WORX WX020 20V Cordless Brushless Paint Sprayer Instruction Manual

WX020 20V Cordless Brushless Paint Sprayer

SAFETY AND OPERATING MANUAL
ORIGINAL INSTRUCTIONS

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

TABLE OF CONTENTS
1. SAFETY INSTRUCTIONS 2. COMPONENT LIST 3. TECHNICAL DATA 4. NOISE INFORMATION 5. VIBRATION INFORMATION 6. CONTROLS AND FUNCTIONS 7. INTENDED USE 8. OPERATING INSTRUCTIONS 9. NOZZLE AND PRESSURE SELECTION 10. CLEANING 11. STORAGE 12. TROUBLESHOOTING

and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

13. DECLARATION OF CONFORMITY

3. Personal safety

a) Stay alert, watch what you are doing and use

1. SAFETY INSTRUCTIONS

common sense when operating a power tool. Do not use a power tool while you are tired

PRODUCT SAFETY GENERAL SAFETY

SVYRHIVXLIMRYIRGISJHVYKWEPGSLSPSV medication. A moment of inattention while
operating power tools may result in serious

WARNINGS

TIVWSREPMRNYV] F
9WITIVWSREPTVSXIGXMZIIUYMTQIRX%P[E]W

2

WARNING Read all safety warnings,

wear eye protection. Protective equipment

MRWXVYGXMSRWMPPYWXVEXMSRWERHWTIGMGEXMSRW

such as dust mask, non-skid safety shoes, hard

provided with this power tool. Failure to follow

hat, or hearing protection used for appropriate

all instructions listed below may result in electric

GSRHMXMSRW[MPPVIHYGITIVWSREPMRNYVMIW

WLSGOVIERHSVWIVMSYWMRNYV]

c) Prevent unintentional starting. Ensure the

Save all warnings and instructions for future

switch is in the off-position before connecting

reference.

to power source and/or battery pack, picking

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-

up or carrying the tool. Carrying power tools [MXL]SYVRKIVSRXLIW[MXGLSVIRIVKMWMRK

operated (cordless) power tool.

power tools that have the switch on invites

accidents.

1. Work area safety

d) Remove any adjusting key or wrench before

a) Keep work area clean and well lit. Cluttered or

turning the power tool on. A wrench or a key left

dark areas invite accidents.

attached to a rotating part of the power tool may

b) Do not operate power tools in explosive

VIWYPXMRTIVWSREPMRNYV]

atmospheres, such as in the presence of

e) Do not overreach. Keep proper footing and

EQQEFPIPMUYMHWKEWIWSVHYWXPower tools create sparks which may ignite the dust or

balance at all times. This enables better control of the power tool in unexpected situations.

fumes.

f) Dress properly. Do not wear loose clothing or

c) Keep children and bystanders away while operating a power tool. Distractions can cause

jewellery. Keep your hair and clothing away from moving parts. 0SSWIGPSXLIWNI[IPPIV]SV

you to lose control.

long hair can be caught in moving parts.

g) If devices are provided for the connection of

2. Electrical safety

dust extraction and collection facilities, ensure

a) Power tool plugs must match the outlet. Never

these are connected and properly used. Use of

modify the plug in any way. Do not use any

dust collection can reduce dust-related hazards.

adapter plugs with earthed (grounded) power

L
(SRSXPIXJEQMPMEVMX]KEMRIHJVSQJVIUYIRXYWI

tools. 9RQSHMIHTPYKWERHQEXGLMRKSYXPIXW

of tools allow you to become complacent and

will reduce risk of electric shock.

ignore tool safety principles. A careless action

b) Avoid body contact with earthed or grounded

GERGEYWIWIZIVIMRNYV][MXLMREJVEGXMSRSJE

surfaces, such as pipes, radiators, ranges

second.

