Sainlogic 10.2 inch large Display Wireless Weather Station User Guide
- June 15, 2024
- Sainlogic
Table of Contents
- Sainlogic 10.2 inch large Display Wireless Weather Station
- Product Information
- Product Usage Instructions
- Weather Server Registration
- WiFi Setup of Display Console
- Install Batteries for Outdoor Sensor Array
- Plug in Adapter for Indoor Console
- Sensors Verification
- Outdoor Integrated Sensor Installation
- Documents / Resources
Sainlogic 10.2 inch large Display Wireless Weather Station
Product Information
Specifications
- Product Name: WiFi Simple Setup Guide
- Compatible Platforms: Weathercloud.net, Wunderground.com
- Wireless Connectivity: WiFi
- Power Source: Adapter and Batteries
Product Usage Instructions
Weather Server Registration Guide
Sign up on Weathercloud.net
- Open a laptop for better user experience.
- Visit the Weathercloud.net website and sign up.
- Fill in all the required fields marked with a red star (*).
- Select any name or model in the Model list and any link type.
- Sign in to Weathercloud with your email and password.
- Click “Get Coordinates” to identify your location.
- Click the “Create” button at the bottom to save and complete.
Sign up on Wunderground.com
- Click “Settings” and select the link.
- Copy and record the Weathercloud ID and Key information.
- Visit the Wunderground.com website and click “Join” button.
- Fill in your email and password.
- Sign in with your email and password.
- Click “My Profile” and select “MY DEVICES” to add new devices.
- Select any model or other in the PWS DropDownList, then click “Next”.
- Select or input your local address.
- Input any name.
- Click “Next”.
WiFi Setup of Display Console
- Plug in the adapter and power up the console.
- Make sure the WiFi icon is flashing.
- Open the WiFi list on your laptop and select WLAN of Sainlogic. (No password is required for this network.)
- If you are unable to connect, check if your firewall stops unfamiliar network connections.
- Once connected, the WiFi word icon on the console should start flashing.
- Click “I Accept” and “Next”.
- Copy and record the station ID and Key.
- Enter the following IP address into any internet browser’s address bar: http://192.168.5.1 (make sure to include the header http://, not just 192.168.5.1).
- Copy and paste ID and key information from Wunderground.com or Weathercloud.net website.
- Fill in all the other blank fields in the table and save.
- Once WiFi connected and data is being uploaded, the WiFi and weather data uploading icons will stay solid.
- Sometimes it may take up to 30 minutes to see the updated data online.
- Click “Save key” and the status display will show the connected IP, indicating that the connection is completed.
- You can now view the data on Wunderground.com or the Weathercloud.net website.
FAQ
Q: How long does it take for the data to be updated online?
A: Sometimes you need to wait about 30 minutes to see the updated data online.
Weather Server Registration
Note : If you have registered the Weathercloud and Wunderground account before, only need to create a “New Device” to add your new weather station information
Sign up on Weathercloud.net
Note : You are advised to register on the laptop for better experiences.
WiFi Setup of Display Console
Note : When powered up the console, If the WiFi is displayed without flashing. Press the Min/Max key for 3 seconds until the WiFi word icon is flashing.
This instruction helps you verify whether the unit is working properly after unboxing.
Install Batteries for Outdoor Sensor Array
Plug in Adapter for Indoor Console
The Console will instantly display indoor information, and Integrated outdoor
sensor data will update on the display within a few minutes. Do not press any
buttons until the outside transmitter reports in, otherwise the outdoor sensor
search mode will be terminated.
When the outdoor transmitter data has been received, the console will
automatically switch to the normal mode from which all further settings can be
performed. While in the search mode, the remote search icon will be constantly
displayed.
Sensors Verification
Put the outdoor sensor array and the indoor console at the same location in good ventilating condition.
- Verify temperature and humidity. The difference between indoor and outdoor temperatures should be within 4°F/2°C. The difference between indoor and outdoor humidity should be within 10%. Usually, the indoor temperature is a little bit higher than the outdoor temperature due to the warming-up effect of the backlight. Let the unit stabilize for at least 30 minutes.
- Verify wind speed and wind direction. Spin the wind cup and the wind vane and make sure the wind speed and wind direction information on display updates.
- Verifying Rain gauge. Tip the sensor array back and forth several times. You should hear a “clicking” sound within the rain gauge. Verify the rain reading on the display console is not reading 0.00. Each “click” represents 0.01 inches of rainfall.
Outdoor Integrated Sensor Installation
Fasten the integrated transmitter to mounting pole brackets with foot- mounting, two ¢3 bolts, and M3 nuts. Tighten the mounting pole to your existing mounting pole with the four¢5 Bolts and M5 Nuts assembly, or fix on the wall with four tapping screws. Please ensure that the outdoor transmitter is fixed particularly tightly, otherwise windy conditions cause the transmitter to shake and thus misread the rainfall data.
Install the sensor array at least four times the distance of the height of the tallest obstruction.
Horizontal Installation
Vertical Installation
Documents / Resources
|
Sainlogic 10.2 inch large Display Wireless Weather
Station
[pdf] User Guide
10.2 inch large Display Wireless Weather Station, 10.2 inch, large Display
Wireless Weather Station, Display Wireless Weather Station, Wireless Weather
Station, Weather Station
---|---
References
- Weathercloud | Global network of weather stations
- Local Weather Forecast, News and Conditions | Weather Underground
- Local Weather Forecast, News and Conditions | Weather Underground