Beca BHT-2002GBLW Floor Heating Control User Manual

Beca BHT-2002GBLW Floor Heating Control

Instruction

For Water Heating/Boiler/Electric Heating
Thank you for purchasing our products, please read the following terms before installation and use:
Please confirm that this product is suitable for your heating equipment before installation;

• Before installation or maintenance, please make sure to keep the power off;
• Please strictly follow the wiring diagram for wiring installation;
• Installation to the wall, please confirm that the fasteners are suitable for this product;
• Do not pull the cable too hard, otherwise the product will be * If a hard plastic wire is used in the installation process, it must be bent to an appropriate angle in advance;
• Please arrange for professionals to install;
• Please contact the after-sales service for equipment failure, please do not try to repair it yourself;
• After installation, please refer to this manual to check again to  ensure normal and safe use, and keep this manual properly.

ABOUT YOUR THERMOSTATS
The BHT-2002 range has been developed to control electric underfloor ,water heating or water/gas boiler system. These units are designed for use in commercial, industrial, civil and domestic properties. In the box you will find

TECHNICAL DATA

• Power Supply:95 ~240 VAC, 50~60Hz
• Current Load: 5A (Water heating, water/Gas boiler), 16A (Electric heating)
• Sensor: NTC3950, 10K
• Accuracy: ±0.5°C
• Set Temp. Range: 5-35°C
• Room Temp. Range: 5-99°C
• Display Temp. Range: 5 ~ 99°C
• Ambient Temp.: 0~ 45°C
• Ambient Humidity: 5 ~ 95 % RH (Non Condensing)
• Storage Temp.:-5~ 45°C
• Power Consumption: <1. 5W
• Timing Error: < 1%
• Shell Material: PC +ABS ( Fireproof)
• Installation Box: 86 * 86mm Square or European 60mm Round Box Wire Terminals: Wire 2 x 1.5 mm2 or 1 x 2.5 mm2
• Protection Class: IP20
• Buttons: Capacitive Touch Buttons

MODEL DEFINITION

• GA: Water heating, 5A
• GB: Electric floor Heating,16A GC: Water/Gas Boiler, 3A
• L: Backlight
• W: Wifi
• For example: BHT-2002 GCLW

FEATURES

On Appearance

• Excellent UI design, both beautiful and practical.
• H9 tempered glass screen, scratch-resistant and easy to clean;
• Compatible with standard 86mm square cassettes and 60mm European cassettes to meet all installation environments;

On Functionality

• Strict temperature control accuracy (± 0.5°C) to provide the warmth you want;
• Power off protection, save all your settings safely;
•  Provide weather information and humidity display
• Preset adjustment of 5+1+1 mode in a week, programmable setting of 6 time periods a day, green energy saving, Less cost, more intelligent and environmental protection;
• Support the creation of product local groups/shares to achieve unlimited centralized control of the number of products/ multi-terminal control;
• Perfect access: Tmall Genie, Amazon echo, Google Home, full experience new voice control method;

DIMENSION:(mm)

BEFORE WIRING AND INSTALLING

1. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition.
2. Check the rathings given in the instructions and on the product to make  sure the product is suitable for your application.
3. Installer must be a trained, experienced service technician.
4. After installation is complete, check out product operation as provided in these instructions.

Note:
GA is for water heating; GB is for electric heating; GC is for water/gas boiler; NTC and Modbus is optional.

Wiring

Note:

• GA is for water heating;
• GB is for electric heating;
• GC is for water/gas boiler;
• NTC and Modbus is optional.

Electrical Shock or Equipment Damage Hazard. Can shock individuals orshort equipment circuitry. Disconnect power supply before installation.

INSTALLATION

Your thermostat is suitable for installation within a standard 86mm
press box or European 60mm press box.

• Step 1. Keep power off. See Fig 1.

• Step 2. Remove the mounting plate by pushing the panel assembly. See Fig 2.

• Step 3. Connect power supply, load into the appropriate terminals.(see “Wiring your thermostat” for details and Fig 3).

• Step 4. Fix the mounting plate into the wall with screws in the box. See Fig 4.

• Step 5. Fix the thermostat body and the mounting plate by the lower button. See Fig 5.

• Step 6. Installation complete. See Fig 6.

HOME SCREEN QUICK REFERENCE

Note: The weather and humidity will be synchronized within 1 hour after the device is connected to the Internet for the first time, and the weather will be synchronized every hour thereafter. Press the / in the power-on state to display the humidity and set temperature

OPERATION

During Power On

1. Power On/off: Press

2. . Function & Programmable
   Touch to change between manual mode and programmemode.
   In manual mode, will show on the display,
   In programmable mode, and will show on the display.