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

4. Power tool use and care

GSRXEGXEGGMHIRXEPP]SGGYVWYWL[MXL[EXIV-J

a) Do not force the power tool. Use the correct

PMUYMHGSRXEGXWI]IWEHHMXMSREPP]WIIOQIHMGEP

power tool for your application. The correct

help. 0MUYMHINIGXIHJVSQXLIFEXXIV]QE]GEYWI

TS[IVXSSP[MPPHSXLINSFFIXXIVERHWEJIVEXXLI

irritation or burns.

rate for which it was designed.

e) Do not use a battery pack or tool that is

b) Do not use the power tool if the switch does not

HEQEKIHSVQSHMIH(EQEKIHSVQSHMIH

turn it on and off. Any power tool that cannot

batteries may exhibit unpredictable behaviour

be controlled with the switch is dangerous and

VIWYPXMRKMRVIITPSWMSRSVVMWOSJMRNYV]

must be repaired.

J
(SRSXITSWIEFEXXIV]TEGOSVXSSPXSVI

c) Disconnect the plug from the power source

or excessive temperature.)TSWYVIXSVISV

and/or remove the battery pack, if detachable,

temperature above 130 °C may cause explosion.

from the power tool before making any

g) Follow all charging instructions and do not

adjustments, changing accessories, or storing

charge the battery pack or tool outside

power tools. Such preventive safety measures

XLIXIQTIVEXYVIVERKIWTIGMIHMRXLI

reduce the risk of starting the power tool

instructions. Charging improperly or at

accidentally.

XIQTIVEXYVIWSYXWMHIXLIWTIGMIHVERKIQE]

d) Store idle power tools out of the reach of

HEQEKIXLIFEXXIV]ERHMRGVIEWIXLIVMWOSJVI

children and do not allow persons unfamiliar

with the power tool or these instructions

6. Service

to operate the power tool. Power tools are

E
,EZI]SYVTS[IVXSSPWIVZMGIHF]EUYEPMIH

dangerous in the hands of untrained users.

repair person using only identical replacement

e) Maintain power tools and accessories. Check

parts. This will ensure that the safety of the

for misalignment or binding of moving parts,

power tool is maintained.

breakage of parts and any other condition

b) Never service damaged battery packs. Service

that may affect the power tool’s operation. If

of battery packs should only be performed

damaged, have the power tool repaired before

by the manufacturer or authorized service

use. Many accidents are caused by poorly

providers.

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

SPRAY GUN SAFETY WARNINGS

3

g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

1. Know your sprayer. Read and understand the operator’s manual and observe the warnings ERHMRWXVYGXMSRPEFIPWEIHXSXLIXSSP
2. Do not use commercial grade chemicals
or chemicals for commercial or industrial purposes. Use only consumer grade waterbased lawn and garden chemicals. (SRSXTSYVLSXSVFSMPMRKPMUYMHWMRXSXLIXERO These can weaken or damage the hose or tank.
4. Do not use caustic (alkali) self-heating or GSVVSWMZIEGMH
PMUYMHWMRXLMWWTVE]IV These

5. Battery tool use and care
   E
   6IGLEVKISRP][MXLXLIGLEVKIVWTIGMIHF] the manufacturer. A charger that is suitable for SRIX]TISJFEXXIV]TEGOQE]GVIEXIEVMWOSJVI when used with another battery pack.
   F
   9WITS[IVXSSPWSRP][MXLWTIGMGEPP] designated battery packs. Use of any other FEXXIV]TEGOWQE]GVIEXIEVMWOSJMRNYV]ERHVI
   c) When battery pack is not in use, keep it away
   from other metal objects, like paper clips,
   coins, keys, nails, screws or other small metal
   objects, that can make a connection from one terminal to another. Shorting the battery XIVQMREPWXSKIXLIVQE]GEYWIFYVRWSVEVI H
   9RHIVEFYWMZIGSRHMXMSRWPMUYMHQE]FI

can corrode metal parts or weaken the tank and hose.
5. Know the contents of the chemical being
sprayed. Read all Material Safety Data Sheets
(MSDS) and container labels provided with the chemical. Follow the chemical manufacturer’s safety instructions.
6. Do not attempt to modify this product or create
accessories not recommended for use with this product. %R]WYGLEPXIVEXMSRSVQSHMGEXMSR is misuse and could result in a hazardous condition leading to possible serious personal MRNYV] (SRSXWTVE]EQQEFPIQEXIVMEPERHER] material where the hazard is not known.

