udiRC U59 RC Quadcopter Drone User Manual
- June 4, 2024
- Udirc
Table of Contents
- Ready before take-off
- Drone battery installation
- Transmitter preparation
- Mobile Phone Installation
- Flight Operations
- Transmitter connects with drone
- Control stick operation
- Speed mode switch
- Gimbal adjustment
- Intelligent Hover
- Parts replacement
- Troubleshooting
- FCC Note
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
USER
This product supports GPS positioning and is recommended for outdoor
flights!
This wifi camera pinpoint is 5G, please confirm whether the phone is
supported.
MANUAL
U59
- This product is suitable for users over 14 years old.
- Stay away from the rotating propeller
- Read the “important statement and safety guidelines” carefully.
Ready before take-off
Drone preparation
Battery Charger
Battery power is insufficient in the original plant. It must be charged
saturated before it can be used.
Connect the original charging cable with the drone battery, and then connect
another USB charging port. The charger line indicator is red when charging and
the light turns green when fully charged.
- Only use the original charging line; suggest select adapters with an output current of 5V 2A.
Drone battery installation
Installation: Push the battery to the bottom of the body battery slot.
Disassembly: Press the battery lock and pull the battery out backward.
Landing gear installation
Installation: Aim the landing gear frame to the body and place it in the right
place.
Disassembly: Pull out the landing gear.
Note: Make the landing gear close to the fuselage the surface of the
drone, otherwise it will be unstable and affect the stability of the drone
Installation of TF Card
Insert the TF card into the slot of the camera, and pay attention to the metal contact surface orientation of the TF card.
Transmitter preparation
Transmitter battery installation
Open the battery cover on the back side of the transmitter: according to the
“+-” electrode instruction in the battery groove, and place the battery with
the
the same type of saturated power (battery not included).
Mobile Phone Installation
* Pay attention to don’t clip the buttons on the side of the phone.
Flight Operations
Mobile phone connect with Drone
Download and install APP: UDIGPS
This software is suitable for mobile phones in the IOS and Android system.
For detailed operation, please check the system “HELP” of the APP.
http://www.udirc.com/udigps-download
Transmitter connects with drone
Frequency Pairing
-
Turn on the power of the transmitter.
-
Pull the left stick to the lowest position and let go, the indicator light changed to slow flash. It indicates the transmitter enters the frequency state.
-
Long press the power of the drone for 2 seconds and placed it on the horizontal ground. After the navigation light is on for 2 seconds, the fuselage lights become flash, and the drone and the transmitter are connected to each other successfully. When the left light of the drone flashes and the right light does not turn on, it is suggested that the horizontal correction of the compass is needed at this time.
Compass calibration
Rotate the drone horizontally until the transmitter sounds “di… “Level
correction to complete. When the left light turns to long light and the right
light flashes, enter a vertical correction.
Rotate the drone vertically until the transmitter sounds “di… “A sound,
vertical correction over. The four navigation lights are spinning and
flashing.
Tips: It’s a must to have the right compass adjustment first each time
you start the drone or it can’t work normally
GPS signal search
After the frequency matching is successful, the drone automatically searches
for GPS signals. When the left blue indicator light of the transmitter changes
from flashing to long bright, indicating that the GPS connection is
successful. But if you don’t connect the GPS, the flight height defaults to
about 4 meters.
Unlocking the drone
Push the left and right stick inward to the 45-degree angle simultaneously.
- On standby drone, motor rotation, drone Unlocked.
- When the drone is not taken off, the motor stops rotating and the drone is locked.
The drone can only take off when the motor is unlocked.
Control stick operation
Left stick
Take off
After unlocking the motor:push up the left stick slowly and the drone rises
slowly.
Landing
During the flight: push down the left stick slowly and the drone land slowly
until landing.
Return
During the flight, press the “return ” button, and the transmitter will sound
“di”, and the drone will automatically return to the take-off point. (during
returning, the transmitter will continuously sound “di”. To stop homing, just
press this button again.)
GPS ON / OFF
GPS is turned on by default.
GPS OFF: Press the GPS switch button, and the transmitter will sound “di” ,
and the blue indicator of the transmitter will go off, it means GPS will be
off.
GPS ON;Press the GPS switch button to restart GPS.
Note: this function is only used when the motor is locked.
