Einhell TE-RH 950 5F Hammer Drill Instruction Manual

TE-RH 950 5F
Original operating instructions
Hammer drill Art.-Nr.: 42.579.78 I.-Nr.: 21011

TE-RH 950 5F Hammer Drill

Danger!
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due careKeep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating  nstructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 9)

1. Danger! – Read the operating instructions to reduce the risk of injury.
2. Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!
4. Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.
5. Select between the individual functions only when the equipment is at a standstill. If you fail to observe this point, the equipment may be damaged.

Safety regulations

The corresponding safety information can be found in the enclosed booklet. Danger! Read all safety regulations and instructions. Any errors made in following the safety regulations and instructions may result in an electric shock, fi re and/or serious injury. Keep all safety regulations and instructions in a safe place for future use.

Layout and items supplied

2.1 Layout (Fig. 1)

1. SDS-Plus drill chuck

2. Locking sleeve

3. Selector switch for drill/impact drill/chisel
   (knob)

4. On/Off switch

5. Locking button

6. Additional handle

7. Depth stop

8. Handle

9. Speed controller (setting ring)

10. Clockwise/Counter-clockwise switch

11. Quick-change drill chuck

2.2 Items supplied
Please check that the article is complete as specifi ed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suff ocating!

• Hammer Drill
• Additional handle
• Depth stop
• Quick-change drill chuck
• SDS-Plus drill chuck
• Original operating instructions
• Safety information

Proper use

The tool is designed for drilling with hammer action in concrete, rock and brick, as well as for chiseling work, always using the respective correct drill or chisel bit. The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse.
The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Technical data

Mains voltage: ……………………220-240 V ~ 50 Hz
Power input: ………………………………………. 950 W
Idling speed: ……………………..0-1200/0-2600 rpm
Blow rate: …………………………………… 0-4500 rpm
Drilling capacity in concrete/stone (max.): 28 mm
Protection class: …………………………………….II /
Weight: ……………………………………………….3.8 kg
Danger!
Sound and vibration Sound and vibration values were measured in accordance with EN 60745.
LpAsound pressure level …………………… 93 dB(A)
KpA uncertainty ……………………………………… 3 dB
LWA sound power level …………………… 104 dB(A)
KWA uncertainty ……………………………………… 3 dB
The hammer drill is not designed for outdoors use as specifi ed I Article 3 of Directive 2000/14/
EC_2005/88/EC.
Wear ear-muff s.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions) determined in accordance with EN 60745.
Hammer drilling in concrete
Vibration emission value ah = 16.4 m/s²
K uncertainty = 1.5 m/s²
Chiseling
Vibration emission value ah = 13.9 m/s²
K uncertainty = 1.5 m/s²
The specifi ed vibration value was established in accordance with a standardized testing method. It may change according to how the electric equipment is used and may exceed the specifi ed value in exceptional circumstances.
The specifi ed vibration value can be used to compare the equipment with other electric power tools.
The specifi ed vibration value can be used for initial assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

Caution!
Residual risks Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in  onnection with the equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vib- rations if the equipment is used over a prolonged period or is not properly guided and maintained.

Before starting the equipment

Before you connect the equipment to the mains supply make sure that the data on the rating plate are identical to the mains data.
Warning!
Always pull the power plug before making adjustments to the equipment.
Check the drilling point for concealed electrical cables, gas and water pipes using a cable/pipe detector.
5.1 Additional handle (Fig. 2 – Item 6) For safety reasons you must only use the hammer drill with the additional handle.
The additional handle (6) enables you to achieve better stability whilst using the hammer drill. The machine must not be used without the additional handle (6) for safety reasons. The additional handle (6) is secured to the hammer drill by a clamp. Turning the handle anticlockwise (looking from the handle) will release the clamp. Turning the  andle clockwise will tighten the clamp. First  release the additional handle clamp.You can then swing the additional handle (6) into the most comfortable working position for
you. Now turn the additional handle in the opposite direction again until the additional handle is secure.
5.2 Fitting and adjusting the depth stop (Fig. 3/Item 7)
The depth stop (7) is held in place by the additional handle (6) by clamping.

• Release the locking screw (a) and insert the depth stop (7).
• Set the depth stop (7) to the same level as the drill bit.
• Pull the depth stop back by the required drilling depth.
• Retighten the locking screw (a).
• Now drill the hole until the depth stop (7) touches the workpiece.

5.3 Changing the drill chuck (Fig. 4)
You can choose between the quick-change drill chuck (11) and the SDS-Plus drill chuck (1).
Warning:
Always pull out the power plug before making adjustments to the equipment.
Fitting:

• Pull back and hold the locking sleeve (2).
• Turn and push the dust-free drill chuck into the mount.
• Allow the locking sleeve (2) to slide back to its starting position again.
• Check the lock by pulling the drill chuck.

Removing:

• Pull back and hold the locking sleeve (2).
• Remove the drill chuck.

