Einhell TE-MG 300 EQ Oscillating Multi Tool Instruction Manual

: October 27, 2023
: Einhell

Table of Contents

Einhell TE-MG 300 EQ Oscillating Multi Tool
Safety regulations
Layout and items supplied
Proper use
Technical data
Before starting the equipment
- Triangular sanding/grinding plate
Operation
Replacing the power cable
Cleaning, maintenance, and ordering of spare parts
Disposal and recycling
Storage
Service Information
Warranty certiﬁ cate
Documents / Resources

Einhell TE-MG 300 EQ Oscillating Multi Tool

Einhell -TEMG300-EQ-Oscillating-Multi-Tool-product

Danger! – Read the operating instructions to reduce the risk of inquiry
Caution! Wear ear-muﬀ s. The impact of noise can cause damage to hearing.
Caution! Wear a breathing mask. Dust that is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!

Danger!
When using the equipment, a few safety pre-cautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the in-formation is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Safety regulations

The corresponding safety information can be found in the enclosed booklet.
Warning!
Read all the safety information, instructions, illustrations, and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, ﬁ re, and/or serious injury. Keep all the safety information and instructions in a safe place for future use.

Layout and items supplied

Layout (Fig. 1)

ON/OFF switch
Tool chuck
Dust extraction adapter
Speed controller
Quick-release lock for changing tools 6a. Dust extraction device 6b. Fastening clip
Scraper
Delta grinding/sanding disk
Plunge-cut saw blade for wood
Bi-metallic plunge-cut saw blade
Segmented saw blade (HSS)
Segmented saw blade for tile joints
Abrasive paper
Disk

Items supplied
Please check that the article is complete as speciﬁ ed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

Open the packaging and take out the equipment with care.
Remove the packaging material and any packaging and/or transportation braces (if available).
Check to see if all items are supplied.
Inspect the equipment and accessories for transport damage.
If possible, please keep the packaging until the end of the guarantee period.

Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. There is a danger of swallowing or suﬀ locating!

Multifunction tool
Triangular sanding/grinding plate
Scraper
Plunge-cut saw blade for wood
Bi-metallic plunge-cut saw blade
Segmented saw blade (HSS)
Segmented saw blade for tiles
6x abrasive paper
Dust extraction adapter
Dust extraction device
Disk
Original operating instructions
Safety instructions

Proper use

The equipment is designed for the sanding/grinding of wood, iron, plastic, and similar materials using the appropriate sanding/grinding paper. Furthermore, the equipment is intended for sawing wood, plastic, and similar materials, as well as scraping oﬀ glued carpets, ﬁlling compound residues, old paint, and similar applications. The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade, or industrial applications. Our warranty will be voided if the machine is used in commercial, trade, or industrial businesses or for equivalent purposes.

Technical data

Mains voltage: ……………….. .. 230-240 V ~ 50 Hz
Power input: ……………………………………… 300 W
Idling speed: ………………….. .. 11000-20000 rpm
Sanding/grinding area: ………. 90 x 90 x 90 mm
Oscillation angle:… ……………………………… 3,2°
Protection class :………………………………….. II/IQ
Weight:.. …………………………………………. 1.83 kg

Danger!
Sound and vibration Sound and vibration values were measured in accordance with EN 62841.

LpA sound pressure level.. ………………. 78 dB(A)
KpA uncertainty …………………………………….. 3 dB
LWA sound power level ………………….. 89 dB(A)
KWA uncertainty. …………………………………… 3 dB

Wear ear-muﬀ s.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions) determined in accordance with EN 62841.
Handle
Vibration emission value ah = 2,277 m/s2
K uncertainty = 1.5 m/s2
The stated vibration emission levels and stated noise emission values were measured in accordance with a set of standardized criteria and can be used to compare one power tool with another. The stated vibration emission levels and stated noise emission values can also be used to make an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary from the level speciﬁ ed during actual use, depending on the way in which the power tool is used, especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a minimum.