ejected from the battery; avoid contact. If

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

SAFETY WARNINGS FOR

SYMBOL

BATTERY PACK

a) Do not dismantle, open or shred cells or battery

pack.

b) Do not short-circuit a battery pack. Do not store

battery packs haphazardly in a box or drawer

where they may short-circuit each other or be

short-circuited by conductive materials. When

battery pack is not in use, keep it away from

SXLIVQIXEPSFNIGXWPMOITETIVGPMTWGSMRWOI]W

REMPWWGVI[WSVSXLIVWQEPPQIXEPSFNIGXWXLEX

can make a connection from one terminal to

another. Shorting the battery terminals together

QE]GEYWIFYVRWSVEVI

G
(SRSXITSWIFEXXIV]TEGOXSLIEXSVVI

Avoid storage in direct sunlight.

d) Do not subject battery pack to mechanical

shock.

e) In the event of battery leaking, do not allow

XLIPMUYMHXSGSQIMRXSGSRXEGX[MXLXLIWOMR

or eyes. If contact has been made, wash the

affected area with copious amounts of water

and seek medical advice.

f) Keep battery pack clean and dry.

g) Wipe the battery pack terminals with a clean

dry cloth if they become dirty.

h) Battery pack needs to be charged before use.

Always refer to this instruction and use the

4

correct charging procedure.

i) Do not maintain battery pack on charge when

not in use.

j) After extended periods of storage, it may

be necessary to charge and discharge the

battery pack several times to obtain maximum

performance.

O
6IGLEVKISRP][MXLXLIGLEVKIVWTIGMIH

by Worx. Do not use any charger other than

XLEXWTIGMGEPP]TVSZMHIHJSVYWI[MXLXLI

IUYMTQIRX

l) Do not use any battery pack which is not

HIWMKRIHJSVYWI[MXLXLIIUYMTQIRX

m) Keep battery pack out of the reach of children.

n) Retain the original product literature for future

reference.

S
6IQSZIXLIFEXXIV]JVSQXLIIUYMTQIRX[LIR

not in use.

p) Dispose of properly.

U
(SRSXQMGIPPWSJHMJJIVIRXQERYJEGXYVI

capacity, size or type within a device.

r) Keep the battery away from microwaves and

high pressure.

8SVIHYGIXLIVMWOSJMRNYV]YWIV must read instruction manual
Warning

Wear ear protection

Wear eye protection

Wear dust mask

Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem. Do not dispose of waste batteries as unsorted municipal waste.

Do not burn

Li-I on

Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.
Li-Ion battery. This product has been marked with a symbol relating to `separate collection’ for all battery packs and battery pack. It will then be recycled or dismantled in order to reduce the impact on the environment. Battery packs can be hazardous for the environment and for human health since they contain hazardous substances.
Make sure the battery is removed prior to changing accessories.

Wear protective gloves

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

7

1
6 2

4

5

3

8

5

10

13

1.5 1.8 2.2 2.6

9

11

20V Cordless Brushless Paint Sprayer

12
WX020 WX020.X

A1
A3
6

A2 2 1
A4

B1

B2

1 3

2

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

B3

C1

2 1
15

2 1

C2 3

C3 5
7
4

D1

D2

2

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

E

F

NARROW

WIDE

G1
8
G3

100% 0%

G2

H
15-20cm

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

I1

I2

1

2

I3

J1

1/2

9

J2

J3

1

20V Cordless Brushless Paint Sprayer

2
WX020 WX020.X

J4

K1

K2

K3

10

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

2. COMPONENT LIST

SPRAY WIDTH LEVER

AIR CAP

LIQUID CONTAINER

TRIGGER

VOLUME KNOB

LOCK ON/OFF DIAL

AIR FLOW CONTROL

BATTERY PACK*

FILLING CUP

10. WIRE BRUSH

11. DECLOGGING NEEDLE

12. NOZZLE*

13. GARDEN HOSE ADAPTER

14. AIR CAP EAR(SEE FIG. C1)

*Not all the accessories illustrated or described are included in standard delivery.

