PREMIUM LEVELLA DF2-11 Mini Fridge Freezer Owner’s Manual
- June 3, 2024
- PREMIUM LEVELLA
Table of Contents
Service manual
Model: DF2-11 PRF316300HS
Product description
BRAND: | Premium Levella |
---|---|
MODEL: | PRF316300HS |
PRODUCT DESCRIPTION: | Mini Bar, glass shelves, crystal crisper, recessed |
handle
Color| Inox
LOADING QTY/40HQ| 274
PRODUCT DIMENSION (WDH mm)| 480500850
PACKING DIMENSION (WDH mm)| 500540885
PRODUCT WEIGHT (Kg):| Gross Weight (G.W)| Net Weight (N.W)
26| 24
Total Gross Capacity (Cu.Ft)| 87
Total Net Capacity (Cu.Ft)| 85
The cooling system
General exploded view
No. | Homa Code | Description of Spare Part | Quantity |
---|---|---|---|
4 | 20122080036 | Door hinge screw cover | 1 |
5 | 20122080091 | Door hinge cover | 1 |
6 | 3031400148 | Upper door hinge | 1 |
7 | 2208101188 | Middle hinge washer | 1 |
8 | 3031400116 | Middle door hinge | 1 |
9 | 3031400067 | Lower door hinge | 1 |
10 | 2100152587 | Upper door | 1 |
10.1 | 3020400145 | Upper door gasket | 1 |
10.2 | 20122090005 | Right Aid Closer Of Upper Door | 1 |
10.3 | 20122090011 | Left Aid Closer Of Upper Door | 1 |
11 | 2100152588 | Lower door | 1 |
11.1 | 3020400146 | Lower door gasket | 1 |
11.2 | 3031500031 | Door joist, straight | 1 |
11.3 | 3031500044 | Door joist, curved | 1 |
11.4 | 3031500011 | Lower door joist | 1 |
11.5 | 20122090162 | Right Aid Closer Of Lower Door | 1 |
11.6 | 20122090179 | Left Aid Closer Of Lower Door | 1 |
12 | 2501100002 | Door switch | 1 |
13 | 20120020226 | Fridge shelf assembly | 1 |
17 | 3031500055 | Bottle rack for drinks | 1 |
18 | 3020500092 | Upper door joist | 1 |
19 | 2207400523 | Crisper drawer assembly | 1 |
20 | 20120030010 | Cover of crisper drawer | 1 |
21 | 3050100117 | Power supply cord | 1 |
22 | 3039900264 | Compressor bracket | 1 |
25 | 20122990039 | Drain pan | 1 |
26 | 3050200095 | Earthing wire of compressor | 1 |
28 | 2400100282 | Compressor | 1 |
29 | 3040500011 | Drier filter | 1 |
30 | 20114070006 | Connecting tube | 1 |
31 | 3040600005 | Process tube | 1 |
32 | 20120010085 | Thermostat controller | 1 |
32.1 | 2400200005 | Thermostat | 1 |
32.11 | 20122010037 | Thermostat Knob | 1 |
32.3 | 2500500002 | Light Bulb | 1 |
32.5 | 20122010002 | Controller Shell | 1 |
32.6 | 20122010048 | Lamp Cover | 1 |
32.7 | 2500600001 | Light Holder | 1 |
42 | 20122990019 | Higher Leveling Foot | 1 |
--- | --- | --- | --- |
44 | 20122990006 | Shorter Leveling Foot | 1 |
300 | 2700501337 | Trademark | 1 |
301 | 2700117929 | Carton | 1 |
Trouble shooting guide
No | Problem | Possible Cause | What To Do |
---|---|---|---|
**** 1 | **** Refrigerator room temperature Ok and compressor running Fan not |
working
Freezer room temperature not enough cold
No air in the freezer air outlets| the fan motor failure| 1-
Open the cover board of the air duct in the freezer room and check the fan
2- If not running, measure the voltage between the red wire and black wire
of fan
3- If the voltage is 12V, the fan motor is failure and replace it with a new
one
the failure of the inner wire to fan connector| 1- Measure the
voltage between the CN2 red and black wire of PCB
2- If the voltage is 12V, check from the inner wire to fan connector
the PCB failure| 1- Measure the voltage between the CN2 red and
black wire of PCB
2- If the voltage is zero, then the PCB failure and change a new PCB
2| No defrost Freezer room temperature is not cold enough Refrigerator room:
duct and ice formation on the evaporator| the drainpipe contains impurity| 1-
Disconnect power, and let the ice melt and inspect the water if it is flowing
through the drain pipe
2- If not, check if there is impurity and clean the drain pipe
the sensor failure or PCB failure| 1- Check the fuse
2- If the fuse is melted, it means that the sensor failure or PCB failure
3- Change the sensor or PC
the defrost heater is broken or PCB failure| 1- Check the CN4 defrost
heater two connector
2- If the heater is OK then is the PCB failure and change the PCB
3| The temperature of the freezer and refrigerator is not cold
enough
The temperature can not be adjusted by the potentiometer (thermostat)|
the potentiometer failure| 1- Inspect the potentiometer (thermostat)
2- Measure the resistance value by adjusting the potentiometer (thermostat)
3- The resistance value is not changed by adjusting the potentiometer
(thermostat)
the sensor failure| 1- If the potentiometer (thermostat) setting
is below 3 degrees, the compressor will be running 20 minutes and then stop 30
minutes
2- If the potentiometer (thermostat) setting is more than 3 degrees, the
compressor will be running 30 minutes and then stop 20 minutes
3- If the compressor works like the above situation, it means the sensor
failure
4-Open the back of the refrigerator and change the sensor of the refrigerator
evaporator
4| LED light is not working| the led failure| 1- Open the refrigerator
door and measure the voltage of CN3 in the PCB
2- If the voltage is zero then it means the connecting wire failure
3- If the voltage is 12V, it means the led failure
---|---|---|---
the switch circuit failure| 1- If the CN3 voltage is not 12V, then
check the CN4 voltage
2- If the CN4 voltage is not changed by closing and opening the door, it
means the switch circuit failure
5| Compressor not start running| no problem| 1- The time between
two starting is shorter than 12min
2- The refrigerator room temperature is lower than the set temperature
3- In this case, it is no problem. Please wait for longer
PCB failure| PCB has automatic self-examination:
1- Open the cover of PCB at the back of the product, plug-in power and push
the SW101, switch 3 seconds and the PCB begin automatic self-examination
program
2- Then the led, compressor, fan and defrost heater will work for two
seconds and then stop and quit the automatic self-examination program. After
that, the program will reset to the original setting.
3- If the automatic self-examination program is not working, it means the
PCB failure and needed to be changed
**** compressor wire failure or compressor damage| 1- Measure the voltage
of compressor input connector
2- If it is OK then check the starting and relay of the compressor
3- Also check the wire if it is OK
6| Not woeking at all| the PCB failure| **** 1- Check the power
by multimeter
2- If the input voltage is 220V-240V, but the led, compressor, fan, and
defrost heater are all not working, it means the PCB failure and needed to be
changed
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>