Only use appliances that are in perfect working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Has the appliance been serviced whenever necessary?
Switch the appliance off when it is not in use.
Wear protective gloves.

Caution! Residual risks
Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be ruled out. The following hazards may arise in connection with the equipment’s construction and layout:

Lung damage if no suitable protective dust mask is used.
Damage to hearing if no suitable ear protectionism is used.
Health damage is caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Before starting the equipment

Before you connect the equipment to the mains supply make sure that the data on the rating plate is identical to the mains data.
Warning!
Always pull the power plug before making adjustments to the equipment.

Fitting the plug-in tools (Figures 1/2/3)

Open the quick-release lock for changing tools (5) as shown in Fig. 2.
To fit the plug-in tools safely you should hold the multifunction tool so that the On/Off switch (1) points down and the tool chuck (2) faces up.
Place the plug-in tool (e.g. the scraper) on the tool chuck (2) so that the pins of the tool chuck fit into the recesses in the plug-in tool. The tool chuck (2) is magnetic in order to secure the plug-in tool during the clamping procedure.
Close the quick-release lock for changing tools (5) again. Take care that the pins of the chuck (2) remain in the recesses in the plug-in tool.
The equipment comes with a disk (14) for safely securing plug-in tools with recesses. Please note the correct use (camber facing the tool) of the disk (14) for plug-in tools with recess as shown in Fig. 8 and 9.

Check that the plug-in tool is secure.

Triangular sanding/grinding plate

Fit the triangular sanding/grinding plate to use the equipment as a delta sander/grinder. Fastening the sanding/grinding paper Easy replacement using hook-and-loop fastening. Make sure that the vacuum extraction holes on the sanding/grinding paper and the sanding/grin-ding disk are aligned.
Fitting the dust extraction device
(Fig. 4/5/6) The dust extraction device prevents the accumulation of dirt and high dust loads in the air, and it makes it easier to dispose of the dust.

Open the quick-release lock for changing tools and place the equipment in a stable po-sition as described in 5.1.
Mount the dust extraction device (6a) on the tool chuck (2) as shown in Fig. 4.
Fasten the dust extraction device (6a) with the fastening clip (6b) by latching it in the air vents of the equipment as shown in Fig. 5.
Connect the extractor adapter (3) to the dust extraction device (6a). Make sure that the ar-row (A) on the extractor device coincides with the recess (B) on the dust extraction device (6a) (see Fig. 5). Turn the extractor adapter (3) anti-clockwise until it engages..
Connect your tool to an extraction unit or va-cuum cleaner. This will provide excellent ext-raction of chips and dust from the workpiece.

The beneﬁ ts are that you will protect both the equipment and your own health. Your work area will also be clean and safe.

Operation

Switching on/oﬀ
Slide the switch (1) forwards to switch on the equipment. Slide the switch (1) to the rear to switch on the equipment.
Practical tips

Switch on the equipment.
Work away from the body.
Never move your hands into the direct vicinity of the work area.
Use only plug-in tools which are in good working order and undamaged.

Plug-in tools
Sawing: Sawing wood and plastic.
Notes on working practice: When sawing, watch out for foreign bodies in the workpiece and remove these if necessary. Plunge cutting is allowed only in soft materials such as wood or plasterboard.
Sanding/grinding: Surface sanding/grinding at edges, in corners, or in hard-to-reach areas. Depending on the choice of sanding/grinding paper for the sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice: This equipment oﬀ ers particularly high performance for the sanding/ grinding of hard-to-reach corners and edges. To sand/grind proﬁ les and channels you can also work with just the tip or the edge of the sanding/grinding disk. Various sanding/grinding papers
are available, specially designed for the diﬀ recent types of material you may be working on and the amount you wish to remove from the surface. The amount removed will depend largely on the choice of sanding/grinding paper and the pressure applied to the sanding/grinding disk.
Scraping: Scraping oﬀ old paint or adhesives. Notes on working practice: Move the plug-in tool against the area you want to remove. Begin with a ﬂ at an angle of incidence and little pressure. The surface (e.g. wood, plaster) may be damaged if too much pressure is used.

