MUSICAL FIDELITY M6x 250.7 7 Channel Power Amplifier Instruction Manual

June 3, 2024
MUSICAL FIDELITY

M6x 250.7 7 Channel Power Amplifier
Instruction Manual

Manual in different languages available from www.musicalfidelity.com

Safety Information

This unit is supplied with a mains lead fitted with a moulded 13-amp plug. If, for any reason, it is necessary to remove the plug, please remove the fuse holder and dispose of  the plug safely, out of reach of children. It must not be plugged into a mains outlet.
The wires in the mains lead supplied with this appliance are coloured in accordance with the following code

Green and yellow ……………………………… Earth
Blue ……………………………………………… Neutral
Brown ………………………………………………….. Live

WARNING – This appliance MUST be earthed.
The colours of the wires of the mains lead of this appliance, may not correspond with the coloured markings identifying the terminals in the plug, proceed as follows:

  • The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or coloured green or green-and-yellow, or  by the earth symbol:
  • The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
  • The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
  • If connecting to a BS1363 plug, a 13-amp fuse must be used.

Precautions & User Information
WARNING: Any modifications to this product, not expressly approved by Musical Fidelity, who is the party responsible for standards compliance could void the user’s  authority to operate this equipment.

This new M6x 250.7 is designed and built to provide trouble-free performance. As with all electronic devices it is necessary to observe a few precautions:

  • Heed all warnings shown on the back of the product.
  • Only connect the M6x 250.7 to a mains outlet having the same voltage as marked at the back of the unit.
  • Always ensure that when disconnecting and reconnecting your audio equipment the mains supply is switched off.
  • Position the mains lead and signal interconnects where they are not likely to be walked on or trapped by items placed on them.
  • Do not use near water, or place water-filled containers on the M6x 250.7, for example, a flower vase or potted plants. If water does spill inside, immediately pull out the  mains plug from the wall socket and inform the dealer, who should then check the unit before further use. Entry of liquid into the M6x 250.7 is dangerous and may  cause electric shock or fire hazard.
  • Do not place the unit near direct heat sources such as radiators, direct sunlight or other equipment.
  • Do not remove any covers or try to gain access to the inside. There are no user adjustments or fuses to change without qualification. Refer all service work to an  authorized Musical Fidelity agent.

Note: Unauthorized opening of the equipment will invalidate any warranty claim.
The electronics in modern hi-fi equipment are complex and may, therefore, be adversely affected or damaged by lightning. For protection of the audio system during  electrical storms, remove the mains plugs. If after-sales service is required, to help the dealer identify the M6x 250.7please quote the serial number located on the rear  panel of the unit.

Installation

Introduction
This unit has been designed for maximum performance. The M6x 250.7 easily powers your speakers at high levels and allows you to fully enjoy audio and video sources with  great dynamics.
Note: In normal operation, the unit dissipates a small quantity of power at all times, and it is important that it is adequately ventilated. The M6x 250.7 must be protected  from humidity – if the unit is moved from a cold place to a warm room, leave the unit for an hour or so to allow sufficient time for the moisture to evaporate.
Cleaning
Before cleaning the unit, switch off power at the mains switch and remove the mains plug from the wall socket. Clean the cabinet and remote-control unit using a moist cloth.  Using solvents, white spirit or thinners is not advised, as they could damage the surface finish.
Installation
Position the M6x 250.7 on a stable, horizontal surface where there is no risk of it being knocked or subjected to vibration such as from loudspeakers.
Power Connections
The M6x 250.7 is supplied with a standard IEC mains cable which plugs into the IEC socket at the back of the unit.
Audio Output Connections
RCA output: If you want to use two modules to bi-amplify speakers, or would like to bi-amplify using another power amp, you can use this output to feed another amp  module or amplifier with the same signal.
Speaker outputs: The speaker output terminals for each channel are located below the XLR inputs. The top terminal of each channel is the positive (red) output and connects  to the positive input of your speaker. The bottom terminal of each channel is the negative (black) output and connects to the negative input of your speaker. The terminals  accept naked wire, spade connectors or banana plugs.
Input connections
UNBALANCED RCA input: One unbalanced RCA input is available for each amplifier channel.
Connect this to the corresponding RCA output of your preamplifier.
BALANCED XLR input: One balanced XLR input is available for each amplifier channel. Connect this to the corresponding XLR output of your preamplifier. If you have  XLR outputs on your preamplifier, use these whenever possible.
Balanced connections offer many advantages compared to unbalanced connections.
Interconnects
Note: Musical Fidelity currently do not make any  interconnecting cables other than those supplied with the unit. If necessary, please refer to the dealer who can advise on  quality cables for any particular setup..

Standard XLR Balanced input/output lead connections:

(for reference only, no XLR signal leads supplied)

Pin functions:

  1. Ground, 0V
  2. Normal polarity (“hot” or “+”)
  3. Inverted polarity (“cold” or “-”)

Facilities & Connections

  1. Power/Standby button and LED’s
    Turns the unit on or off. You can also use the trigger input to automatically turn on your M6x 250.7. It will turn on when an external source provides 5-30V on the  trigger input.

  2. Status LEDs for each channel
    Blue LEDs: device is turned on and ready
    Red LEDs: fault condition: Overheated, short circuit, DC on outputs
    Dimmed red LEDs: standby mode is active

1 RCA Analogue input 5 Trigger ON/OFF
2 RCA Analogue output (through) 6 Trigger IN/OUT
3 XLR Balanced input 7 Power ON/OFF switch
4 Speaker output 8 Mains IEC socket

Troubleshooting

Problem Probable Cause Remedy
No power Power plug is not inserted into socket correctly. Plug in securely

into unit’s IEC socket.
Excessive hum from system speakers.| Audio connector plug not fully pushed in. Cable Fault. Unsuitable Cable (e.g. cable grounds not connected).| Insert plug securely. Check cable is connected at both ends. Some “esoteric” cables have internal wiring intentionally disconnected/modified. For best results on all inputs, please use good quality screened coax; signal and screen directly connected both ends.
Amplifier will not turn on| Power switch not in ON position
Power mode switch in wrong position| Check the power switch on the back & put it in ON position Check the power mode switch.

Technical Specifications

Output
Output power
Output power peak THD+N
Frequency Response SNR| 7x 250W/4 ohms 7x 400W/4 ohms 0,003% at 100W power output
20Hz – 20kHz for 0,5dB
105dB at 1kHz at 200W power output
---|---
Connections Line level inputs
Line level outputs| 7 line level RCA
7 line level XLR (balanced)
7 line level RCA through outputs
Power requirement Mains voltages
Consumption| 230V/115V Internally set or 100V optional. AC 50/60Hz 2500W, 0,5W standby
Weight
Unit only, unboxed
In shipping carton & inc. accessories| 32,5 kg ca. 35 kg
Unit dimensions
Wide
High, including feet
Deep (front to back) including terminals| 450 mm
195 mm
435 mm

Musical Fidelity reserves the right to make improvements which may result in specification or feature changes without notice.

Item Disposal Information for Europe

DISPOSAL
The crossed out wheeled bin label that appears on the back panel of the product indicates that the product must not be disposed of as normal household waste. To prevent  possible harm to the environment please separate the product from other waste to ensure that it can be recycled in an environmentally safe manner. Please contact your local  government office or your retailer for available collection facilities.

a Division of Audio Tuning
Vertriebs GmbH
Margaretenstrasse 98
A-1050 Vienna
AUSTRIA
+43 1 544 858 0400
http://www.musicalfidelity.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MUSICAL FIDELITY User Manuals

Related Manuals