3. TECHNICAL DATA
Type Designation WX020 WX020.X (020-designation of machinery, representative of battery operated Paint Sprayer)

Rated voltage Maximum pressure Color viscosity

WX020 WX020.X** 20 V Max*** 20 KPa 300 Din-s

Spray color volume
Volume of the container Machine weight (bare tool)

KQMRQQRS^^PI
1000 ml 0.98 kg

** X=1-999, A-Z, M1-M9 there are only used for different customers, there are no safe relevant changes between these models. *** Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts.

SUGGESTED BATTERIES AND CHARGERS

Category

Type

Capacity

20V Battery

WA3014

4.0 Ah

20V Charger

WA3880

2.0 A

We recommend that you purchase your accessories from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.

4. NOISE INFORMATION

A weighted sound pressure A weighted sound power KpA& KwA Wear ear protection.

LpA: 74,6 dB(A) LwA: 85,6 dB(A)
3 dB(A)

5. VIBRATION INFORMATION

Vibration emission value: ah!QW2

11

9RGIVXEMRX]/!QWs

The declared vibration total value and the declared noise emission value have been measured in accordance with a standard test method and may be used for comparing one tool with another. The declared vibration total value and the declared noise emission value may also be used in a preliminary assessment of exposure.

WARNING: The vibration and noise emissions during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used especially what kind of workpiece is processed dependant on the following examples and other variations on how the tool is used: How the tool is used and the materials being cut or drilled. The tool being in good condition and well maintained. The use of the correct accessory for the tool and ensuring it is sharp and in good condition. The tightness of the grip on the handles and if any anti vibration and noise accessories are used. And the tool is being used as intended by its design and these instructions.

This tool may cause hand-arm vibration syndrome

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

MJMXWYWIMWRSXEHIUYEXIP]QEREKIH
WARNING: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not EGXYEPP]HSMRKXLINSF8LMWQE]WMKRMGERXP]VIHYGI the exposure level over the total working period. Helping to minimise your vibration and noise exposure risk. Always use sharp chisels, drills and blades. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate). If the tool is to be used regularly then invest in anti vibration and noise accessories. Plan your work schedule to spread any high vibration tool use across a number of days.
6. CONTROLS AND
FUNCTIONS

Air cap ear %HNYWXXLIWTVE]TEXXIVR by turning the air cap ears. Horizontal pattern (up and down’ spraying motion) Vertical pattern (side to side’ spraying motion )
7. INTENDED USE
Interior and exterior painting and staining of decks, outdoor furniture, fences, and walls
8. OPERATING INSTRUCTIONS
NOTE: Please read the instructions carefully before use.
ASSEMBLY AND OPERATION

Volume knob 7IXXLIPMUYMHS[F]

ACTION

FIGURE

turning the volume knob BEFORE OPERATION

on the trigger of the

12

sprayer %MVS[GSRXVSP

LMUYMHTVITEVEXMSR – Stir the spraying liquid thoroughly. – Unscrew the container . – Fill the liquid container to desired level when the liquid has been appro-

See Fig. A1, A2,A3,A4

8LIEMVS[GERFI

priately thinned**** and strained.

EHNYWXIHJVSQF] XYVRMRKXLIEMVS[ control.

Turbine assembly
NOTE :4VIWWERHXYVRPSGOSRSJJHMEP clockwise to lock on during operation.

See Fig. B1

NARROW

WIDE

Trigger Pull the trigger to deliver spray liquid from the liquid container to the nozzle assembly, where it is sprayed.
Spray Width Lever The spray width lever determines the width of the spray pattern.

Suction tube assembly – Tube end should be facing toward the front of nozzle if spraying downward – Tube end should be facing toward the rear of nozzle if spraying upward

See Fig. B2

Container assembly NOTE: Make sure the container is XMKLXIRIHVQP]

See Fig. B3

LMUYMH*PS[WIXXMRK

Selecting the right nozzle according to
your work Use the srewdriver(not supplied) to take out the nozzle and replace it with the right one according to your work. NOTE :The smaller the diameter of nozzle is,the more delicate work it can deal with.

