udiRC U46S Induction Drone Only Indoor Flight User Guide
- June 3, 2024
- Udirc
Table of Contents
udiRC U46S Induction Drone Only Indoor Flight
Note
- This product is suitable for users over 14 years old.
- Stay away from the rotating propeller
- Read the “important statement and safety guidelines” carefully.
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household trash. Please contact local environmental waste agency or the supplier of your model or your nearest Li-Po battery recycling center.
Important Notice
Our company’s products are improving all the time, design and specifications are subject to change without notice. All the information in this manual has been carefully checked to ensure accuracy, if any printing errors, our company reserve the final interpretation right.
Ready before flight
Drone Overview
TOP
Drone Battery Charger
Connect drone battery with included USB charger cable, and then connect to other USB output port (Output: 5V 2A). The USB charger indicator light will red when charging and the light turns green when fully charged.
Warning: Must be supervised while charging Please use the included USB charging cable and make sure it is properly connected.
Drone Battery Installation
Install the batteries in order, and remove them in reverse.
- Open the battery cover.
- Put the battery in it.
- Plug the battery plug into the body socket and close the battery cover.
Transmitter preparation
Control stick operation
Left stick
- Go up
- Go down
- Counterclockwise turn
- Clockwise turn
Right stick
- Forward
- Backward
- Fly to the left
- Fly to the right
Battery Installation
Open the transmitter battery cover. Install batteries. Follow the direction of batteries designated in the inside of the battery box.
Flight Operations
Drone preparation
- Turn me on in a room with lots of space(Suggest ≥16m²) Turn on the power of the drone, the navigation lights changes from flash quickly to flash slowly. It indicates to enter frequency state.
- Turn on the power on the transmitter, the Power-LED will flash quickly. Pull the left stick to the lowest position and let go, the Power-LED changes from flash to keep long bright. The navigations will keep long bright. It indicates frequency pairing is successful.
Emergency Stop: During the flight, press the” ” button for about 2 seconds, the transmitter will sound “di. di…” and the drone crashes directly.
Tip: Do not use the emergency stop function unless in emergency situation.
Heading Hold Mode
Flying Trimmer
Forward / Backward Trimmer
- During the flight, if the drone tilts forward, press down the left stick in the center button, and push the right stick backward. Otherwise push forwards.
Left / right side flying trimmer
- During the flight, if the drone tilts to left, then press down the left stick in the center button and push the right stick to right to adjust. Otherwise push to left.
Left / right turning trimmer
- During the flight, if the drone head rotates to left, then press down the left stick in the center button and push the left stick to right. Otherwise push to left.
Calibration
(Use when the flight is abnormal)
After successful frequency alignment, the right stick is pushed to the lower right corner by 45°, and the drone navigation lights turns to keep bright after quick flashing, indicating that the gyroscope has been calibrated. Release the right stick.
Tips: Restart the power of the transmitter and the drone to enter the calibration after the frequency paring is successful.
Low Battery Alarm
- Transmitter: When the power of the transmitter is nearly exhausted, the Power-LED will continue flash. At this time, you must return back to replace the battery soon.
- Drone: When the drone in low battery, the navigation lights will continue to “flash and stop”, the drone must return home at this time.
Stuck Protection
- When the propellers get stuck, then activate stuck protection function and the motors stop running.
- Pull down the left stick to the lowest position and then go back to the center, stuck protection will be released and the drone can fly again.
ATTENTION
- Switching sequence. At first, turn on the power of the drone, then turn on the power of the transmitter. After the end, turn off the power of the drone first, and then turn off the power of the transmitter.
- Improper operation caused the crash. It is necessary to check and confirm the connection of the motor, propeller or battery of the drone and the damage degree, so that the drone can fly again. If there is damaged, please replace the new accessories or prone to accident.
Propeller Replacement
Disassembly
- Hold the propeller vertically and then pull the propeller out.
Installation
- Mount propeller aim the central shaft of the motor and press down.
ATTENTION: The letter on the propeller corresponds to the letter mark on the motor base. The propeller must be installed correctly, otherwise cannot fly.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. Modifications not authorized by the manufacturer may void user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
DANGER: Only suitable for ages 14+
Warning
- The product should only be used by adults and children over 14 years.
- Adult supervision is required for children under 14 years.
Manufacturer
SHANTOU CITY CHENGHAI UDIRC TOYS CO., LTD
Address: Guangfeng Industrial Zone, Guangyi Street, Chenghai District, Shantou City, Guangdong Province, CN
Model: U46S
MADE IN CHINA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>