure cooker, or any other pot or
pan. Due to overheating, using an empty pot on the cooking zone may result in
damage to both the pot and the cooking zone.
· Some cookware does not have a fully ferromagnetic bottom. In such case, only
the magnetic part will heat up, while the rest of the bottom will remain cool.
· When using special cookware, observe the manufacturer’s instructions. · For
best cooking results, the ferromagnetic area on the cookware bottom should
match the size
of the cooking zone. If the cooking zone does not recognize the pan, try
placing it on a different cooking zone with a smaller diameter.
Cooking zone Ø 160 mm Ø 180 mm Ø 210 mm
190 x 210 mm Bridge (octa)
Minimum pan bottom diameter Ø 90 mm Ø 90 mm Ø 110 mm Ø 110 mm Ø 230 mm
Pan bottom has to be flat.
.
11
Operating the cooking hob
Control unit
(depending on the model)
A Hob on/off key A1 On/off/child lock indicator light B Lock/child lock C
Defrosting/reheating key C1 Defrosting indicator light C2 Reheating indicator
light C3 Pan position recognition with automatic bridging of cooking zones D
Cooking zone controls E Timer functions F Stop/go/memory function F1 Stop/go
and memory function indicator light H Power decrease key I Power increase key
J Power level displays J1 Decimal point indicating half-step power level for
the cooking zone K Program timer on/off L Program timer setting key () L1
Indicator light for active program timer on respective cooking zones M Program
timer setting key (+) N Time display Display units also work as keys for
adjusting the settings.
12
Switching on the hob
· Place the cookware onto the cooking hob. · Touch the on/off key (A) to
switch on the hob. · “0” will appear on all cooking zone displays. · A short
beep will be emitted.
INFORMATION! If no cooking zone is switched on in 10 seconds, the cooking hob
will power off.
Switching on the cooking zones
There are a total of either 9 or 17 different power levels that can be
selected. In case of 17 power levels, the dot on the display indicates a half
step (e.g. 8. means 8.5, depending on the model). · Touch the display unit for
the desired cooking zone. The selected
display unit will flash. · Use the (H) and (I) key to set the operating power
of the selected
cooking zone. · The cooking zone remains activated.
· If the hob does not recognize any pan on the selected cooking zone, the
symbol .appears. If you do not place a pan on the selected cooking zone within
2 minutes, the cooking zone will automatically switch off.
INFORMATION! Display units also work as keys for adjusting the settings.
Changing the cooking zone settings
Power level for the selected cooking zone can he adjusted using the (H) or (I)
key. To increase or decrease the power level faster, touch and hold the (H) or
(I) key.
Automatic rapid heating
All cooking zones are fitted with a special mechanism that sets the cooking
power to maximum at the start of the cooking process, regardless of the actual
power setting. After a while, the cooking zone power switches back to the
initially set level. Automatic rapid heating can be activated on every cooking
zone for any cooking power level except for level “9” and “P”. The auto rapid
heating function is suitable for dishes that have to be heated up and then
cooked for a longer period of time without the need for constant supervision.
The auto rapid heating function is suitable for dishes that have to be heated
up and then cooked for a longer period of time without the need for constant
supervision.
13
· The hob is switched on and a suitable pan is placed on one of the cooking
zones.
· Select the desired cooking zone that should be switched off (“0” appears on
the display unit).
· Press the relevant (H) or (I) key and hold it for approximately 3 seconds
until you hear a short beep. and will flash alternately on the display.
· Decrease the power to the level you wish to cook with after the automatic
rapid heating. · and selected power level will alternate on the power level
display. When the automatic rapid
heating time expires, the cooking zone automatically switches to the selected
level which will then be continuously displayed.
Automatic rapid heating table
Power level 1 1. 2 2. 3 3. 4 4. 5 5. 6 6. 7 7. 8 8. Automatic 40 60 70 100 120
150 180 220 260 300 430 400 120 150 195 200
rapid heating time
(sec)
Switching off the automatic rapid heating
If cooking power is decreased while the automatic rapid heating is activated,
the automatic rapid heating will be switched off for this cooking zone. The
auto function can be deactivated by selecting the relevant cooking zone and
decreasing the power level to “0”. Then, set the new power level.