See Fig. C1,C2,C3

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

Setting the volume -Turn the volume knob on the trigger clockwise to increase the volume. -Turn the volume knob on the trigger counter-clockwise to decrease the volume.
AHNYWXMRKXLIEMVS[ 8YVRXLIEMVS[GSRXVSPJVSQ according to your work .

See Fig. D1
See Fig. D2

Spray pattern adjustment

Adjusting spray shape -Horizontal pattern (up and down’ spraying motion) – Vertical pattern(side to side’spraying motion)

See Fig. E

Adjusting spray width -Wide pattern (for spraying large surfaces) -Narrow pattern(For spraying smaller areas, corners and edges)

See Fig.F

OPERATION

Checking the battery charge condition NOTE: Fig. G1 only applies for the battery pack with battery indicator light.
Charging the battery pack
Installing the battery pack
Press the trigger

See Fig. G1
See Fig. G2
See Fig. G3

USER TIPS

1. Position the tool 15-20cm from the spray surface, depending upon the spray pattern size desired .Spray parallel to the surface with smooth passes at a consistent speed.
%TTP]EXLMRPE]IVSJPMUYMHSRXLIVWX pass and allow to dry before applying a second, slightly heavier coat. 3. It is recommended to partially pull
XVMKKIVVWXMRSVHIVXSWXEVXXLIXYVFMRI before a spray pass is made.

See Fig. H

***It is not necessary for most liquids when used with the nozzle of larger diameter. For use with the nozzle of smaller diameter , thinning may be needed
XSEGLIMZIERIVRMWL-JXLMRRMRKMWRIGIWWEV]YWI XLIPPMRKGYTXSEHNYWXEW]SYRIIH7IIMK%

20V Cordless Brushless Paint Sprayer

13
WX020 WX020.X

9. NOZZLE AND PRESSURE SELECTION
See table for recommended spray pressure for your PMUYMH

-RXIVMSV7XEMRW Interior &
Exterior Clears

Exterior Solid Stains

Speed control

1-5

6-10

Nozzles size

1.5 mm(White)

1.8 mm(Black)

2.2 mm(Red)

2.6 mm(Blue)

Liquids

Primers 6-10

Enamels

Interior Exterior Latex

Latex Paints

Paints

6-10

6-10

6-10

10. CLEANING
NOTE: When cleaning, use appropriate cleaning solutions (warm, soapy water for latex liquids ; mineral spirits for oil-based liquids ).
(1) QUICK CLEANING WITH GARDEN HOSE (FOR WATER PAINT ONLY) (SEE FIG. I1 ,I2,I3) Remove the battery pack and container.Assemble the garden hose adapter to the tool. Connect one end of 14 the garden hose to the adapter and another end to the waterspout.Press the trigger for quick cleaning. Cleaning the color residues after usage non water paints
(2) CLEANING THE COLOR RESIDUES AFTER USAGE NON WATER PAINTS UNIT FLUSHING (SEE FIG. J1, J2, J3,J4) 6IQSZIXLIFEXXIV]TEGO*SVVIPMIZMRKER]TVIWWYVIPIJXSZIVMRXLIXSSPPSSWIRXLIGSRXEMRIVF]XYVRFYXRSX completely remove it . Pull the trigger so that the liquid inside the nozzle drains back into the container.Unscrew the container and remove. Empty any remaining liquid back into the liquid bucket.Pour a small amount of the appropriate cleaning solution into the container.Assemble the container and install the battery pack.Spray the cleaning solution into a safe area. Remove the battery pack. Follow the same instructions to relieve any pressure.
(3) SUCTION TUBE AND NOZZLE CLEANING(SEE FIG. K1, K2, K3) Remove the battery pack.Unscrew the nut and remove the air cap and nozzle.Use declogging needle to clean the nozzle and wire brush to clean suction tube.

