TOPMAQ DC12V Electric Hoist Instruction Manual

: June 3, 2024
: TOPMAQ

Table of Contents

Safety Precautions
Overview
Installation
OPERATION
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ELECTRIC HOIST DC12V
Assembly & Operating Instructions
Instruction Manual

Safety Precautions

Read the instruction carefully; be familiar with the structure and performance of the machine.
Check the vehicle battery to make sure it’s 12 V /24V DC before power-on.
Make sure all the connecting points of the power and the quick connector are fixed firmly and that they work properly.
Make sure all the points of welding are good before operation.
People are not allowed to stand beneath the crane when it’s working, make sure that they are in the safety area.
Do not violate the operating regulations.
Do leave five wraps of the wire rope on the drum(the part with red color).
The motor of the winch is series wound motor,it’s for intermittent use only,allow the motor to cool down when it’s hot resulting from work.
Never lift or transport people using the crane.

Warning
CHEMICL AND FIRE HAZARD
Failure to observe these instructions could lead to severe injury or death.
Always remove jewelry and wear eye protection.
Never lean over battery while making connections.
Always verify area when drilling is clean of fuel line,fuel tank,brake lines,electrical wires,etc.
Never route electrical cables:
-Across any sharp edges.
-Through or near moving parts.
-Near parts that become hot.
Always insulate and protect all exposed wiring and electrical terminals.
Always install terminal boots as directed in installation instructions.

CAUTION
General Safety:
Always know your winch:Take time to fully read and understand the included Installation and Operation guide,and Basic Guide to Winching Techniques, in order to understand your winch and winching operation.
Never operate this winch if you are under 16 years of age.
Never operate this winch when under the influence of drugs, alcohol or medication.
Never exceed winch or wire rope rated capacity.

Installation Safety:
Always choose a mounting location that is sufficiently strong to withstand the maximum lifting capacity of your crane.
Always use factory approved switches,remote controls,accessories and installation components.
Always use Grade 8.8 or better hardware,never weld bolts and never use longer bolts than those supplied from factory.
To avoid injury to hands or fingers:
Always wear heavy leather gloves when handling a wire rope.
Never let wire rope slip through your hands.

Overview

HP1200 is one of our professional products, with 12 /24 volt DC as the power. It is widely used in pick-up trucks, caravan cars, loading docks, platforms etc. With outstanding features such as structurally compact , small sized, light weighted, and minimal space required, HP1200 is a good helper for lifting goods equal to or less than 800kg weight.

Structure Characteristics
This machine consists of five major parts: column, supporting rack,arm,boom and winch as well as other accessories.
Ball bearings serves as the supporting point for the crane. The user operates the push bar making the boom rotate 360° to finish the job of loading and unloading. Goods can be lifted and lowered with the winch .

Installation

Electrical Installation
The long lines from the control box should be connected to the battery , while short lines connected to the winch motor, with red to positive and black negative.Now you are ready to lift or lower goods by operating the switch according to the arrow indications on the hand-held control.
Crane Installation

A） to install on a vehicle
There are four mounting holes (diameter 15mm)on the base, see picture 2 for detailed dimensions, drill four holes on a level surface of the vehicle,lock up the flat washers,spring washers,bolts and nuts provided to fix the crane on the vehicle.Make sure that the surface that the crane is mounted to is level and that the crane is mounted firmly,otherwise danger or injuries will be invited.
B) to install on the ground
Use expansion bolts to fix the crane base on the ground. Make sure that the surface that the crane is mounted to is level and that the crane is mounted firmly,otherwise danger or injuries will be invited.

OPERATION

Adjust the height and length of the boom according to the characters of the goods and its weight,size,etc,put the pin through the boom and the use the safety pin to secure the boom,screw off the locking bar, press the lowering down arrow on the hand-held switch to spool out the wire rope,hook the goods up and check the packing of the goods,if approved,press the lifting up arrow on the hand-held switch and lift the goods to the height required,operate the push bar to rotate the goods to the place needed and then press the lowering down arrow to put the goods down.
If you need to move the goods from a certain height to a lower place,operate the hand-held switch oppositely.

SPECIFICATIONS

Compact design,folds away when not in use Easily installed,on site or by a vehicle body builder

CAUTION:
ALWAYS REPLACE DAMAGED WIRE ROPE WITH MANUFACTURER’S IDENTICAL REPLACEMENT PART.TROUBLESHOOTING

SYMPTOM	POSSIBLE CAUSE	SUGGESTED ACTION
Winch Motor will not operate, or runs in one direction only	-Switch

inoperative
-Broken wires or bad connection
-Defective motor| -Replace switch
-Check for poor connections -Replace or repair motor
Winch Motor runs but drum does not turn| -Clutch not engaged| -Engage clutch
Winch Motor runs but with insufficient power or line speed| -Weak battery -Defective motor| -Recharge or replace battery. -Check battery terminals for corrosion. Clean as required. -Check and clean connections -Repair or replace motor
Winch Motor overheating| -Winch running time too long
-Defective motor| -Allow winch to cool down periodically
-Repair or replace motor