ULINE H-992 MONARCH 1135 Two Line Label Gun Instructions
- June 7, 2024
- ULINE
Table of Contents
H-992
MONARCH 1136
TWO LINE LABEL GUN
INSTRUCTIONS
CHANGING THE INK ROLLER
-
Pull the latches back and swing the cover open completely. You should hear a click.
NOTE: Do not force the cover past the click position. -
Hold the labeler sideways over a trash can while pushing the button to release the ink roller. (See Figure 1)
-
Hold the new ink roller by the stem. (See Figure 2)
-
Slide it onto the post, snapping it into place. (See Figure 2)
-
Close the cover completely.
SETTING PRINT CHARACTERS
-
Pull the knob until the indicators are on the desired band.
-
Turn the knob until the desired character appears black on a white background between the indicators. To print a blank, select the blank space for that band. (See Figure 3)
-
Repeat steps 1-2 for each band.
-
Push in the knob when you are done.
LOADING LABELS
-
Pull the latches back and swing the cover open completely. You should hear a click. (See Figure 4)
NOTE: Do not force the cover past the click position. -
For loading a new roll of labels, tear off and discard the first 10 inches of label and liner.
-
To prevent jamming, peel the first 12 labels from liner and discard.
-
Place the label roll between the hubs and click into place. (See Figure 5)
NOTE: Do not thread label strip through any rollers. -
Drape the supply across the labeler and center it over the peel bar. The supply should hang out 5-6 inches past the peel bar.
-
Close the cover.
-
Squeeze and hold the trigger while feeding the label strip under the roller and into the large slot above the arrow until it stops/hits the back. (See Figure 6)
-
Hold the strip in place and squeeze the trigger eight times or until the label strip feeds through the rear exit.
-
Remove any loose labels.
CLEARING LABEL JAMS, CLEANING AND LUBRICATION
-
Open the cover and remove the label roll.
-
Remove any loose labels from the inside of the labeler. (See Figure 7)
-
Pull up on the supply guide to expose the backing paper path and remove loose labels. (See Figure 8)
-
Snap the supply guide back into place.
-
Use a commercial adhesive solvent to clean adhesive buildup.
-
Remove the ink roller to expose the print bands and brush them off with a toothbrush.
-
Reload, then close the cover.
CHARACTER KEY
Regular Font (3 MM) 1st Line
KNOB POSITION
1| 2| 3| 4| 5| 6| 7| 8
.| .| .| .| .| .| .| .
1| 1| 1| 1| 1| 1| 1| 1
2| 2| 2| 2| 2| 2| 2| 2
3| 3| 3| 3| 3| 3| 3| 3
4| 4| 4| 4| 4| 4| 4| 4
5| 5| 5| 5| 5| 5| 5| 5
6| 6| 6| 6| 6| 6| 6| 6
7| 7| 7| 7| 7| 7| 7| 7
8| 8| 8| 8| 8| 8| 8| 8
9| 9| 9| 9| 9| 9| 9| 9
0| 0| 0| 0| 0| 0| 0| 0
$| $| $| $| $| $| +TX| +TX
WAS| WAS| WAS| WAS| WAS| WAS| ,| ,
FOR| FOR| FOR| FOR| FOR| FOR| OFF| OFF
C| C| C| C| C| C| EA| EA
/| /| /| /| /| /| 1/2| 1/2
–| –| –| –| –| –| |
KNOB POSITION
1| 2| 3| 4| 5| 6| 7| 8
1| 1| 1| .| | 1| 1| LB
2| 2| 2| 1| 1| 2| 2| EACH
3| 3| 3| 2| 2| 3| 3| FOOT
4| 4| 4| 3| 3| 4| 4| YARD
5| 5| 5| 4| 4| 5| 5| DOZ
6| 6| 6| 5| 5| 6| 6| PAIR
7| 7| 7| 6| 6| 7| 7| PKG
8| 8| 8| 7| 7| 8| 8| BOX
9| 9| 9| 8| 8| 9| 9| CASE
0| 0| 0| 9| 9| 0| 0| SET
$| $| $| 0| 0| +TX| +TX| OFF
FOR| FOR| FOR| /| /| EACH| OFF| +DEP
/| /| /| –| –| | | +TX
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>