scheppach HDA-14 100W Air Filtration System Instruction Manual

HDA-14 100W Air Filtration System
Instruction Manual

HDA-14 100W Air Filtration System

HDA-14

https://www.scheppach.com/de/service

|
---|---

Explanation of the symbols on the device
Symbols are used in this manual to draw your attention to potential hazards. The safety symbols and the accompanying explanations must be fully understood. The warnings themselves will not rectify a hazard and cannot replace proper accident prevention measures.

| Warning – read the instruction manual to reduce the risk of injury.
---|---
Attention!| We have marked points in these operating instructions that impact your safety with this symbol.

Introduction

Manufacturer:
Scheppach
Fabrication von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer
We hope your new tool brings you much enjoyment and success.
Note:
In accordance with the applicable product liability laws, the manufacturer of this device assumes no liability for damage to the device or caused by the device arising from:

• Improper handling,
• Non-compliance with the operating manual,
• Repairs carried out by third parties, Unauthorised specialists.
• Installing and replacing non-original spare parts
• Application other than specified
• Failure of the electrical system in the event of the electrical regulations and VDE provisions 0100, DIN 13 / VDE0113 not being observed

Please consider:
Read through the complete text in the operating manual before installing and commissioning the device. The operating manual is intended to help the user to become familiar with the machine and take advantage of its application possibilities in accordance with the recommendations.
The operating manual includes important instructions for safe, proper and economic operation of the device, for avoiding danger, for minimizing repair costs and downtimes, and for increasing the reliability and extending the service life of the device. In addition to the safety instructions in this operating manual, you must also observe the regulations applicable to the operation of the device in your country. Keep the operating manual package with the machine at all times and store it in a plastic cover to protect it from dirt and moisture. They must be read and carefully observed by all operating personnel before starting the work.
The device may only be used by personnel who have been trained to use it and who have been instructed with respect to the associated hazards. The required minimum age must be observed.
In addition to the safety instructions in this operating manual and the separate regulations of your country, the generally recognized technical rules relating to the operation of such machines must also be observed. We accept no liability  for accidents or damage that occur due to a failure to observe this manual and the safety instructions.

 Device description (Fig. 1)

1. Control panel
2. Rear cover
3. Clip bolt
4. Nut
5. Remote control
6. External filter
7. Internal filter

Scope of delivery

• Heavy-duty air filter
• External filter
• Internal filter
• Remote control
• 4x clip bolts
• 4x nuts
• 4x ceiling installation clip bolts
• 4x chains
• Operating manual

Proper use

Only use the air filter for wood dust. Materials such as liquids, metal chips, metal dust, screws, glass, plastic or stones can cause sparks and/or damage if they come into contact with any part of the machine. The machine may only be used in the intended manner. Any use beyond this is improper. The user/operator, not the manufacturer, is responsible for damages or injuries of any type resulting from this.
An element of the intended use is also the observance of the safety instructions, as well as the assembly instructions and operating information in the operating manual.
Persons who operate and maintain the machine must be familiar with it and must be informed about potential dangers.
In addition, the applicable accident prevention regulations must be strictly observed.
Other general occupational health and safety-related rules and regulations must be observed.
The liability of the manufacturer and resulting damages are excluded in the event of modifications of the ma- chine.
The machine may only be operated with original parts and original accessories from the manufacturer.
The safety, operating and maintenance specifications of the manufacturer, as well as the dimensions specified in the technical data, must be observed.
Please observe that our equipment was not designed with the intention of use for commercial or industrial purposes. We assume no guarantee if the equipment is used in commercial or industrial applications, or for equivalent work.

General safety information

WARNING! Read all safety information, instructions, illustrations and technical data for  this electric tool.

ATTENTION!
Ensure that no water, other liquids or ignitable cleaning agents get into the device in order to prevent a risk of electric shock and/or fire.
Do not clean the device with water, other liquids or (ignitable) cleaning agents in order to prevent a risk of electric shock and/or fire.
Do not spray any combustible materials such as insecticide or perfumes around the device.
Before connecting the machine to the power supply, check whether the voltage information on the device matches the local mains voltage. If the mains cable is defective, it may only be replaced by an authorised workshop or a similarly qualified person in order to avoid dangers.
Do not use the  device if the mains plug, mains cable or the device itself is defective or damaged.
Never touch the mains cable or the device with wet hands.
This device can be used by children from 8 years of age and by persons with reduced physical, sensory or mental capabilities or with a lack of experience or knowledge, if they are supervised during use or if they have received instruction  on the safe use of the device and have understood the risks.
Children may not play with the device. Cleaning and maintenance must not be carried out by children without supervision.
Make sure that air intakes/outlets are not covered. Therefore, do not place any objects on the air outlet or in front of the air intake.
Ensure that no foreign objects fall into the device through the air outlet.

