EMTEK EMTouch and EMTouch Classic Style Electronic Lever Locksets Installation Guide

June 3, 2024
Emtek

EMTEK EMTouch and EMTouch Classic Style Electronic Lever Locksets Installation Guide
EMTEK EMTouch and EMTouch Classic Style Electronic Lever
Locksets

What’s in the Box

What’s in the Box

ITEM NO. DESCRIPTION QTY
1 Key 2
2 Outside Trim Plate Assembly 1
3 Latch for 23/8” or 23/4” Backset 1
4 Inside Trim Plate Assembly 1
4a Inside Chassis 1
4b Inside Trim Plate 1
4c #8-32 x 3/8″ Flat Head Machine Screw 2
4d 9V Alkaline Battery 1
5 #8-32 x 11/2″ Flat Head Machine Screw 2
6 #8 x 3/4″ Wood Screw 4
7 Strike Plate 1
8 Plastic Extender 1

Preparation

Confirm Handing EN

HANDING OF DOOR IS ALWAYS DETERMINED FROM THE OUTSIDE

Preparation

Preparation

How to Install

Install Latch

Fasten Latch using two #8 x 3/4” Wood Screws (item #6).

Remove Screws from Inside Trim Plate

Use a Phillips head screwdriver to remove screws (item #4c) shown below and detach Inside Trim Plate from the Inside Chassis.

Use a Phillips head screwdriver to remove screws (item #4c) shown below and detach Inside Trim Plate from the Inside Chassis.

How to Install

Install Outside Trim Plate Assembly

STEP 1

While holding Outside Trim Plate Assembly, Press the Plastic Extender (A) into end of Spindle Shaft (B). The Shaft is properly aligned when the marking ‘TOP’ can be seen from an overhead view.

How to Install

STEP 2

Position the Outside Trim Plate Assembly through the bore hole.

How to Install

STEP 3

With the Outside Trim Plate Assembly flush to the door, REMOVE the Plastic Extender.

Install Inside Chassis

STEP 1

Confirm the position of Cam Link.

Install Inside Chassis 

STEP 2

Feed the Wire Harness through Inside Chassis.

Install Inside Chassis 

STEP 3

Fasten Inside Chassis using two #8-32 x 11/2” Flat Head Machine Screw (item

5).

Install Inside Chassis 

STEP 4

Connect Wire Harness (A) and tuck Connectors as shown (B)

Install Inside Chassis 

STEP 5

Install Battery.

Install Inside Chassis 

Install Inside Trim Plate

Fasten Inside Trim Plate using two#8-32 x 3/8” Flat Head Machine Screws (item

4c).

Install Inside Trim Plate 

Neutral position is required for installation and removal of the Inside Trim Plate Assembly.
(Does not apply to Keypad Storeroom/Gate product)

Install Inside Trim Plate 

How to Use

Your Lock is Ready to Use

Your Emtek lock is shipped with two 4-digit user codes and a 6-digit programming code.
These codes are randomly generated at the factory.
(Turn to next page for Programming Instructions.)

To Unlock

  1. Press EMTEK key or touch 3 fingers across screen.

  2. Enter 4-digit user codes.
    (See sticker located on the inside trim plate or back cover page).

  3. Turn Handle.

Passage Feature

(Does not apply to Keypad Storeroom/Gate product)

Activate by turning the inside thumbturn to the unlocked position. This will engage the outside lever so a code is not required to enter.

To Lock

Rotate Thumbturn from inside.

How to Program

Programming Your Lock

In order to perform each of the following six functions, the lock must first be placed in Programming Mode:

  1. Press and hold EMTEK button for 3 seconds
  2. Yellow LED flashes, then remains solid*, number keys also illuminate
  3. Enter Programming Code
  4. Yellow LED flashes, then 2 beeps
  5. Yellow LED remains solid (awaiting button press; see following table)
If You Wish To Press Button Actions Indicators

Change Programming Code

(6 digits)

| 1| Enter New Programming Code (6 digits)| Re-Enter New Programming Code

(6 digits)

| •  1 Green LED flash
•  1 beep
•  1 Green LED flash
•  1 beep
•  2 Green LED flashes
•  2 beeps
Add User Code (4 digits)

(Store up to 20 User Codes)

| 2| Enter New User Code

(4 digits)

| Re-Enter New User Code

(4 digits)

| •  1 Green LED flash
•  1 beep
•  1 Green LED flash
•  1 beep
•  2 Green LED flashes
•  2 beeps
Delete User Code| 3| Enter User Code to be Deleted| Re-Enter User Code to be Deleted| •  1 Green LED flash
•  1 beep
•  1 Green LED flash
•  1 beep
•  2 Green LED flashes
•  2 beeps
Enable/Disable All User Codes| 4| Entering ‘4’ disables all Users (enables all if disabled)| •  2 Green LED flashes
•  2 beeps
Delete All User Codes|
5| Re-Enter Programming Code| •  1 Green LED flash
•  1 beep
•  2
Green LED flashes
•  2 beeps
Turn Beeper On/Off|
6| Entering ‘6’ turns OFF (or ON)| •  1 Green LED flash
•  1 beep
•  2
Green** LED flashes
•  2 beeps

*If no input within 20 seconds, Yellow LED goes out, Red LED flashes and lock exits Programming Mode.
**Also referred to as “vacation mode”. This command temporarily disables all user codes (metal key override will still work).

Keypad Operation – Beeper & LED Indicators 

Function Indicators
Valid Code •   1 short beep, EMTEK button flashes Green.
Invalid Code/Access Denied* •  1 Red LED flash

•   2 short beeps
Lock-Out Mode Error| •  2 short beeps
•  1 short beep per second for duration
Access Accepted| •  1 short beep
•  1 Green LED flash
Low Battery| •  4 Red LED flashes
•  4 short beeps
Blackout Battery| •  1 long Red LED flash
•  4 long beeps
Button Press Accepted| •  1
Yellow LED flash
•  1 Short Beep
Outside Thumb Turn Enabled| •  2
Green** LED flashes

  • If 3 consecutive incorrect codes are entered, the lock emits 4 short beeps and a flashing Red EMTEK button. The lock will not accept additional input for 20 seconds (20 beeps). When the next valid code is entered the lock will beep quickly 3 times to alert of the incorrect codes.
    ** Battery voltage has dropped too low; keypad will be disabled but metal key override will still work.

Restoring the Lock to Factory Default Setting

This procedure clears the lock of all users and restores the Programming Code and 2 User Codes shipped with the lock.

  • Press and hold EMTEK button for 3 seconds.
  • Enter “000000”
  • After 2 beeps and 2 Green LED Flash, remove power (disconnect 9V battery) from Lock.
  • After 5 seconds, restore power (reconnect 9V battery).
  • Confirm by 2 beeps and 2 Green LED Flash.

U.S. patents:
8,176,761
8,141,400

Canadian patents:
2,698,041
2,789,278
2,789,280

Copyright © Emtek Products, ASSA ABLOY Residential Group Inc. DBA Emtek Products, 2021
Reproduction in whole or in part without the express written permission of Emtek Products is prohibited.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Emtek User Manuals

Related Manuals