DELTA IFD6500, IFD6530 USB/RS-485 Communication Interface Instruction Manual

June 3, 2024
Delta

DELTA IFD6500, IFD6530 USB/RS-485 Communication Interface

DELTA IFD6500,
IFD6530 USB-RS-485 Communication Interface-product

Introduction

IFD6500/IFD6530 is a convenient RS-485-to-USB converter, which does not require external power-supply or complex setting process. It supports baud rate from 75 to 115.2kbps and auto switching direction of data transmission. In addition, it adopts RJ-45 in RS-485 connector for users to wire conveniently. And its tiny dimension, handy use of plug-and-play and hot-swap provide more conveniences for connecting all DELTA IABU products to your PC. Applicable Models: All DELTA IABU products.

  • Please thoroughly read this instruction sheet before installation and putting it into use.
  • The content of this instruction sheet and the driver file may be revised without prior notice. Please consult our distributors or download the most updated instruction/driver version at http://www.deltaww.com
Application & Dimension

DELTA IFD6500, IFD6530 USB-RS-485 Communication
Interface-fig-2

Specifications

  • Power supply
    • No external power is needed
  • Power consumption
    • IFD6500: 0.4W;IFD6530: 1.5W
  • Isolated voltage
    • 2,500VDC
  • Baud rate
    • 75, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200 bps
  • RS-485 connector
    • RJ-45
  • USB connector
    • A type (plug)
  • Compatibility
    • Full compliance with USB V2.0 specification
  • Max. cable length
    • RS-485 Communication Port: 100 m
  • Support RS-485 half-duplex transmission

RJ-45DELTA IFD6500, IFD6530 USB-RS-485 Communication Interface-
fig-3

Preparations before Driver Installation

Download the USB driver from our official website
(https://downloadcenter.deltaww.com/en-US/DownloadCenter) and follow the steps below to extract it. Note: DO NOT connect IFD6500/IFD6530 to PC before extracting the driver file.DELTA IFD6500, IFD6530 USB-RS-485
Communication Interface-fig-4DELTA
IFD6500, IFD6530 USB-RS-485 Communication Interface-
fig-5

You should have a folder marked SiLabs under drive C.

Driver Installation

After connecting IFD6500/IFD6530 to PC, please install driver by following steps.DELTA IFD6500, IFD6530 USB-RS-485 Communication Interface-
fig-6DELTA IFD6500, IFD6530 USB-
RS-485 Communication Interface-fig-7 DELTA IFD6500, IFD6530 USB-RS-485 Communication
Interface-fig-8

LED Display

  1. Steady Green LED ON: power is ON.
  2. Blinking orange LED: data is transmitting.
  • IFD6500/IFD6530 is an OPEN-TYPE device. It should be installed in a control cabinet free of airborne dust, humidity, electric shock and vibration. To prevent non-maintenance staff from operating IFD6500/IFD6530 , or to prevent an accident from damaging IFD6500/IFD6530 , the control cabinet in which IFD6500/IFD6530 is installed should be equipped with a safeguard. For example, the control cabinet in which IFD6500/IFD6530 is installed can be unlocked with a special tool or key.
  • DO NOT connect AC power to any of I/O terminals, otherwise serious damage may occur. Please check all wiring again before IFD6500/IFD6530 is powered up. After IFD6500/IFD6530 is disconnected, Do NOT touch any terminals in a minute. Make sure that the ground terminal   on IFD6500/IFD6530 is correctly grounded in order to prevent electromagnetic interference.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals