Chenghai Udirc Toys ZKWCY581707001 5.8G WIFI FPV DRONE User Manual
- June 5, 2024
- Chenghai Udirc Toys
Table of Contents
WIFI FPV DRONE
User Manual
This product supports GPS positioning and is recommended for outdoor flights!
This wifi camera pinpoint is 5G, please confirm whether the phone is
supported.
This product is suitable for users over 14 years old.
Stay away from the rotating propeller A
**** Read the Important statement and safety guidelines carefully.
Ready before take-off
Drone preparation
Unfolding Instruction
Battery Charger
Battery power is insufficient in the original plant. It must be charged
saturated before it can be used.
Connect the batteries of the drone to the charging line of the original plant,
and then connect to other USB charging sockets. Battery indicator flashes when
charged. When the charging is completed, the battery indicator light is always
on.
Battery Installation
Insert the TF card
insert the slot on the belly of the fuselage, and pay attention to the metal contact surface orientation of the TF card.
Transmitter
The original transmitter is low in power, so it should be used after saturation.
Transmitter charging
**** Only use the original charging line; Adapters with output current of
5Va.2A must be selected.
Connect the transmitter with the charging line of the original plant, and then
connect other USB charging outlets. When charging, the transmitter indicator
flashes circularly, and when charging is completed, the indicator will be on
for a long time.
The installation methods of mobile phone holder
The installation methods of
mobile phone
Flight Operations
Mobile phone connect with Drone
Download and install APP: UDIGPS
http://www.udirc.com/udigps-download
This software is suitable for mobile phones i the 108 and Android systems. For detailed operation, please check the system “HELP” of the APP.
Transmitter connects with Drone
Frequency Pairing
- Turn on the power.
- Pull the left stick to the lowest position and let go, the light goes off slowly. it indicates the transmitter enters the frequency state.
- The drone is placed on the horizontal ground, and long-press the power button for 2 seconds to start the machine. After the navigation light is on for 2 seconds,the front navigation light flashes, and the rear navigation light goes out. At the same time, the remote control emits a prompt sound of “di”, indicating successful frequency alignment and entering the horizontal calibration of compass.
Compass calibration
Rotate the drone horizontally until the transmitter sounds “di… ‘Level
correction to complete. When the front navigation light turns to long light
and the rear navigation light flashes, enter a vertical correction.
Rotate the drone vertically until the transmitter sounds “di… ” A sound,
vertical correction over. The lights are spinning and flashing.
Tips: It’s a must to have the right compass adjustment first each time you start the drone, or it can’t work normally
GPS signal search
After the frequency matching is successful, the drone automatically searches
for GPS signals. When the blue indicator light of the remote control changes
from flashing to long bright, it makes a sound of “di” at the same time,
indicating that the GPS connection is successful. (when the GPS signal is weak
or flying indoors, the flight height defaults to about 4 meters).
Unlocking / Lockin I the motor
Push the left and right stick inward to the 45-degree angle simultaneously.
- On-standby drone, motor rotation, drone Unlocked.
- When the drone is not taken off, the motor stops rotating and the drone is locked.
The drone can only take ott when the motor is unlocked.
Control stick operation
Left stick
Right Stick
Take off
After unlocking the motor, the left control lever slowly pushes up and the
drone slowly rises.
Landing
During the flight, the left control lever slowly pull down, and the drone
slowly lands until landing.
Return
During the flight, press the “return ” button, and the transmitter will sound
“di”, and the drone will automatically return to the take-off point. (During
returning, the transmitter will continuously sound “di”. To stop homing, just
press this button again.)
Notice: While returning, the control lever of the transmitter can not control the drone, it must be waited for the drone to go back to the take-off point. And atter the direction of the drone is directed at the direction of taking off, in this way right stick can control the drone.
GPS ON /OFF
GPS is on by default. GPS OFF: Press the “GPS “button,the transmitter will
sound “di” and the blue indicator of the transmitter will go off, it means GPS
will be off. GPS ON: Press the”GPS•button and the blue indicator of the
transmitter will keep bright. It means GPS restart.
Note: this function Is only used when the motor Is locked.
Following Function
While flying, press down the key, the transmitter sounds “di”, drone enters
the function of following. Now it can be controlled by the user.
The function is standard by the mobile phone APP signal, so it’s a must to
make the drone and App connected normally, turn on the mobile location service
at the same time, otherwise this function is invalid.
Note: follow the maximum range distance, within 300m of the take-off
point.
Encircling flight
In-flight press the “encircle” button, and the transmitter will make the sound
of ‘di”. Then it goes to the function of encircling flight The drone MI fly to
a default radius then it waits for the direction controlled by the user.
Adjust the speed and direction of the drone by manipulating the right stick.
It Is the minimum radius of the default radius acquiescently so the drone
flies only in the sub-range.
Speed mode switch
Press 11C and make. DI. Di” three times to enter high-speed mode II” ; Press
it down again. it will make the sound again,this indicates to the low-speed
mode”L; Press down the key again, it makes the sound of ‘dl’ for twice, it
comes to the middle-speed mode “M”.