ATTENTION!

The device is not a substitute for adequate ventilation, regular vacuuming or the use of a suction system.
If the socket used to operate the device is not connected properly, the device connector will become hot.
Make sure that a properly connected socket is used for the device.
Always use the device on a dry, stable, level and horizontal surface.
Make sure that there is a gap of at least 50 cm behind and to the sides of the device.
Do not place any objects on the device.
Do not sit or stand on the device. Injuries may occur if you sit or stand on the device. Do not place the device directly beneath an air conditioner so that no condensation can drop onto the device.
Before switching the device on, check whether all filters have been inserted correctly.
Only use original filters from the manufacturer which are specially suited for this device. Do not use any other filter. Burning of the filter can cause irreversible damage to health and/or endanger other lives. Do not use the filter as fuel or for other similar purposes.
Avoid bumping the device against solid objects (in particularly the air intake and outlet).
Always lift or move the device using the handles on the side of the device. Ensure that your fingers or other objects do not get inside the air intake or outlet in order to prevent injuries or damage to the device.
Do not use the device after using incense to protect against insects or in places where the air is polluted by oil residues, burning incense sticks or chemical vapours.
Do not use the device in the vicinity of gas-powered equipment, heaters or open fireplaces.
Always disconnect the device from the power supply after use and before cleaning, maintenance work or replacing the filter.
Do not use the device in rooms with high temperature fluctuations as these can cause condensation to form in the device interior. To avoid electronic interference, the device should be set up at least 2 meters away from other electrical devices that work with radio waves (e.g. televisions, radios and radio clocks).
The device is only intended for domestic use in normal operating conditions. Do not use it in humid environments or in rooms with a high ambient temperature, e.g. bathroom, toilet or kitchen. The device does not remove carbon monoxide (CO) or radon (Rn). It cannot be used as a safety device in the event of accidents involving combustion processes and hazardous chemicals.
If the device needs to be moved, first disconnect the device from the power supply.
Do not move the device by pulling the mains cable. Wash your hands after replacing the filter.

Safety instructions for handling batteries

1. Always make sure that the batteries are inserted
   with the correct polarity (+ and –), as indicated on
   the battery.

2. Do not short-circuit batteries.

3. Do not charge non-rechargeable batteries.

4. Do not overcharge batteries!

5. Do not mix old and new batteries or batteries of different types or manufacturers! Replace an entire set of batteries at the same time.

6. Immediately remove used batteries from the device and dispose of them properly! Do not dispose batteries with household waste. Defective or used batteries must be recycled according to Directive 2006/66 / EC. Give back batteries and / or the device has been offered to the collective facilities. About disposal facilities  you can inform by your municipal or city government.

7. Do not allow batteries to heat up!

8. Do not weld or solder directly on batteries!

9. Do not dismantle batteries!

10. Do not allow batteries to deform!

11. Do not throw batteries  into fire!

12. Keep batteries out of the reach of children.

13. Do not allow children to replace batteries without supervision!

14. Do not keep batteries near fire, ovens or other sources of heat. Do not use batteries in direct sunlight or store them in vehicles in hot weather.

15. Keep unused batteries in the original packaging and keep them away from metal objects. Do not mix unpacked batteries or toss them together! This can lead to a short-circuit of the battery and thus damage, burns or even the risk of fire.

16. Remove batteries from the equipment when it will not be used for an extended period of time, unless it is for emergencies!

17. NEVER handle batteries that have leaked without appropriate protection. If the leaked fluid comes into contact with your skin, the skin in this area should be rinsed off under running water immediately. Always prevent the fluid from coming into contact with the eyes and mouth. In the event of contact, please seek immediate medical attention.

18. Clean the battery contacts and corresponding contacts in the device prior to inserting the batteries.

Warning! This power tool generates an electromagnetic field during operation. This field can impair active or passive medical implants under certain conditions. In order to prevent the risk of serious or deadly injuries, we recommend that persons with medical implants consult with their physician and the manufacturer of the medical implant prior to operating the power tool.

Technical data

Filter performance
External filter| 5 µm
Internal filter| 1 µm
Air flow
High speed| 740 m³/h
Medium speed| 675 m³/h
Low speed| 600 m³/h
Automatic switch off times| 60 / 120 / 240 min
Weight| approx. 8 kg
Noise level| 50 / 55 / 60 dB

Technical changes reserved!

