HQ POWER VDLPS36 Series PIN SPOT User Manual

HQ POWER VDLPS36 Series PIN SPOT

Introduction

To all residents of the European Union

Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised company for recycling. This device should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.
Thank you for buying the VDLPS36B / VDLPS36C! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don’t install or use it and contact your dealer.

Safety Instructions

• Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
• Do not touch the device during operation as the housing heats up.
• Keep this device away from rain and moisture.
• Unplug the mains lead before opening the housing.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
• A qualified technician should install and service this device.
• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device against damage by leaving it switched off until it has reached room temperature.
• This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified person carry out the electric connection.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
• If the external power cord of this device is damaged, it shall exclusively be replaced by the manufacturer, service agent, or qualified technician in order to avoid hazards.
• CAUTION – Hot lamp!
• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.
• There may be some smoke or a particular smell when the device is activated for the first time. This is normal and any smoke or smell will gradually disappear.
• Do not look directly at the light source as sensitive people may go into an epileptic seizure if they do.
• Note that damage caused by user modifications to the device is not covered by the warranty.
• Keep the device away from children and unauthorised users.

General Guidelines

• This device is designed for professional use on stage, in discos, theatres, etc. The VDLPS36B / VDLPS36C should only be used indoors with an alternating current of max. 230VAC / 50Hz.
• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Select a location where the device is protected against extreme heat (see “Technical Specifications”), dust and moisture. Respect a minimum distance of 0.5m between the device’s light output and any illuminated surface.
• Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).
• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified people. Any damage that may occur will most probably be due to the unprofessional use of the device.
• Use the original packaging if the device is to be transported.
• All modifications of the device are forbidden for safety reasons.
• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, crashes, etc. Using the device in an unauthorised way will void the warranty.

Installation

Lamps

• Only fit or replace a lamp when the device is unplugged from the mains.
• Let a lamp cool down before replacing it as the temperature of a lamp can reach 700°C during operation.
• When handling a halogen lamp, do not touch it with your bare hands. Use a cloth to insert or remove it.
• Do not install lamps with a higher wattage. They get hotter than this device was designed for.
• Replace any deformed or damaged lamp with a lamp of the same type (see “Technical Specifications”):
  1. Pull the extension spring and open the housing.
  2. When replacing a lamp, unplug the lamp socket and remove the old lamp.
  3. Insert the lamp in the housing.
  4. Fix the socket and close the device.

Remark: Do not operate the device when the cover is open.

Mounting the Device

• Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.
• The construction to which the device is attached should be able to support 10 times the weight of the device for one hour without deformation.
• The installation must always be secured with a secondary attachment e.g. a safety cable (e.g. VDLSC7 or VDLSC8).
• Never stand directly below the device when it is being mounted, removed, or serviced. Have a qualified technician check the device once a year and once before you bring it into service.
• Install the device in a location with few passers-by that is inaccessible to unauthorised persons.
• Overhead mounting requires extensive experience: calculating workload limits, and determining the installation material to be used. Have the material and the device itself checked regularly. Do not attempt to install the device yourself if you lack these qualifications as improper installation may result in injuries.
• Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
• Make sure there is no flammable material within a 0.5m radius of the device.
• Have a qualified electrician carry out the electric connection.
• Connect the device to the mains with the power plug. Don’t connect it to a dimming pack.
• The installation has to be approved by an expert before the device is taken into service.

Cleaning and Maintenance

1. All screws should be tightened and free of corrosion.
2. The housing, visible parts, mounting supports, and the installation location (e.g. ceiling, suspension, trussing) should not be deformed, modified, or tampered with e.g. do not drill extra holes in mounting supports, and do not change the location of the connections.
3. Moving mechanic parts must not show any signs of wear and tear.
4. The electric power supply cables must not show any damage. Have a qualified technician maintain the device.
5. Disconnect the device from the mains prior to maintenance activities.
6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
7. There are no user-serviceable parts.
8. Contact your dealer for spare parts if necessary.

Technical Specifications

• Power Supply max. 230VAC / 50Hz
• Lamp LAMP36 (30W / 6.4V, not incl.) or LAMP36GE (30W / 6.4V, not incl.)
• Dimensions 115 x 160
• Total Weight 1.1kg

For more info concerning this product, please visit our website www.hqpower.com. The information in this manual is subject to change without prior notice.

References

• Details – Own brands – Velleman – Wholesaler and developer of electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>