AUDIBAX Detroit 200 Go BT Bluetooth Car Stereo Receiver User Manual
- June 3, 2024
- AUDIBAX
Table of Contents
Detroit 200 Go BT Bluetooth Car Stereo Receiver
User Manual
Detroit 200 Go
BTUSER´S MANUAL
Detroit 200 Go BT
Please read the manual before using the product
Safety Precautions
Do not clean the plastic enclosure with solvents or other chemical based
cleaning products. Do not place heat such as lighting equipment and smoke
machines on the speaker cabinet. Keep the device away from rain and moisture!
Always place the device in a secure manner to prevent the device from causing
injury. Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or
problems.
Additional precautions for amplified devices
The device is designed use in dry conditions only.
Handle the power cord and all connections to the main power with particular
caution! The device should only be connected to 230V AC,50 Hz.
Never handle the power cord or the device when wet, as this could lead to
electronic shock.
Make sure the power-cord is in perfect condition before connecting.
Only handle the power-cord by the plug.
Always insert the power plug last. The power plug must always be interested
without force.
Make sure that the power plug is tightly connected with the outlet.
Never let the power cord come into contact with other cables.
Only replace the fuse when the device is disconnected from the main power.
Only use fuses of the same rating and power. The correct fuse value is
specified on the rear panel.
Bluetooth connection
The first time you connect at device to the PA system, press the [MODE] button
on the MP3-player to enter Bluetooth mode, then find the PA system on the
device you are connecting. When using the connected device with Bluetooth, now
you only need to switch to Bluetooth mode on the PA system’s MP3-player–you
don’t need to connect the device again. If you need use the TWS, just push the
Pair button after change to Bluetooth mode of the two speakers. Then connect
the Bluetooth with one of them, they will play the music together.
How to connect two Detroit 200 Go BT speakers
It is possible to connect two Detroit 200 Go BT speakers with a simple
XLR(male)-to-XLR(female)-cable using one speaker as a master’ and another speaker as aslave’. Connect the female end of the XLR cable to the male mix out’ on themaster’ speaker–then connect the 3-pin male end to the female
line input on the `slave’ speaker.
BATTERY RECHARGE
The speaker has an internal, rechargeable battery capable of up to 6 hours of
continuous audio on a full charge. Even though the speaker may have some
charge when first taken out of the box, we recommend full charging your
speaker before using the system.
To charge the battery:
- Connect the speaker to a power outlet using the included power adapter.
- Keep it plugged in until the indicator changes to 100%, that’s well charged. The speaker utilizes a sealed lithium battery. When not in use, the battery will slowly self-discharge. If you not use the speaker for long time, it should in full charge before storing. Better to charge the unit every six months if no use. It will be good and longer to use. If the battery is in low charge, impossible to recharge the battery, but the charge time is 6 hours more.
OPERATION
Functions
-
SD card slot
-
[TWS Stereo Link] Bluetooth® connection button
-
Display of the built-in media player
-
USB port
-
MP3 Player
MODE| Exchange between: USB/ SD/ BLUETOOTH REMOTE CONTROL
---|---
| Play/Pause
| Repeat
| Last
****| Next -
[MASTER] Rotary control to adjust the overall volume
-
[MUSIC] / [SPEECH] — [BASS BOOST] Rotary control to adjust the bass. Turn the control to the left to reduce the bass. Turn the control to the right to increase the bass.
-
[LEVEL] Rotary control for adjusting the volume of the input signal at the line input
-
[POWER] / [LIMIT] Indicator LEDs for power supply and limiter
[POWER]: The LED lights up green once the unit is powered.
[LIMIT]: The LED lights up green when the signal is clipping. Turn down the control for the master volume ([MASTER]) until the LED is no longer lit. -
[LINE | MP3] Input signal switch. Use this button to toggle between external ([LINE] input) and internal signal source (built-in media player). When pressed, [MP3] the signal of the internal media player is played. When not pressed, [LINE] the audio signal of an external audio player is played.
-
[LINE] 3.5 mm mini jack socket to connect an external audio device (CD or MP3 player)
-
[LINE OUT] Line output, designed as XLR output socket, 3-pin
-
[MIC/LINE 1] and [MIC/LINE 2] Mic / line inputs, designed as XLR input socket, 3-pin 14. Mic / line inputs, designed as 1/4″ jack socket
-
[MIC] / [LINE] for channel 1 and 2 Toggle switch for the input signal of the respective channel. Use these buttons to switch between mic and line input. When pressed, [MIC] the microphone signal is played. When not pressed, [LINE] the line signal is played.
-
[LEVEL 1] and [LEVEL 2] Rotary control for adjusting the volume of the input signal at the line input of channel 1 or 2
-
[EFFECT 1] and [EFFECT 2] Rotary control for adjusting the echo effect of the input signal at the line input of channel 1 or 2
-
IEC chassis plug with fuse holder for the power supply
-
[POWER] On / off switch
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>