Noise and vibration
Warning: Noise can have serious effects on your health. If the machine noise exceeds 85 dB (A), please wear suitable hearing protection.

Unpacking

• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport damage. In the event of complaints the carrier must be informed immediately. Later claims will not be recognized.
• If possible, keep the packaging until the expiry of the warranty period.
• Familiarise yourself with the product by means of the operating instructions before using for the first time.
• With accessories as well as wearing parts and replacement parts use only original parts. Replacement parts can be obtained from your dealer.
• When ordering please provide our article number as well as type and year of manufacture for your equipment.

Attention!
The device and the packaging material are not children’s toys! Do not let children play with plastic bags, films or small parts! There is a danger of choking or suffocating!

Assembly

ATTENTION!
Always make sure the device is fully assembled before commissioning!

Installing the clip bolts (Fig. 2 – 3)

• Remove the transport lock screws (Fig. 2).
• Turn the nuts (4) over the entire length of the clip bolts (3).
• Screw the clip bolts (3) into the threaded holes and lock the nuts (4) against the top part of the housing (Fig. 2).
• Drill holes into the ceiling and mount the four ceiling mount clip bolts provided into the ceiling.
• Now hang the device onto the installation fastening hooks using the chains provided (Fig. 3).

NOTE: Fasten the device at least 2.13m above the floor.
Setting up the heavy-duty air filter
To ensure the device is operated properly through air circulation, make sure there is a gap of at least 50cm on both sides of the air intake and at least 10cm from the air outlet to the wall. Keep other electrical devices, such as radios and televisions, at least 1m from the device. Do not plug the mains plug into the same socket as one with radios, televisions or other electrical devices. This can cause the screen to flicker or interference noises.

• Long-term use in the same place can make the walls dirty.
• Ensure that the air intake and outlet are not covered in order to ensure optimal air circulation and maximum performance.

Start up

Attention!
Always make sure the device is fully assembled before commissioning!
Switching on/off (Fig. 4 – 5)

• Press the “ON/OFF” button on the remote control (5) or on the control panel (1) in order to switch the device on or off.

Timer function (Fig. 4 – 5)
The “TIME” button on the remote control (5) or on the control panel (1) controls the three different time settings:

• Press the “TIME” button once so that the device switches off automatically after one hour. (1H lamp lights up on the control panel.)
• Press the “TIME” button twice so that the device switches off automatically after two hours. (2H lamp lights up on the control panel.)
• Press the “TIME” button three-times so that the device switches off automatically after four hours. (4H lamp lights up on the control panel.)

Speed function (Fig. 4 – 5)
The “SPEED” button on the remote control (5) or on the control panel (1) controls the three different air speeds.

• Press the “SPEED” button once so that the device switches to the highest air speed.(HI lamp lights up on the control panel.)
• Press the “SPEED” button twice so that the device switches to the middle air speed.(MID button lights up on the control panel.)
• Press the “SPEED” button three-times so that the device switches to the slowest air speed.(LOW lamp lights up on the control panel.)

Inserting and changing batteries in the remote control

• Remove the battery compartment cover located on the bottom of the remote control by withdrawing the bracket while lifting the cover.
• Insert the batteries (type AAA) (not included in the scope of delivery). Ensure correct polarity.
• Insert the battery compartment cover again.

Electrical connection

The electrical motor installed is connected and ready for operation. The connection complies with the applicable VDE and DIN provisions.
The customer‘s mains connection as well as the extension cable used must also comply with these regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is often damaged.
This may have the following causes:

• Pressure points, where connection cables are passed through windows or doors.
• Kinks where the connection cable has been improperly fastened or routed.
• Places where the connection cables have been cut due to being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not be used and are life- threatening due to the insulation damage.
Check the electrical connection cables for damage regularly. Ensure that the connection cables are disconnected from electrical power when checking for damage.
Electrical connection cables must comply with the applicable VDE and DIN provisions. Only use connection cables of the same designation.
The printing of the type designation on the connection cable is mandatory.
For single-phase AC motors, we recommend a fuse rating of C 16A or K 16A for machines with a high starting current (from 3000 watts)!

Cleaning

Danger!
Disconnect the mains plug before carrying out any cleaning work.

• Keep protective devices, air vents and the motor housing as free of dust and dirt as possible. Rub the device clean with a clean cloth or blow it off with compressed air at low pressure.
• We recommend that you clean the device directly after every use.
• Clean the device at regular intervals using a damp cloth and a little soft soap. Do not use any cleaning products or solvents; they could attack the plastic parts of the device. Make sure that no water can penetrate the device interior.  Water entering a power tool will increase the risk of electric shock.

Storage

Store the device and its accessories in a dark, dry and frost-free place that is inaccessible to children. The optimum storage temperature lies between 5 and 30 ˚C. Store the power tool in its original packaging. Cover the power tool to protect it from dust or moisture. Store the operating manual with the power tool.

Maintenance

Filter change (Fig. 6 – 7)
**** Attention! The filter may only be changed after unplugging the mains plug.

• Remove the rear cover (2) by pulling it.
• Now the external filter (6) and the inner filter (7) can be removed.
• The external filter (6) can be blown out.
• The inner filter (7) can be blown out (only to be carried out outdoors!) or rinsed. The filter must be completely dry before putting it back in.
• An arrow is imprinted on the external filter (6) which shows the air flow direction. Ensure that the filter is inserted in the correct direction (Fig. 7).

Service information
With this product, it is necessary to note that the following parts are subject to natural or usage-related wear, or that the following parts are required as consumables.
Wearing parts*: Filter

• may not be included in the scope of supply!
  Connections and repairs
  Connections and repair work on the electrical equipment may only be carried out by electricians.
  Please provide the following information in the event of any queries:

  • Type of current for the motor
  • Data of machine type plate
  • Data of motor type plate

Spare parts and accessories can be obtained from our service centre. To do this, scan the QR code on the cover page.

Disposal and recycling

The device is supplied in packaging to avoid transport damages. This packaging is raw material and can thus be used again or can be reintegrated into the raw material cycle. The device and its accessories are made of different materials, such as metals and plastics. Take defective components to special waste disposal sites. Check with your specialist dealer or municipal administration!
Old devices must not be disposed of with household waste!
This symbol indicates that this product must not be disposed of together with domestic waste in compliance with the Directive (2012/19/EU) pertaining to waste electrical and electronic equipment (WEEE). This product must be handed over at the intended collection point. This can be done, for example, by returning it when purchasing a similar product or delivering it to an authorised collection point for the recycling of old electrical and electronic devices.
Improper handling of waste equipment may have negative consequences for the environment and human health due to potentially hazardous substances that are often contained in electrical and electronic equipment. By properly disposing of this product, you are also contributing to the effective use of natural resources. You can obtain information on collection points for waste equipment from your municipal administration, public waste disposal authority, an authorised body for the disposal of waste electrical and electronic equipment or your waste disposal company.
Batteries and rechargeable batteries do not belong in the household waste!
As the consumer you are required by law to bring all batteries and rechargeable batteries, regardless whether they contain harmful substances or not, to a collection point run by the local authority or to a retailer, so that they can be  disposed of in an environmentally friendly manner.
labelled with: Cd = cadmium, Hg = mercury, Pb = lead Remove the batteries from the laser before disposing of the machine and the batteries.

Troubleshooting

The following table shows fault symptoms and describes remedial measures in the event of your machine failing to work properly. If you cannot localize and rectify the problem with this, please contact your service workshop.

Check mains cable and fuse.
Motor or switch faulty.| Contact an electrician.
Air flow too weak.| External filter blocked.| Blow out or replace filter.
Inner filter blocked.| Blow out or replace filter.

CE Declaration of Conformity

hereby declares the following conformity under the EU Directive and standards for the following article

 Brand :
Art.-Bezeichnung:
Article name:
Nom article:
Art.-Nr. / Art. no.: / N° didn’t.:| SCHEPPACH
HEAVY-DUTY AIR FILTER – HDA-14
5903001901
---|---

Standard references:
EN 60335-1; EN 60335-2-65; EN 55014-1:2017+A11:2020; EN 55014-2:2015; EN IEC 61000-3-2:2019;
EN 61000-3-3:2013+A1:2019
This declaration of conformity is issued under the sole responsibility of the manufacturer.
The object of the declaration described above fulfils the regulations of the directive 2011/65/EU of the European Parliament and Council from 8th June 2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Ichenhausen, den 30.06.2021
Warranty
Apparent defects must be notified within 8 days from the receipt of the goods. Otherwise, the buyers rights of claim due to such defects are invalidated. We guarantee for our machines in case of proper treatment for the time of the statutory warranty period from delivery in such a way that we replace any machine part free of charge which provably becomes unusable due to faulty material or defects of fabrication within such period of time. With respect to parts not manufactured by us we only warrant insofar as we are entitled to warranty claims against the upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer. The cancellation of sale or the reduction of  purchase price as well as any other claims for damages shall be excluded.

www.scheppach.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>