11. STORAGE
Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.

ENVIRONMENTAL PROTECTION
Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

FOR BATTERY TOOLS
The ambient temperature range for the use and storage of tool and battery is 0°C-45°C. The recommended ambient temperature range for the charging system during charging is 0°C-40°C

12. TROUBLESHOOTING

Issue

Causes

Solutions

Little or no Liquid S[

1. Nozzle clogged. 2. Suction tube clogged. 3. LiquidS[WIXWXSSPS[ 5. Suction tube loose. 6. No pressure builds up in container. 7. Spray Liquid is too thick.

1. Clean. 2. Clean. 3. Increase LiquidS[WIXXMRK 5. Remove and replace as tightly as possible. 6. Tighten container. 7. Thin****.

Liquid is leaking

1. Nozzle loose. 2. Nozzle worn. 3. Liquid build-up on air cap and nozzle

1. Tighten. 2. Replace. 3. Clean.

Spray pattern is too thick, runs and sags

1.LiquidS[WIXWXSSLMKL 3. Applying too much Liquid. 4. Nozzle is clogged. 6. Too little pressure builds up in container. 7. Spray Liquid is too thick.

1. Decrease LiquidS[WIXXMRK %HNYWX0iquidS[SVMRGVIEWI movement of spray gun. 5. Change. 6. Tighten container. 7. Thin****.

7TVE]NIXTYPWEXIW

1. Liquid in container runs out.

6IPP

15

Too much overspray

1. Gun is too far from spray SFNIGX

1. Reduce distance (15 cm ­ 20 cm is ideal).

Pattern is very light and spotted

1. Moving the spray gun too fast. 2. LiquidS[WIXXMRKXSSPS[

%HNYWX0iquidS[SVHIGVIEWI movement of spray gun.
2. Increase LiquidS[WIXXMRK

13. DECLARATION OF CONFORMITY
We, Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany
On behalf of Positec declare that the product Description Battery operated Paint sprayer Type Designation WX020 WX020.X (020designation of machinery, representative of paint sprayer) Function spraying paint
Complies with the following Directives: 2006/42/EC, 2014/30/EU, 2011/65/EU&(EU)2015/863

Standards conform to EN 62841-1, EN 50580, EN 55014-1, EN 55014-2

8LITIVWSREYXLSVM^IHXSGSQTMPIXLIXIGLRMGEPPI

Name

Marcel Filz

Address Positec Germany GmbH

Postfach 32 02 16, 50796 Cologne, Germany

Allen Ding
(ITYX]’LMIJ)RKMRIIV8IWXMRK
‘IVXMGEXMSR Positec Technology (China) Co., Ltd 18, Dongwang Road, Suzhou Industrial Park, Jiangsu 215123, P. R. China

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

DECLARATION OF CONFORMITY
We, Positec (UK & Ireland) Ltd., PO Box 6242, Newbury, RG14 9LT, UK

On behalf of Positec declare that the product Description Battery operated Paint sprayer Type Designation WX020 WX020.X (020-
designation of machinery, representative of paint
sprayer) Function spraying paint

Complies with the following Directives: Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility Regulations 2016 The Restriction of the Use of Certain Hazardous 7YFWXERGIWMR)PIGXVMGEPERH)PIGXVSRMG)UYMTQIRX Regulations

Standards conform to BS EN 62841-1, BS EN 50580, BS EN 55014-1, BS EN 55014-2

8LITIVWSREYXLSVM^IHXSGSQTMPIXLIXIGLRMGEPPI

Name

Jim Kirkwood

Address Positec (UK & Ireland) Ltd.,

PO Box 6242, Newbury, RG14 9LT, UK
16

Allen Ding
(ITYX]’LMIJ)RKMRIIV8IWXMRK
‘IVXMGEXMSR Positec Technology (China) Co., Ltd 18, Dongwang Road, Suzhou Industrial Park, Jiangsu 215123, P. R. China

After-sales Service and Application
At www.worx.com you can order spare parts or arrange the collection of a product in need of servicing or repair. Tel. Service: 0345 202 9679 E-Mail: customerservices@worxtools.com
www.worx.com
Copyright © 2022, Positec. All Rights Reserved. AR01606502

20V Cordless Brushless Paint Sprayer

WX020 WX020.X

References

• Lawn & Garden Equipment | Innovative Power Tools | WORX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>