3. Setting Temperature
   In the programming mode, the temperature setting and time setting will be locked. If the user wants to adjust, he must first adjust the thermostat to manual mode by pressing the key.
   In the mode of manual, press to set the desired temperature.

4. Adjusting/Setting the Clock

5. Locking your Thermostat
   Press and hold the for 8 seconds to lock In item 3 of high senior options, you can select full lock or half lock.

6. Adjusting/Setting the Programmable Schedules

Press the icon again, the temperature setting will flash, set the temperature by ;
This completes the setting of periods1 .”

Time display

| MON.-FRI.

(①②③④⑤ shows on scteen)

| SAT.

(⑥shows on scteen)

| SUN.

(⑦shows on scteen)

---|---|---|---
TIME| TEMP.| ON TIME| TEMP.| ON TIME| TEMP.
Period 1| 6:00~8:00| 20| 6:00~8:00| 20| 6:00~8:00| 20
Period 2| 8:00~11:30| 15| 8:00~11:30| 20| 8:00~11:30| 20
Period 3| 11:30~13:00| 15| 11:30~13:00| 20| 11:30~13:00| 20
Period 4| 13:30~17:00| 15| 13:30~17:00| 20| 13:30~17:00| 20
Period 5| 17:00~22:00| 22| 17:00~22:00| 20| 17:00~22:00| 20
Period 6| 22:00~6:00| 15| 22:00~6:00| 15| 22:00~6:00| 15

In the same way, complete the settings of periods2, 3, 4,5and 6.
Press the icon once more to enter the Saturday schedule settings (you will see the SAT of the screen).Repeat the above process to set the period and temp. and Sunday schedule.
Press the icon once more to confirm and exit.
Default settings for program schedule
A separate schedule may be set for weekdays (Mon – Fri) and for weekends (Sat or Sun).
Checking the Temperature of Floor Sensor
Press and hold the arrow f or 8 seconds to display the temp. of floor sensor. If there is no external external sensor, “err” will be displayed.
Setting the Functions and Options
During Power Off, press and hold and order to reach system function. Then press the available functions.

3

|

Button Locking

| 01:All buttons are locked except power button. 01:All buttons are locked.|

01

4

|

Sensor typer

| In:Internal Sensor(to control the temp.) Ex:External Sensor(to control the temp.) Ou:Only external sensor

AL:Internal/External Sensor (Internal sensor to control the temp., external sensor to limit the

temp.)

|

AL

5| Min.Set Temp.| 5-15℃| 5
6| Max.Set Temp.| 15-45℃| 35
7| High temperature

protection setting.

| 25-70℃| 45
8| Low temperature protection setting.| 0-10℃| 0
9| Energy saving Mode| 00:Non-energy saving Mode 01:Energy saving Mode| 00
10| Energy saving

Temp.

| 0-30℃| 20
11| Standby Brightness| 3-99| 5
12| Version number| | U1

ABOUT WIFI

WI-FI CONNECTION
Before using your Wi-Fi thermostat for the first time, you must configure the Wi-Fi signal and settings through your smartphone or tablet ,This will all ow communication between your connected devices

• Step 1 Downlosd your APP
  Search for “Smartlife” in Apple Store or Google Play or use a browser to scan the QR code above (Figure 1-2), and complete account registration and installation according to the guidance of the APP.

• Step 2. Connect the thermostat
  Check the tutorial below to complete the connection and setup
  Method 1: Scan the QR code to configure the network guide (Fig 2.1-Fig 2.3) Method 2: Ordinary distribution network guidance (Fig. 2. 1&Fig. 2.3.1)

Network distribution mode:

1. EZ Mode
   When the thermostat is off, press and then operate according to the following figure (Fig 2.4-Fig 2.7).

2. AP Mode
   When the thermostat is off, press and hold the ” ” until the thermostat screen flashes slowly and the ” ” icon is displayed (if the ” ” icon appears, continue to press the ” ” until the thermostat screen Flashes slowly and displays the “ ” icon), and then operate according to the following figure (Fig 2.8-Fig 2.14).

APP operation interface description (heating thermostat)）

More settings

SIMPLE EXCEPTION HANDLING

and Power Unit Box is loosen.
2| Without output but display works.| Usea new LC panel or new Power Unit Box to replace the old one.
3| Room Temp. Is a titlle different from the actual.| Do temperature calibration in item 1 of high senior options

SERVICE

Your thermostat carries an 24 months warranty
from date of purchase. Service outwith the warranty period mayincur a charge. More detail please contact with us directly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>