Bridged cooking zone
(depending on the model) · Some models allow combining two cooking zones on
the left-hand side into a single large
connected cooking zone. Thus, a large oval pan or a griddle can be placed on
the combined cooking field. The pan has to be large enough to cover the
centres of the upper and lower cooking zone. · Maximum pan size: 40 x 25 cm.
For even heat distribution, we recommend using a heavy-bottom baking dish or
pan. During cooking, the dish or pan will heat up. Be careful to prevent
burns. · When placing the baking dish on the hob, make sure it does not cover
the control module.
INFORMATION! The pan should always cover the centre of the cooking zone!
14
Activating the bridged cooking zone
· Switch on the cooking hob by pressing the on/off sensor (A). ·
Simultaneously touch the two sensors and hold them for 3 seconds
(H). The sign will appear on the display unit for the rear field to indicate
that the two cooking zones are bridged. · Set the desired cooking power for
the bridged cooking zone.
· To change the bridged zone’s cooking power later on, use the (H) or (I) key for the lower cooking zone.
INFORMATION! The bridged cooking zone does not allow operation with a power boost; only power levels up to 9 are available.
Deactivating the bridged cooking zone
· Reduce the power of the bridged zone to 0. The bridged zone symbol will be
switched off.
· Both cooking zones will operate independently.
will disappear and heating
Pan position recognition with automatic bridging of cooking zones
(only with some models)
Pan position recognition is activated automatically 10 seconds after the
appliance is switched on. If there is a pan on the hob, the pan recognition
function will recognize its position and automatically bridge the cooking
zones depending on the size of the pan. Two adjacent cooking zones can be
merged into a single large cooking zone.
The sign will appear on the display unit for the rear field to indicate that
the two cooking zones are bridged.
· Set the desired cooking power for the bridged cooking zone. · To change the
bridged zone’s cooking power later on, use the (H)
or (I) key for the lower cooking zone.
INFORMATION! The bridged zone does not allow the power boost setting P.
Maximum available power level is 9.
Automatic pan position recognition can be activated at any time for 10 seconds
by pressing the pan recognition key (C3). Automatic pan recognition and
automatic cooking zone bridging are only effective on the cooking zones that
are not yet activated. Bridging of cooking zones can be deactivated by setting
the power level to “0”.
15
If there is no cookware on the cooking zone: · Switch on the hob. All cooking
zones are set to “0”. · Place the pan on any cooking zone. “0” starts to flash
on the cooking zone with the pan. Cooking
zone power can be adjusted by pressing the (H) or (I) keys for the respective
cooking zone. The function automatically bridges the cooking zones on the
left-hand side of the cooking hob, depending on the pan size. · You may
continue with the next pan, using the same procedure.
If the cookware is already on the cooking hob: · Switch on the cooking hob. ·
“‘0” will flash on the display unit of the cooking zone with the cookware on
it. Cooking zone power
can be adjusted by pressing the (H) or (I) keys for the respective cooking
zone. · If there are several pans on the cooking zone, the hob will
automatically detect all pans and “0”
will flash on display units of all zones on which a pan has been placed.
Cooking zone power can be adjusted by pressing the (H) or (I) keys for the
respective cooking zone; then continue with the next cooking zone. During the
first 10 seconds, automatic pan recognition can also be deactivated in user
settings using the “Au” parameter. See chapter User Settings. The function can
be used if the pan is already on the cooking hob or if the cooking hob is
empty.
Power Boost
(depending on the model) The function allows temporary cooking at maximum
power for up to 5 minutes. Then, the operating power is automatically reduced
to level 9. The function can be reactivated if the system is not overheated.
Activating the Power Boost
The hob is switched on and a suitable pan is placed on one of the cooking
zones. · Select the cooking zone. · Set the power level to 9, then press the
(I) key. · Symbol “P” will appear on the display. The function is activated.
Deactivating the Power Boost · Press the (H) key. Power boost will be
deactivated and operating power will return to level 9. · Power can be
decreased to desired level by pressing the (H) key.
Overheat protection
· The hob is fitted with a cooling fan which cools the electronic components
during cooking. The fan may operate for a while even after the end of the
cooking process.
16
· Induction cooking hob is also fitted with an overheating protector which
protects the electronic components from damage. The protector operates at
several levels. When the cooking zone temperature gets very high, the cooking
power is automatically reduced. If this does not suffice, the cooking zone
power continues to decrease, or the safety mechanisms switches off the cooking
zone completely. In such case, the display unit will read “”F2″”. When the
cooking hob is cooled down, its total power will be available again.
Child lock / lock
The cooking hob can be locked against unintended activation.
INFORMATION! The cooking hob has to be switched off or in the standby mode.
Locking the cooking hob controls Touch the on/off key and hold it for 3
seconds. “L” will appear on the cooking zone power displays. The cooking hob
is now locked. After 5 seconds, the cooking hob will automatically switch off
to standby mode.
Unlocking the cooking hob controls To unlock the cooking hob, proceed in the
same way as for locking it. The hob must be switched off. Touch the on/off key
and hold it for 3 seconds. “L” on the cooking zone power indicators will turn
to “0”. The cooking hob is now unlocked and ready for use.
INFORMATION! If the child lock function is activated in the user settings mode
(see chapter User Settings,), then the hob will be automatically locked every
time it is switched off.
INFORMATION! Activate the lock function before cleaning to prevent the hob
from being inadvertently switched on.
Defrosting/reheating
Press the (C) key to activate the defrosting/reheating function. In case of
defrosting, food temperature is maintained at around 42 °C; in case of
reheating, it is maintained at around 70 °C. Actual temperature may depend on
the type of cookware and amount of food.
Activating the defrosting function Press the (A) key to switch on the cooking
hob. Place the suitable pan on the selected cooking zone. Touch the (C) key
once; the indicator light (C1) will light up. Touch the (H) or (I) key for the
selected cooking zone. The symbol “u” will appear on the display.
17
Activating the reheating function
Press the (A) key to switch on the cooking hob. Place the suitable pan on the
selected cooking zone. Touch the (C) key twice; the indicator light (C2) will
light up. Touch the (H) or (I) key for the selected cooking zone. The symbol
“U” will appear on the display.
Deactivating the defrosting/reheating function
· Touch the (H) or (I) key for the selected cooking zone. · The cooking zone
will switch off and “0” will appear on the display unit.
Timer functions
This function allows two operating modes:
1. Setting the minute minder (countdown timer) function applies to the entire
cooking hob. With this function, the hob only beeps when the set time expires.
2. Program timer setting applies to the selected cooking zone. A separate
timer can be set for each cooking zone. When the set time expires, the cooking
zone is automatically switched off.
1 Countdown timer
The minute minder operates independently and it is not related to the
operation of any cooking zone. When the countdown timer is set, it will
continue to count down the time even if you switch off the cooking hob. The
minute minder can only be switched off when the cooking hob is on.
· Touch the (K) key to activate the timer. “00” will appear on the timer
display (O). Touch the (L) and (M) keys to set the time in the range from 1 to
99 minutes.
· After the set time expires, alarm will be activated; however, the cooking
zone will not be switched off.
· Switch off the alarm by touching any key; alternatively, it will switch off
automatically after a certain period of time.
· The minute minder function will remain activated even when the cooking hob
is switched off using the (A) key.
· During the last minute of countdown, remaining time will be displayed in
seconds.
2 Program timer
The program timer makes the cooking process easier by allowing you to see and
set the cooking time for the selected cooking zone. When the time set on the
timer expires, the cooking zone will automatically switch off and emit an
acoustic signal. Switch of the acoustic signal by touching any key;
alternatively, it will switch off automatically after a while. The switch-off
program timer can be set independently for all cooking zones. The program
timer may only be set for an active cooking zone.
· Touch the (K) key to activate the timer. “00” will appear on the timer
display (O). Touch the (K) sensor key again. The point (L1) for the relevant
cooking zone will start to flash.
· Touch the (L) and (M) keys to set the time in the range from 1 to 99
minutes.
18
· When the desired value is set, the countdown begins. The point (L1)
indicating which cooking zone the timer function is set for will continue to
flash.
· After the set time has expired, acoustic signal will be activated and the
cooking zone will be switched off. “00” will flash on the clock display.
· Switch off the alarm by touching any key; alternatively, it will switch off
automatically after a certain period of time.
Changing the set cooking time Remaining cooking time can be changed at any
time during cooking. Touch the power-off timer key (K) to select the timer
display for the desired cooking zone. The relevant indicator light (L1) will
flash. Touch the (L) or (M) key to set a new desired cooking time.
Displaying the remaining cooking time If several timer settings are activated,
remaining cooking time can be displayed by touching the (K) key.
Timer reset Select the desired timer display by pressing the (K) key (see
section Changing the set cooking time). The set timer will be displayed and
the indicator light for the relevant cooking zone will light up. Touch the (M)
key to set the value to “00”, or press the (L) and (M) keys simultaneously to
immediately reset the value to “00”.
Pausing the cooking process Stop&Go (pause)
The Stop&Go function can be used to pause the operation of the entire cooking
hob for up to 10 minutes. All cooking zones will temporarily switch off
automatically. This is convenient when, for example, the contents of one of
the pans has boiled over and you wish to clean the cooking hob.
Activating the Stop&Go function At least one cooking zone must be active.
Touch the Stop&Go function key (F). A short beep will be emitted. All settings
on display units start to flash; the pause key will be lit and it will also
flash. All program timer or minute minder settings are paused. All keys are
inactive, except for the pause (stop/go) key and the on/off key. If you do not
press any key within 10 minutes, all active cooking zones will switch off
automatically.
Deactivating the Stop&Go function Press the pause key again within 10 minutes.
The cooking hob continues to operate with the same settings as before the
pause.
Memory function
This function allows you to retrieve all cooking zone settings if the cooking
hob was accidentally switched off. However, this can only be done within five
seconds after the hob has been switched off.
Use the on/off key to switch the cooking hob back on within 5 seconds after it
has been switched off. The key (F) will flash on the display unit for 5
seconds. Within that time, touch this key and all settings that were active
just before the hob was switched off will be restored.
Automatic switch off
If the keys are activated for too long during cooking (e.g. due to spilt
liquid or an object placed over the sensor keys), all cooking zones will be
switched off after 10 seconds. The symbol will flash on the display. The
object should be removed, or the spilt liquid should be cleaned, from the
sensor keys within 2 minutes; otherwise, the cooking hob will switch off
automatically. The most recent settings can be restored with the memory
function using the Stop&Go key
19
Switching off the cooking zone
To switch off a cooking zone, use the relevant (H) key to set the value to
“0”. To quickly switch off the cooking zone, touch the relevant (H) and (I)
keys simultaneously. You will hear a short beep, and “0” will be displayed on
the display unit.
INFORMATION! If the power of all cooking zones is set to “0”, the cooking zone
will switch off automatically after 10 seconds.
Residual heat indicator
The glass ceramic hob is also fitted with a residual heat display, “H”. The
glass ceramic cooking zone is not heated directly, but only indirectly by the
heat radiated back by the pan. As long as the symbol “H” is lit up after the
hob has been switched off, there is residual heat in the cooking zone, which
can be used to keep the food warm or for defrosting. When the “H” sign
disappears, the cooking zone may still be hot. Be careful as there is danger
of burns!
Maximum cooking time
For safety, the cooking time for each cooking zone is restricted to a maximum
duration.
Maximum cooking time depends on the most recently set power level. If the
power level is not changed, the cooking zone will be switched off
automatically after the maximum cooking duration is reached.
Cooking power level U u 1 2 3 4 5 6 7 8 9 P*
Maximum operating
2
8 8 8 6 6 4 4 2 1,5 1,5 1,5
time (hours)
- After 5 minutes, the power level automatically decreases to 9; after 1.5 hours, the cooking zone is switched off.
Switching off the entire cooking hob
The cooking hob can be switched off at any time by touching the on/off key.
20
User settings
Setting the acoustic signal, automatic features, and lock parameters You can
adjust the volume of the acoustic signal, duration of acoustic alarm, total
maximum appliance power, and automatic lock settings. To activate the
parameter settings menu, press the pause key (F) when the appliance is
switched off, and hold it for 3 seconds. The first parameter “Uo” will appear
on the timer display, indicating the volume (loudness) of acoustic signals.
Use the timer key (K) to select the type of parameter. Press the timer setting
keys (L) and (M) to adjust the setting.
Uo: Acoustic signal and alarm volume (loudness) So: Acoustic alarm duration
Lo: Automatic lock Au: Automatic pan recognition Po: Total maximum power
The currently set parameter value will appear on the right-hand side cooking
zone power level displays. The value can be adjusted by pressing the (H) or
(I) keys for the cooking zone. All parameters can be confirmed and stored by
pressing the pause key (F) and holding it for 2 seconds. Then, a short beep
will be sounded. If you do not wish to store the new parameter settings, close
the user settings mode by pressing the on/off key.
Acoustic signal and alarm volume (loudness) “Uo” The following values can be
set: 00 on the display = off (does not apply to alarm and error acoustic
signal) 01 on the display = minimum volume 02 on the display = medium volume
03 on the display = maximum volume (default) A short acoustic signal will be
sounded upon every change, with the newly set volume. Acoustic alarm duration
“So” The following values can be set: 05 on the display = 5 seconds 1.0 on the
display = 1 minute 2.0 on the display = 2 minutes (default) Child safety lock
“Lo” If the automatic lock function is activated in the user settings mode,
the cooking hob will be automatically locked every time it is switched off. 00
on the display = off (default) 01 on the display = on
21
Pan position recognition with automatic cooking zone bridging “Au” If the
function of pan position recognition with automatic cooking zone bridging is
deactivated in the user settings mode, then the appliance will always be
operated manually (there will be no 10-second automatic pan recognition every
time the appliance is switched on). 0 on the display = off 1 on the display =
on (default) Total maximum power “Po” If the electric installation in your
home has different current limits, maximum power consumption of the cooking
hob can be reduced: 2.3 on the display unit = 2.3 kW = 10 A 2.8 on the display
unit = 2.8 kW = 12 A 3.0 on the display unit = 3.0 kW = 13 A 3.7 on the
display unit = 3.7 kW = 16 A 7.4 on the display unit = 7.4 kW = 2 x 16 A
(preset)
INFORMATION! If the power level is limited, the settings and the resulting
cooking power can be limited as well. The appliance is fitted with a power
management system that makes sure the effect of power limiting is minimal.
22
Cleaning and maintenance
After each use, wait for the glass ceramic surface to cool down and clean it.
Otherwise, all remaining impurities will burn onto the hot surface the next
time you use the hob. For regular maintenance of the glass ceramic hob, use
special care products that create a protective film on the surface to prevent
the dirt from sticking onto it. Before each use of the glass ceramic surface,
wipe off the dust or any other impurities that could scratch the surface, from
both the hob and the pan bottom.
INFORMATION! Steel wool, coarse cleaning sponges, and abrasive powders may
scratch the surface. The surface may also be damaged by aggressive spray
cleaners and unsuitable liquid cleaners.
Signage may be worn when using aggressive or abrasive cleaners or cookware
with coarse or damaged bottom. Use a damp soft cloth to remove minor
impurities. Then, wipe the surface dry. Remove water stains with a mild
solution of vinegar. However, do not use this solution to wipe the frame (only
with some models) as it may lose its sheen. Do not use aggressive spray
cleaners or descaling agents. Use special glass ceramic cleaners for stubborn
dirt. Observe the manufacturer’s instructions. Be sure to thoroughly remove
any cleaner residues after the cleaning process as they may damage the glass
ceramic surface when the cooking zones heat up. Remove stubborn and burnt
residues with a scraper. Be careful when handling the scraper to prevent
injury.
INFORMATION! The scraper is not included in appliance equipment.
INFORMATION! Only use the scraper when dirt cannot be removed with a wet cloth
or special cleaners for glass ceramic surfaces. Hold the scraper at the
correct angle (45° to 60°). Gently press the scraper against the glass and
slide it over the signage to remove the dirt. Make sure the plastic handle of
the scraper (in some models) does not come into contact with a hot cooking
zone.
INFORMATION! Do not press the scraper perpendicularly against the glass and do
not scratch the hob surface with its tip or blade.