Speed control (Fig. 7) You can select the speed by turning the speed controller (4).

Plus direction: Higher speed
Minus direction: Lower speed

Replacing the power cable

Danger!
If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.

Cleaning, maintenance, and ordering of spare parts

Danger!
Always pull out the mains’ power plug before starting any cleaning work.
Cleaning

Keep all safety devices, air vents, and motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
We recommend that you clean the device immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

Carbon Brushes
In case of excessive sparking, have the carbon brushes checked only by a qualiﬁ ed electrician. Danger! The carbon brushes should not be replaced by anyone but a qualiﬁ ed electrician.
Maintenance
There are no parts inside the equipment which require additional maintenance.

Ordering spare parts and accessories.
Please provide the following information when ordering spare parts:

Type of unit
Article number of the unit
ID number of the unit
Spare part number of the required spare part For our latest prices and information please go to www.Einhell-Service.com
Tip! For good results, we recommend high-quality accessories! www.kwb.eu welcome@kwb.eu

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your
local council oﬃ ces.

Storage

Store the equipment and accessories in a dark and dry place at an above- freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.

For EU countries only
Never place any electric power tools in your household refuse. To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taken to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers ac-companying products, is permitted only with the express consent of Einhell Germany AG. Subject to technical changes

Service Information

We have competent service partners in all countries named on the guarantee certiﬁ cate whose contact details can also be found on the guarantee certiﬁ cate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Category	Example
Wear parts*	Carbon brushes, Triangular sanding/grinding plant, Scraper, HSS

saw blade, Diamond saw blade
Consumables*| Grinding/sanding paper
Missing parts|

Not necessarily included in the scope of delivery!

In the eﬀect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

Did the equipment work at all or was it defective from the beginning?
Did you notice anything (symptom or defect) prior to the failure?
What malfunction does the equipment have in your opinion (main symptom)? Describe this malfunction.

Warranty certiﬁ cate

Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not aﬀ ected by this guarantee. Our guarantee is free of charge to you.
he warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectiﬁ cation of said defects on the product or the replacement of the product, whichever we prefer.
Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
The following are not covered by our guarantee:
Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.
Damage to the device caused by abuse or incorrect use (for example overloading the device or the use of unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts ﬁtted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts ﬁtted. This also applies if an on-site service is used.
To make a claim under the guarantee, please register the defective device at:
www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identiﬁ cation will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.

Of course, we are also happy oﬀ er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units that are no longer covered. To take advantage of this service, please send the device to our service address. Also refer to the restrictions of this warranty concerning wear parts, consumables, and missing parts as set out in the service information in these operating instructions.

Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article
2014/29/EU
2005/32/EC_2009/125/EC
(EU)2015/1188
2014/35/EU
2006/28/EC
X 2014/30/EU
2014/32/EU
2014/53/EU
2014/68/EU
(EU)2016/426
Notified Body:
(EU)2016/425
X 2011/65/EU_(EU)2015/863
X 2006/42/EC
Annex IV
Notified Body:
Reg. No.:
2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured LWA = dB (A); guaranteed LWA = dB (A)
P = kW; L/Ø = cm
Notified Body:
2012/46/EU_(EU)2016/1628
Emission No.:
Standard references: EN 62841-1; EN 62841-2-11; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN 62321
First CE: 16 Archive-File/Record: NAPR025883
Art.-No.: 44.651.50 I.-No.: 21021 Documents registrar: Christoph Egger
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
Multifunction tool

Documents / Resources

| Einhell TE-MG 300 EQ Oscillating Multi Tool [pdf] Instruction Manual
TE-MG 300 EQ, Oscillating Multi Tool, Multi Tool, Oscillating Tool, Tool
---|---