5.4 Inserting the tool (Fig. 5-6)
Warning:
Always pull out the power plug before making adjustments to the equipment.
Note:
Release the depth stop as described in 5.2 and push it towards the additional handle. This provides free access to the chuck.
5.4.1 Quick-change drill chuck (Fig. 5 / Item 11)

• Open the chuck (11). The drill bit opening must be large enough to hold the drill bit.
• Select a suitable drill bit. Push the drill bit as far as possible into the chuck opening.
• Close the chuck (11). Check that the drill bit is secure in the chuck (11).
• Check at regular intervals that the drill bit or tool is secure.

5.4.2 SDS-Plus drill chuck (Fig. 6 / Item 1)

• Clean the tool before fitting it and apply a thin coating of bit grease to the tool shaft.
• Turn and push the dust-free tool into the tool mounting as far as it will go. The tool will lock automatically.
• Check that the bit is locked in placed by pulling on it.
  To remove it, pull back and hold the locking sleeve (b) and remove the tool.

Operation

Danger
To prevent all danger, the machine must only be held using the two handles (6/8). Otherwise there may be a risk of suff ering an electric shock if you drill into cables.
6.1 ON/OFF switch (Fig. 7/Item 4)

• First fit a suitable drill bit into the tool (see 5.4).
• Connect the mains plug to a suitable socket.
• Position the drill in the position you wish to

To switch on:
Press the ON/OFF switch (4)
Continuous operation:
Secure the ON/OFF switch (4) with the locking button (5).
To switch off :
Press the ON/OFF switch (4) briefl y.
6.2 Adjusting the speed (Fig. 7/Item 4)

• You can infinitely vary the speed whilst using the tool.

• Select the speed by applying a greater or lesser pressure to the ON/OFF switch (4).

• Select the correct speed: The most suitable speed depends on the workpiece, the type of use and the drill bit used.

• Low pressure on the ON/OFF switch (4): Lower speed

• Greater pressure on the ON/OFF switch (4):
  Higher speed

• Tip: Start drilling holes at low speed. Then increase the speed in stages.

Benefi ts:

• The drill bit is easier to control when starting the hole and will not slide away.
• You avoid drilling messy holes (for example in tiles).

6.3 Preselecting the speed (Fig. 7/Item 9)

• The speed setting ring (9) enables you to define the maximum speed. The ON/OFF switch (4) can only be pressed to the defined maximum speed setting.
• Set the speed using the setting ring (9) on the ON/OFF switch (4).
• Do not attempt to make this setting whilst the drill is in use.

6.4 Clockwise/Counter-clockwise switch (Fig. 7/Item 10)

• Change switch position only when the drill is at a standstill!
• Switch the direction of the hammer drill using the clockwise/counter-clockwise switch (10):

Direction
Clockwise (forwards and drill)
Counter-clockwise (reverse)
Switch position
Pushed in to the right Pushed in to the left
6.5 Drill / Hammer drill / Chisel selector switch (Fig. 8)

• For drilling, press the button (E) on the rotary switch (3) and simultaneously turn the rotary switch (3) to position A. Switch position A1:
  High torque, low speed Switch position A2: Low torque, high speed

• For drilling, press the button (E) on the rotary switch (3) and simultaneously turn the rotary switch (3) to position A.

• For hammer drilling, press the button (E) on the rotary switch (3) and simultaneously turn the rotary switch (3) to position B.

• For chiseling, press the button (E) on the rotary switch (3) and simultaneously turn the rotary switch (3) to position C. In switch position C the chisel is not ocked.

• For chiseling, press the button (E) on the rotary switch (3) and simultaneously turn the rotary switch (3) to position D. The chisel is locked in position D.

Notice
Only low pressure is required for hammer drilling.
Excessive pressure will exert an unnecessary force on the motor. Check the drill bits at regular intervals. Sharpen or replace blunt drill bits.

Replacing the power cable

Danger!
If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.

Cleaning, maintenance and ordering of spare parts

Danger!
Always pull out the mains power plug before starting any cleaning work.
8.1 Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

8.2 Carbon brushes
In case of excessive sparking, have the carbon brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep laced by anyone but a qualifi ed electrician.
8.3 Maintenance
There are no parts inside the equipment which require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering replacement parts:

• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required
  For our latest prices and information please go to www.Einhell- Service.com

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offi ces.

Storage

Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG. Subject to technical changes
Service information
We have competent service partners in all countries named on the guarantee certifi cate whose contact details can also be found on the guarantee certifi cate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

• Not necessarily included in the scope of delivery!
  In the eff ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com.
  Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

  • Did the equipment work at all or was it defective from the beginning?
  • Did you notice anything (symptom or defect) prior to the failure?
  • What malfunction does the equipment have in your opinion (main symptom)?
    Describe this malfunction.

Warranty certifi cate

Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not aff ected by this guarantee. Our guarantee is free of charge to you.
2. The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectifi cation of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee: – Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance. – Damage to the device caused by abuse or incorrect use (for example overloading the device.
4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fi tted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fi tted. This also applies if an on-site service is used.
5. To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identifi cation will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.

Of course, we are also happy off er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address. Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.
Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article

Declaration of conformity

We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom declare the conformity to UK standards and legislation was assessed for:

References

• Einhell Service
• Einhell Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>