Following mode
While flying, press the“following” button, and the transmitter will sounds
“di”, the drone enters the function of following. Now it can be controlled by
the user. The function is standard by the mobile phone APP signal, so it’s a
must to make the drone and APP connected normally, and turn on the mobile
location service at the same time, otherwise, this function is invalid.
Note: The following maximum range is within 300m of the take-
off point.
Encircling mode
In light. press he -Encircling ‘button. and Ito transmitter sound of %Y. Then
it goes to the fun akin el enticing flint!. The thane male flies to a debut
radius then it waits for the direction corcrolle0 hype user. Adjust the speed
and direction 04 the drone by Manpulatilg 11)3 rigid stick. It Is the minimum
radius of 11,3 Colaull [WAS aCeuieSeefitly so &One flies Only in the Sub
large.
In the state of encircling flying, the left stick could only control the height of the drone.
Speed mode switch
Press “H/L” it will make the sound”di” di. di” three times to enter high-speed mode “H”; Press down it again, it will make the sound”di” , this indicates to the low-speed mode” L; Press down again, it makes the sound of ‘di’ for twice, it comes to the middle-speed mode “M”.
Medium speed default
Low speed: suitable for beginners to practice without wind.
Medium speed: suitable for skilled operators operating in the light breeze.
High speed: suitable for professional operation in outdoor wind resistance.
Gimbal adjustment
Scroll Gimbal button to adjust the camera angle.
Photo
Press “photo ”button once to take a picture.
When taking photos, the transmitter will sound “di” .
Video
Press the “video” button the transmitter will sound “didi” to remind the
user to enter the recording state and repeat this action to stop recording and
save the video.
Notes for Filming
- Photos taken will be saved to the mobile picture library and drone TF card; Video can be saved in the TF card first, which can be downloaded to the mobile picture library for viewing. Please download the video according to APP prompt. When downloading, maintain the normal connection between the mobile phone and the flyer, and the TF card is in the card slot.
- The APP must be authorized to read the phone gallery to view the aerial photos.
- Turn off the power supply of the drone before taking out the TF card.
- When the aerial video is read by the computer, it must have corresponding playback software.
Intelligent Hover
Intelligent flight control can calculate the suspended height, the visual
system points to the ground position, and GPS coordinates allow the vehicle to
stay in your desired position Buy. The drone is like a camera fixed in the
air. Aerial photography and control are very convenient.
Notice: Drone must be connected to GPS properly in order to give full
play to fixed- point hovering function. Atmospheric pressure or wind force
affects hovering stability.
Low Battery Alarm
When the battery power of the point remote is quickly exhausted, it will make
the sound of “di” constantly alarms you, now you should land the
drone as soon as possible to replace the battery of the transmitter.
Automatic Return
While flying, in case the battery of the drone is quickly exhausted, it will
make the sound of “di”.“di” to alarm you, and the drone’s indicator lights
turn from long to bright. After alarming you, the drone automatically returned
to the take-off point.
Notice: After the low-battery alarm, the drone will return home. Meanwhile,
its controllable range will be reached 20 meters.
Out of Range Alarm
When the drone flies out of the max remote control distance, the transmitter
will beep “di” to alarm the user to fly back the drone within range
immediately.
Stuck Protection
- When the propeller is stuck and doesn’t turn around, the LED light will make a fast flicker to star protection automatically. Meanwhile, the motor stops turning.
- Reset the left stick to the lowest position and return to the middle position, at this time the LED light keeps bright to unlock the protection function automatically, then the drone can take off normally
Out of Control Protection
Out-of-control protection refers to the flight control system automatically
controlling the drone to fly back to the return point after receiving the
remote
control signal (ie, out of control). The drone does not have the function of
avoiding obstacles during the uncontrolled return flight. The user can set the
return altitude value to avoid obstacles on the way back.
Possibility of entry into runaway protection mode
- The transmitter is off.
- Flight distance exceeds the effective distance of remote control signal transmission.
- There is an obstacle between the transmitter and the drone.
- The transmitter signal is disturbed.
Flying Trimmer
Forward / Backward Trimmer
When flying, if the drone tilts forward, push the left stick down and push the
right stick down. Otherwise push it up.
Left / Right Tilts Trimmer
When flying, if the drone tilts to the left, push the right stick down,
meantime push the right stick to the right. Otherwise push it to the left.
Left / Right Rotates Trimmer
When flying, if the drone head rotates to the left, push the right stick down,
meantime push the left stick to the right. Otherwise push it to the left.
Calibration (This action is used when flying abnormally)
After the calibration of the compass, the right control lever of the remote
control is pushed to the lower right corner by 45°, and the remote control
emits a sound of “di”, and the aircraft light flashes and releases,indicating
that the gyroscope has been calibrated.
Tips: When the drone doesn’t appear to use the trim correction flight
status or is being hit hard (or falling abnormally). thus causing difficulties
in controlling. Now frequency making and adjustment are needed again, the
drone should be placed on horizontal ground.
Attention
-
Switching sequence. First, turn on the power of the transmitter, then turn on the power of the drone. After the end, turn off the power of the drone
first, and then turn off the power of the transmitter. -
The improper operation caused the crash. It is necessary to check and confirm the connection of the motor: propeller or battery of the drone and the
damage degree so that the drone can fly again. If it is damaged, please replace the new accessories, or prone to accident.
Parts replacement
Propeller replacement
Disassembly:First screw out the screw then pull out the propeller.
Installation:Make sure that the propeller aims at the hole direction of the
drone hole then press it down to the bottom, and screw the screw.
The propeller hole on the propeller fits the motor hole.
There is different A and B remarks on the propeller. Be sure that the
propellers are installed to the correct motors, which remarked the Letters to
identify on the motor holder, if not, then the drone can not work
normally.
Please make sure that the propellers are installed correctly, otherwise,
the drone cannot fly.
Drone Battery Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household trash.
Please contact the local environmental or waste agency or the supplier of your
model or your nearest Li-Po battery recycling center.
Our company’s products are improving all the time, design and specifications
are subject to change without notice.
Important Notice
All the information in this manual has been carefully checked to ensure
accuracy, if any printing errors, our company reserve the final interpretation
right.
Troubleshooting
Problem| Problem cause|
Solution
---|---|---
The controller Indicator light is off.| Low battery.| Replace the controller
battery.
The batteries are incorrect.| Install the batteries following the polarity
indicators.
The batteries are incorrectly positioned.| Clean the dirt between the battery
and the battery contacts.
Failed to pair the drone with the controller.| The indicator light is off.|
The same as above.
There is an interfering signal nearby.| Restart the drone and power on the
controller.
Mis-operation.| Operate the drone step by step in accordance with the user
manual.
The electronic component is damaged by the fierce crashes.| To buy spare parts
from local sellers and replace damaged parts.
The drone is under-powered or can not fly.| The propeller is seriously
deformed.| Replace the propeller.
Low battery.| Charge the drone battery.
Incorrect installation of the propeller.| Install the propeller in accordance
with the user manual.
The drone could not hover and tilted to one side.| Improper Calibration.|
Please refer to the Calibration.
The propeller is serious.| Replace the propeller.
The motor holder is deformed after a violent crash.| Replace the motor holder
parts.
The gyroscope did not reset after a serious crash.| Put the drone on flat
ground for about 10 minutes or restart the drone to calibrate again.
The motor is damaged.| Replace the motor.
The drone indicator light is off.| Low battery.| Recharge the drone battery.
The battery is expired or over-discharge protection.| Buy a new battery from
the local seller to replace the battery or charge the battery.
Poor contact| Connect and disconnect the battery.
Could not see the picture.| There is an interfering signal nearby.| Practice
and read the cellphone controlling instructions carefully.
Camera is damaged.| Replace Camera.
Hard to control by cell phone.| Not experienced enough.| Practice and read the
cellphone controlling instructions carefully.
Can’t altitude hold?| The propeller is serious.| Replace propeller.
Motor is damaged| Replace the motor.
Atmospheric pressure is not stable.| Refer to the “Altitude Hold Mode”
instruction.
Can’t position hold.| Whether the GPS has connected or not.| Search again to
connect the GPS signal.
Searched but could not find the GPS signal.| GPS module is damaged.| Please
replace a new one.
GPS module plug is loose.| Please check to see if it’s connected normally.
FCC Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Notice:
The equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. Modifications
not authorized by the manufacturer may void the user’s authority to operate
this device. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
Manufacturer
Company: SHANTOU CITY CHENGHAI UDIRC TOYS CO., LTD
Manufacture address: Guangfeng Industrial Zone, Guangyi Street, Chenghai
District, Shantou City, Guangdong Province, China Model: U59
Manufacture time:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>