Power on at default medium speed.
Low speed: suitable fa beginners to practice without wind.
Medium speed: suitable for skilled operators operating In fight breeze.
Mph speed: suitable for professional operation in outdoor wild resistance.
Gimbal Adjustment
Photo
Press the “photo” button once to take a picture.
When taking photos, the transmitter MI sends out a “di” sound.
Video
Press the ‘video” button to enter the recording state, and the transmitter
will prompt “didi” to repeat this action to stop recording and save the video.
Notes for Filming
- Photos taken will be saved to the mobile picture library and aircraft TF card; Video can be saved In TF card first, which can be downloaded to the mobile picture library for viewing. Please download video according to APP prompt. When downloading, maintain the normal connection between the mobile phone and the flyer, and the TF card is in the card slot.
- The APP must be authorized to read the phone gallery to view the aerial photos.
- Turn off the power supply of the drone before taking out the TF card.
- When the aerial video is read by a computer, it must have corresponding playback software.
Intelligent Hover
Intelligent flight control can calculate the suspended height,the visual
system points the ground position, GPS coordinates allow the vehicle to stay
in your desired position Buy. The drone is like a camera fixed in the air.
Aerial photography and control are very convenient.
Notice: Drone must be connected to GPS properly in order to give full play to
the fixed-point hovering function. Atmospheric pressure or wind force affects
hovering stabibty.
Low Battery Alarm
When the battery power of the point remote is quickly exhausted, it will make
the sound of “dindi””di” constantly to alarm you, now you should land the
drone as soon as possible to charge the battery.
Automatic Return
While flying, in case that the battery of the drone is quickly exhausted, it
will make the sound of “di”.”di” to alarm you, the drone’s indicator lights
turn from long to bright. After alarming you, the drone automatically returned
to the take-off point. Notice: After low-battery alarm, the drone will return
home. Meanwhile, its controllable range wit be reached to the 20 meter
Out of Range Alarm
When the drone flies out of the max remote control distance, the transmitter
will beep “didi…didi…didi…” to alarm the user to fly back the drone within
range immediately.
Stuck Protection
- When the propeller is stuck and does not rotate, the drone will start the automatic protection function to stop the motor working.
- Reset the left stick to the lowest position and return to the middle position, at this time the LED light keeps bright to unlock the protection function automatically, then the drone can take off normally.
Out of Control Protection
Out-of-control protection refers to the flight control system that
automatically controls the drone to fly back to the return point after
receiving the remote control signal (ie, out of control), the drone does not
have the function of avoiding obstacles during the uncontrolled return
flight.? The user can set the return attitude value to avoid obstacles on the
way back.
Possibility of entry into runaway protection mode
- The remote control is off.
- Flight distance exceeds the effective distance of remote control signal transmission.
- There is an obstacle between the transmitter and the drone.
- The transmitter signal is disturbed.
Flying Trimmer
| Forward / Backward Trimmer
When flying, if the drone tilts forward, push the left stick down and push the
right stick down. Otherwise push it up
---|---
| Left / Right Tilts Trimmer
When flying, if the drone tilts to the left, push the left stick down,
meantime push the right stick to the right. Otherwise push it to the left.
| Left / Right Rotates Trimmer
When flying, if the drone head rotates to the left, push the right stick down,
meantime push lethe ft stick to right. Otherwise push it to the left.
After the calibration of the compass, the right control lever of the remote control is pushed to the lower right corner by 45°, and the remote control will sound of “di”, and the aircraft light flashes and releases, indicating that the gyroscope has been calibrated. (drone should be placed on the horizontal ground)
Tips: When the drone doesn’t appear to use the trim correction flight status or is being hit hard (or falling abnormally). thus cause difficulties in controlling. Now frequency making and adjustment are needed again.
Propeller replacement
Disassembly: The first screw out the screw then pull out the propeller.
Installation: Make sure that the propeller aims at the hole direction of
the drone hole then press it down to the bottom and lock the screw.
Note: There are marked ‘A” and “8” on the back of the propeller. Please
carefully check the letters “A” and I” on the folding arm of the drone.The two
letters must correspond to each other during installation.
Attention
- Switching sequence. At first, turn on the power of the transmitter, then turn on the power of the drone. After the end, turn off the power of the drone first, and then turn off the power of the transmitter.
- The improper operation caused the crash. It is necessary to check and confirm the connection of the motor, blade or electric pool of the aircraft and the damage degree so that the aircraft can fly again. If it is damaged, please replace it with new accessories,s, otherwise, it will easily cause flight accidents.
- Battery must be removed when the drone is not in use.
Drone Battery Li-Po Battery Disposal & Recycling
Wasted lithium-Polymer batteries must not be placed with household e_ 111
trash. Please contact the local environmental or waste agency or the supplier
of your model or your nearest Li-Po battery recycling center.
Important Notice
Our company products are improving al the time. design and specifications are
subject to change without notice. All the iMorrnation in this manual has been
carefully checked to ensure accuracy. d any printing errors. our company
reserve the final interpretation right.