Immediately remove any sugar or sugar-laden food from the glass ceramic hob
using a scraper, even if the hob is still hot, as sugar may permanently damage
the glass ceramic surface.
23
Troubleshooting table
During the warranty period, only a service center authorized by the
manufacturer may carry out any repairs.
Before making any repairs, make sure the appliance is disconnected from the
power mains either by removing the fuse or by disconnecting the power plug
from the wall outlet.
Any unauthorized repairs of the appliance may result in electric shock and
short circuit hazard; therefore, do not perform them. Leave such work to an
expert or a service technician.
In case of minor problems with appliance operation, check this manual to see
if you can fix the problem yourself.
If the appliance is not operating properly or at all due to inappropriate
operation or handling, a visit from a service technician shall not be free of
charge, even during the warranty period.
Save the instructions for future reference and pass them on to any subsequent
owners or users of the appliance.
Following is some advice on rectifying some common problems.
Problem/error The main fuse in your home trips often.
Continuous beep and display
F2 on the display
F on the display
Cause Call a service technician.
Water spilt over the sensor surface, or an object placed over the sensors.
Wipe the sensor surface. Cooking zone has overheated. Wait for the cooking
zone to cool down. This indicates that there has been an error during
operation.
If the problems persist despite observing the above advice, call an authorized
service technician. Repair or any warranty claim resulting from incorrect
connection or use of the appliance shall not be covered by the warranty. In
this case, the user will cover the cost of repair.
WARNING! Before the repair, disconnect the appliance from the power mains (by
removing the fuse or by removing the plug from the wall outlet).
24
Noises during induction cooking
Noises and sounds Cause
Solution
Inductiongenerated operating noise
Induction technology is based on the properties of some metals under electromagnetic effect. It results in so-called eddy currents that force the molecules to oscillate. These oscillations (vibrations) are transformed into heat. Depending on the type of metal, this could result in quiet noises.
This is normal and it is not a result of any malfunction.
Transformer-like buzz
Occurs when cooking at a high power level. The reason for this is the amount of energy transferred from the cooking hob to the pot or pan.
This noise will disappear or weaken when you reduce the power level.
Vibration and crackling of the cookware
This noise appears in cookware (pots or pans) made of different materials.
It results from vibrations along the adjacent surfaces of different material layers. This noise depends on the cookware. It can vary depending on the amount and type of food being cooked.
Fan noise
Correct operation of induction electronic components requires temperature control. Therefore, the cooking hob is fitted with a fan that cools the electronics depending on the sensed temperature.
The fan may operate even after the cooking hob has been switched off, if the temperature remains too high.
25
Installing a built-in hob
Installation procedure
· The worktop has to be completely level. · Suitably protect the edges of the
cut aperture. · Connect the cooking hob to the mains power supply (see
instructions for the connection of the
cooking hob to mains power supply). · Insert the hob into the cut aperture.
· Installation of the appliance into a kitchen worktop and its connection to
the power mains may only be performed by an adequately qualifi ed technician.
· Veneer or other fi nish of the piece of kitchen furniture into which the hob
is to be built in should be treated with heat resistant glue (100°C);
otherwise, the worktop fi nish may be discolored or deformed.
· Use of solid wood corner trims on worktops behind the cooking hob is only
allowed if the clearance between the trim and the cooking hob is no smaller
than indicated on the installation plans.
· Cooking hob is dimensioned to be built into the worktop over a piece of
kitchen furniture, with a width of 600 mm or more.
· Hanging, or wall-mounted kitchen elements should be installed high enough
not to interfere with the work process.
· The distance between the cooking hob and the kitchen hood should be no less
than indicated in the instructions for kitchen hood installation. The minimum
distance is 650 mm.
· The distance between the appliance edge and the adjacent tall kitchen
furniture element should amount to no less than 40 mm.
· Use of solid wood corner trims on worktops behind the cooking hob is only
allowed if the clearance between the trim and the cooking hob is no smaller
than indicated on the installation plans.
· Minimum distance between the built-in cooking hob and the rear wall is
indicated on the installation drawing.
30 cm
26
60 cm
80 cm
90cm
Air vents in the lower kitchen cabinet
INFORMATION! Normal operation of the induction cooking hob electronic
components requires sufficient air circulation.
