PREMIUM LEVELLA PFR33400X Chest Freezer User Manual
- October 30, 2023
- PREMIUM LEVELLA
Table of Contents
Model:PFR33400X/PFR50400X
PFR70400X/PFR10400X
CHEST FREEZER
CONGELADOR HORIZONTAL
User Manual
Use and care manual. Important safeguards. This product is for domestic use only.
Transportation and Placement
△ When transporting the chest freezer from one place to another, the
inclination of the cabinet should not exceed 45 degrees to prevent against
compressor or system damage.
△ Before use, remove all the packing material. The back side of the cabinet
should be more than 20cm away from the wall, both flank sides more than 20cm.
△ The freezer should be put in a well-ventilated, dry place. Do not place it
under direct sunshine. The freezer should be kept away from the water sink,
heat sources and any volatile or corrosive material.
Power source and test-running
△ Specified capacity of the wire is 7A. Section squares of the wire is
0.82mm². Single line or compound lines are all allowed. A fuse of 2.5A
specified electric current should be installed. (Power cord should be replaced
with the same of 7A and 0.82mm2 if it is damaged).
△ Single-phase power supply, 60Hz, voltage range 98~132V. If the voltage is
unstable, please install a voltage stabilizer with capacity above 1000W.
△ Avoid turning the power on and off too frequently. If the power is turned
off, wait an interval of 5 minutes before turning it on again.
△ When the freezer is going to be out of use for a long time, disconnect the
power first, remove all its contents and then clean it. Please examine the
circuit whether it is in perfect conditions before reuse.
Operation of the Temperature Control Knob
△ The temperature inside the cabinet can be controlled with the temperature
control knob.
△ The knob should be kept upright normally to adjust the temperature. “7” is
the coldest freezing setting and is suitable for fast freezing. Do not keep
the knob at this point for long.
△ <1=: temperature inside the freezer cabinet is around -10 ℃
△ <2=: temperature inside the freezer cabinet is around -12 ℃
△ <3=: temperature inside the freezer cabinet is around -15 ℃
△ <4=: temperature inside the freezer cabinet is around -18℃ (Factory setting)
△ <5=: temperature inside the freezer cabinet is around -20 ℃
△ <6=: temperature inside the freezer cabinet is around -22 ℃
△ <7=: temperature inside the freezer cabinet is around -25 ℃
Food storage
△ Allow space between the foods stored in the cabinet, and between the foods
and the inner surface of the cabinet to keep good ventilation of cold air and
freeze evenly. Do not put in any bottled or canned beverages with freezing
points above the temperature in the cabinet when it is below zero.
△ For foods that should be moisture-free or lose water easily, wrap them up in
airtight food bags or containers before putting in the cabinet to avoid smell-
mixing and reduce frosting.
△ Storage of volatile and combustible gases, liquids such as strong alkalis,
strong acids, petrol, etc. is not allowed.
Maintenance
△ The freezer should be cleaned regularly. When cleaning, turn off the power,
take out all the food from the cabinet, and clean the inside using water or a
little neutral detergent.
△ Do not use boiling water, acid, chemical diluents, petrol, oil, or dirt-
removing powder.
△ Dry it after cleaning.
△ Use light soap water when cleaning the door seal and apply a little of
talcum powder on it after natural drying to extend its service life.
△ Use a soft cloth with water or a little detergent to clean the exterior
surface.
Note: Keep the power supply and connecting wires away from water to avoid
electric shock.
△ Those who are not a service technician should not take apart and repair the
freezer on their own to avoid additional trouble. Unauthorized repairs of
electrical parts as compressor, temperature controller is forbidden.
Defrosting
△ For better freezing efficiency, defrost when the frost film inside the
cabinet is 4-5mm thick.
△ When defrosting, turn off the power, take out the frozen foods, open the
door for warming and melting. Use a soft cloth to absorb water and clean it
up.
△ Do not use sharp metal tools as steel brushes to clean the frost film when
defrosting to avoid evaporator damage.
Trouble shooting
| Failure | Cause | Removal method |
|---|---|---|
| The indicator is not on. The compressor does not start. | The plug is not | |
| really connected to the socket. | Replug it. | |
| No power | Connect to a socket with power. | |
| The indicator is on, but the compressor does not work and buzzes only | The | |
| power voltage is ＜ 98V. | Install a power-regulator over 1000W. |
The compressor stops a minute after starting, and restarts after a few minutes
repeatedly.| power regulator over The power voltage is > 132V.
The compressor works normally, but the temperature inside the cabinet goes
down too slowly.| The door is opened too frequently.| Reduce door opening
times.
There is too much food inside the cabinet And/ or it is improperly placed.|
Place foods properly keeping space between them for ventilation of cold air.
The frost film is too thick Take thick.| Take out the food and defrost the
freezer.
The surface of the condenser is too dirty.| Stop and clean the condenser.
The door is not sealing.| Adjust the door seal.
The noise is too loud| The freezer not level.| Level the freezer.
The freezer door is loose.| Tighten the door.
There is contact between the back pipes and the exterior walls.| Separate the
pipes from the exterior walls.
The following are not failures:
△ When the freezer is working or after is stops for a while, the refrigerant
in the pipes is cycling and produces <running water= sounds.
△ The surface temperature of the compressor may be up 70℃~80℃ when it is
working.
△ The back side of the freezer gives out heat.
△ In rainy season, the outer surface of the cabinet may have dew, which is not
a defect on normal use. Just dry it with a piece of cloth.
CONTROL PANEL OPTION 1 (A) – THERMOSTAT: regulates the temperature inside
the freezer cabinet.”
(B) – GREEN LED POWER INDICATOR: indicates that the freezer is in operation.
(C) – BLUE LED RUN INDICATOR: indicates that the compressor is in operation.
(D) – RED LED ALARM INDICATOR: indicates that the temperature inside the
freezer cabinet is over -12℃
CONTROL PANEL OPTION 2 (A) – THERMOSTAT: regulates the temperature inside
the freezer cabinet.
(B) – GREEN LED POWER INDICATOR: indicates that the freezer is in operation.
(C) – BLUE LED RUN INDICATOR: indicates that the compressor is in operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>