Parameter
Drone
Weight: 270g (Including battery)
Size: Folded: 1509660mm Diagonal: 26326360mm
Propeller diameter 155mm
Maximum ascent rate: 1.7m/s
Maximum descent rate: 1.7m/s
Maximum speed: About 201(m/h Flight attitude limit 250m
Maximum flight time: 17 minutes(calm)
Maximum wind speed: level 3
Maximum tilt angle: 35°
Operating Temperature Range: 0°C to 40°C
GNSS: GPS/GLONASS
Operating frequency: 2.4Ghz /5G wifi
Gimbal
Stable: Single-axis (tilt)
Controllable range: Tilting: -90° to 0°
Camera
Image resolution: 2048x1152P
Static Photography Mode: Single shoot
Video Resolution: 2048*1152P
Image mode: RGB Mode
Frame Rate: 25
File System Support: FAT 32
Image format: JPEG format
Video format: MP4 Compressed format H.264
TF Card: Support Class 10 Micro TF card, Supreme support 64G. a 10-level Micro
TF Card.
Operation Temperature: 0°C to 40°C
Tips: the above data are the test data of the UDIRC toy lab, for
reference only.
Drone Battery
Capacity: 1500mAh
Voltage: 7.4V
Type of battery: LIPo
Energy: 11.1Wh Net
Weight: about 82g
Charging temperature range: 5°C to 40°C
Transmitter
Operation Frequency: 2.4Ghz
Maximum transmission distance: 300m
Operating Temperature: 0°C to 40°C
Battey: 3.7V, 1200mAh
Mobile device bracket Suitable for smartphones
Charger
Input: 5V z 2A
APP
App Name: UDIGPS
Image transmission system: 5G wife
Real-time image transmission: 720 P@20 fps
Operation System: This software is suitable for mobile phones in the IOS 9.0
or later and Android 4.4 or later system,
Tips: the above data are the test data of the UDIRC toy lab, for reference
only.
Troubleshooting
| Problem | Problem cause | Solution |
|---|---|---|
| The controller Indicator lights off. | Low battery. | Charge the drone battery. |
| The batteries are incorrect. | Install the batteries following the polarity |
indicators.
The batteries are incorrectly positioned.| Clean the dirt between the battery
and the battery contacts.
Failed to pair the drone with the controller.| The indicator light is off.|
The same as above.
There is an interfering signal nearby.| Restart the drone and power on the
controller.
Mis-operation.| Operate the drone step by step in accordance with the user
manual.
The electronic component is damaged for fierce crash.| To buy spare parts from
local sellers and replace damaged parts.
The drone is under-powered
r can not fly.| The propeller is seriously deformed.| Replace the propeller.
Low battery.| Charge the drone battery.
Incorrect installation propeller.| Install the propeller in accordance with
the user manual.
Motor is damaged.| Replace the motor.
The drone could not hover nd tilts to one side.| Improper Calibration.| Please
refer to the Calibration.
The propeller is serious.| Replace the propeller.
The motor holder is deformed after a violent crash.| Replace the motor holder
parts.
The gyroscope did not reset after a serious crash.| Put the drone on the flat
ground for about 10 minutes or restart the drone to calibrate again.
The drone indicator
ight is off.| Low battery.| Recharge the drone battery.
The battery is expired or over-discharge protection.| Buy a new battery from
the local seller to replace the battery or charge the battery.
Poor contact| Connect and disconnect the battery.
Could not see the picture.| There is an interfering signal nearby.| Practice
and read the cellphone controlling instruction carefully.
The camera is damaged.| Replace Camera.
Hard to control y cellphone.| Not experienced enough.| Practice and read the
cellphone controlling instructions carefully.
Can’t altitude hold.| The propeller is serious.| Replace propeller.
Atmospheric pressure is not stable.| Refer to the “Altitude Hold
Mode”instruction.
Can’t position hold.| Whether the GPS has connected or not.| Search again to
connect the GPS signal.
The optical flow board is damaged.| Please replace a new one.
Searched but could not
find the GPS signal.| The GPS module is damaged.| Please replace a new one.
The GPS module plug is loose.| Please check to see if it’s connected normally.
FCC Note
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC Notice: The equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual.
Modifications not authorized by the manufacturer may void user’s authority to
operate this device. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference. (2) This device must accept any interference
received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This device should be installed and operated with a
minimum distance of 20cm between the radiator & your body.
Manufacturer company: SHANTOU CITY CHENGHAI UDIRC TOYS CO., LTD Manufacture address Guangfcmg Industrial Zone. Guangxi Stmt. Chenghai District
Shanghai City. Guangdong Province. China
Model: U62
Manufacture time:
MADE IN CHINA
Documents / Resources
|
Chenghai Udirc Toys ZKWCY581707001 5.8G WIFI FPV
DRONE
[pdf] User Manual
GPS20060002, ZKWGPS20060002, ZKWCY581707001, 5.8G WIFI FPV DRONE
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>