Lower cabinet with a drawer · There must be an opening with a height of
no less than 140 mm along the entire width of the cabinet in the cabinet rear
wall. In addition, there should be an opening of at least 6 mm in the front
side, along the entire width of the cupboard. · A horizontal partition panel
should be installed underneath the cooking hob along its entire length. There
should be at least 10 mm of clearance between the lower end of the appliance
and the partition panel.
27
Adequate ventilation should be allowed from the rear side.
· The hob is fitted with a fan located in its lower part. If there is a drawer
below the kitchen cabinet, do not use it to store small objects or paper as
these could, if sucked into the fan, damage the fan and the cooling system.
Moreover, do not use the drawer to store aluminium foil or flammable
substances or liquids (such as sprays). Keep such substances away from the
cooking hob. Danger of explosion!
· There should be at least 20 mm of clearance between the contents of the
drawer and the fan inlet vents. Lower cabinet with an oven · Installing an
oven under the induction hob is possible for oven with a cooling fan. · Before
installing the oven, the kitchen cabinet rear wall has to be removed in the
area of the opening for installation. · In addition, there should be an
opening of at least 6 mm on the front side, along the entire width of the
cabinet. · If other appliances are installed under the induction cooking hob
we cannot guarantee their correct operation.
Flush-mount installation into the worktop
Appliances without faceted edges or decorative frames, are suitable for flush
mounting.
Installing the appliance The appliance may only be installed into a
temperature- and water-resistant countertop, such as a countertop made of
(natural) stone (marble, granite), or solid wood (the edges along the cut-out
have to be sealed). When installing into a countertop made of ceramics, wood,
or glass, a wooden sub-frame should be used. The frame is not supplied with
the appliance. The appliance may only be installed into a countertop made of
other materials after you have consulted the countertop manufacturer and
obtained his express approval. Internal dimension of the basic unit should be
at least equal to the internal cutout for the appliance. This will allow
simple removal of the appliance from the countertop. Attach sealing tape along
the perimeter of the bottom of the glass panel.
28
First, feed the power cord through the cutout. Place the appliance over the
centre of the cutout. Connect the appliance to the power mains (see
instructions for connecting the appliance). Before sealing the appliance, test
its operation. Seal the slot between the appliance and the countertop using a
silicone sealant. The silicone sealant used to seal the appliance has to be
temperature-resistant (to at least 160 °C). Smooth out the silicone sealant
using a suitable tool. Observe the instructions for use of the selected
silicone sealant. Do not switch on the appliance until the silicone sealant
has dried completely.
1. Silicone sealant 2. Sealing tape
WARNING! Pay particular attention to built-in dimensions with (natural) stone
countertops. When choosing the silicone sealant, observe the countertop
material and consult the countertop manufacturer. Use of inappropriate
silicone sealants can result in permanent discolouration of some parts.
Removing the built-in appliance
Disconnect the appliance from the powermains. Use a suitable tool to remove
the silicone gasket from the perimeter. Remove the appliance by pushing it
upwards from the bottom side.
WARNING! Do not attempt to remove the appliance from the upper side of
countertop.
WARNING! The service department shall only be responsible for repair and servicing of the cooking hob. Consult your specialized kitchen equipment dealer regarding the re-installation (of the flush-mount) cooking hob.
Stone countertop
1. Countertop 2. Appliance 3. Slot
Given the margin of error (tolerance) for the glass ceramic plate of the
appliance, and the cutout in the countertop, the slot is adjustable (min.2
mm).
Ceramic, wooden, or glass countertop
29
1. Countertop 2. Appliance 3. Slot 4. Wooden frame, thickness 16 mm Given the
margin of error (tolerance) for the glass ceramic plate of the appliance, and
the cut-out in the countertop, the slot is adjustable (min. 2mm). Install the
wooden frame 5.5mm below the upper edge of the countertop (see figure).
Observe the radii of glass edges (R10, R2) when making the cut-out.
30
GLASS
CUT-OUT
30 cm 60 cm
31
80 cm
90cm WARNING! If the oven is installed under a flush-mounted cooking hob, then
the worktop thickness should be at least 40 mm.
32
Fitting the foam gasket
INFORMATION! Some appliances come with the gasket already fitted! Before
installing the appliance into a kitchen worktop, attach the foam gasket
supplied with the appliance to the bottom side of the glass ceramic hob.
Remove the protective film from the gasket. Attach the gasket to the bottom
side of the glass (23 mm away from the edge). The gasket has to be applied
along the entire edge of the glass. The gasket may not overlap in the corners.
When fitting the gasket, make sure it is not damaged by or in contact with any
sharp objects.
WARNING! Do not install the appliance without the gasket!
33
Connecting the cooking hob to the power mains
· Power mains protection must conform to the relevant regulations. · Before
connecting the appliance, make sure the voltage specified on the rating plate
conforms to
the voltage of the power mains. · There should be a switching device in the
electrical installation that can disconnect all poles of
the appliance from the power mains, with a minimum clearance of 3 mm between
the contacts when open. Suitable devices include fuses, protective switches
etc. · The connection should be adjusted to the current and fuses. · After
installation, the parts carrying electrical current and insulated parts shall
be protected against contact.
WARNING! The appliance may only be connected by an authorised expert. False
connection can destroy parts of the appliance. In such case, there is no right
to warranty! Disconnect the appliance from the power mains before any repair
or maintenance operation.
Connection diagram
Jumpers (connecting bridges) are placed in the dedicated slot on the clamp.
The following may be used for connection:
· PVC insulated connection cables type H05 VV-F or H05V2V2-F with yellow-and-
green protective conductor, or other equivalent or superior cables.
· Exterior cable diameter should be at least 8.00 mm.
Normal connection:
2 phases, 1 neutral conductor (2 1N, 380-415 V~/50/60 Hz):
· Voltage between phases and neutral conductor is 220-240 V~. · Voltage
between the two phases is 380-415 V~. Install a jumper
between the terminals 45. The group should include at least two 16-ampere
fuses. Diameter of the power cord core should be at least 2.5 mm².
2 phases, 2 neutral conductors (2 2N, 220-240V~/50/60 Hz):
· Voltage between phases and neutral conductors is 220- 240 V~. · The group
(installation) should include at least two 16-ampere fuses.
Diameter of the power cord core should be at least 2.5 mm².
Special connection:
Single-phase connection (1 1N, 220-240 V~/50/60 Hz):
Voltage between phase and neutral conductor is 220-240 V~. Install jumpers
between the terminals 12 and 45. The group (installation) should be fitted
with a fuse of at least 32 A. Power cord core diameter should be at least 4
mm².
34
Run the power cord through a cord strain relief (clamp) which
False connection can destroy parts of the appliance. In such case, there is no
right to warranty.
WARNING! Before connecting the appliance, make sure the voltage specified on
the rating plate conforms to the voltage of the power mains. An expert should
check the actual voltage in your home (220- 240 V relative to N), using a
suitable meter!
Appliances with a width of 30 centimetres (two cooking zones) only allow
single-phase connection. The cross-sectional area of the power cord core
should be at least 1.5 mm²!
Power cord
(appliance without a power cord)
· The following may be used for connection: · PVC insulated connection cables
type H05
VV-F or H05V2V2-F with yellow-and-green protective conductor, or other
equivalent or superior cables. · Exterior cable diameter should be at least
8.00 mm. · Run the power cord through a cord strain relief (clamp) which
- Ferrules are not supplied.
INFORMATION! We recommend using electric wire ferrules (end terminals).
35
Disposal
Our product packaging is made of environmentally friendly materials that can
be recycled, disposed of, or destroyed without any hazard to the environment.
To this end, packaging materials are labelled appropriately.
The symbol on the product or its packaging indicates that the product should
not be treated as normal household waste. Take the product to an authorized
collection centre for waste electric and electronic equipment processing.
Correct disposal of the product will help prevent any negative effects on the
environment and health of people, which could occur in case of incorrect
product removal. For detailed information on removal and processing of the
product, please contact the relevant municipal body in charge of waste
management, your waste disposal service, or the store where you bought the
product.
We reserve the right to any changes and errors in the instructions for use.
36
718097-a1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>