hp 3179276 Backup Keys Hardware Mounting Kit Instruction Manual
- June 3, 2024
- HP
Table of Contents
- Box Contents
- Warning
- Disclaimers:
- Battery Installation
- Master Code Programming
- Programming the Fingerprints
- Delete the Registered Fingerprint
- Low Battery Warning
- Securing Your Safe
- Wire rope installation
- Customer Support/Warranty
- Linked Warranty (Terms and Conditions)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Instruction Manual
Box Contents
- Backup Keys (2)
- Owner’s Manual/Quick Start Guide
- Hardware Mounting Kit
- Wire rope
- External battery
Warning
Neither seller nor manufacturer shall be liable for unauthorized access, any
injury, loss or damage to personal property direct or consequential, arising
out of the use of, or the inability to use the Safe.
The user shall determine the suitability of the Safe before the intended use
and user assumes all risk and liability what soever in connection therewith,
Safe are not intended to protect against environmental hazards including fire
and water.
Be sure and follow all local and state firearm laws.
DO NOT operate a firearm without proper training and experience.
Disclaimers:
Neither seller nor manufacturer shall be liable for unauthorized access, any
injury, loss or damage to personal property direct or consequential, arising
out of the use of, or the inability to use the Safe.
The user shall determine the suitability of the Safe before the intended use
and user assumes all risk and liability what soever in connection therewith,
Safe are not intended to protect against environmental hazards including fire
and water.
Be sure and follow all local and state firearm laws.
DO NOT operate a firearm without proper training and experience.
Battery Installation
-
To get started, remove the key cover (see Figure C), and insert one of your backup keys into the keyhole at the front of the safe. Push key in and rotate the key counterclockwise to open the safe.
-
Remove crate foam insert. Locate the battery compartment door on the inside of the safe directly below the keypad (see Figure D).
-
Open the battery cover and insert the 4 AA alkaline batteries(notincluded)into the batterycompartment.
Note that pay attention to the “+“ and “-“ signs. The “-” end of the batteries go against the spring inside of the compartment. -
After inserting the battery,Place the batteries cover.
You are now ready to program your safe.
IMPORTANT:
- Use the NEW AA alkaline batery. Using other batteries may cause unusable conditions.
- Your safe will automatically lock when you fully close the lid.
Master Code Programming
First time users should change the default code as soon as possible to prevent
unauthorized access to your safe, so it should be kept confidential.
TIP: Code Requirements
- Ifthe password contact’s entered incorrectly 3 times orthe fingerprint is entered incorrectly 5 consecutivetimes, the panel will be locked for 1 minute, the buzzer will alarm for 30 seconds, and all keys/fingerprints will become invalid during the alarm period;
- Note:The buzzeralarms for30 seconds will not be affected bythe silence, but will still sound
- Programming a new code will overwrite your previous code.
- Enter default code 1-2-3-4-# on the keypad to open your safe.
- With the safe open, press and hold the “PROGRAM” button (3 seconds), all keys (1-#) will light up twice with double beep (see Figure E).
- Directly enterthe 3-6 digits of the new password. and press”#”key. If you hear 2 beeps and the green light flashes twice, If the password setting is successful; if you hear 3 beeps and the red light flashes 3 times, the password setting is failed , Please start over from the second step.
Programming the Fingerprints
To Register Your Fingerprint, Locate the “Program” Button.
- With the safe open, press and hold the “PROGRAM” button (3 seconds), all keys will light up once with the one beep(see Figure F).
- Using the helpful programming tips provided on page 6(see Fiure G) place your finger on the fingerprint scanner for the 1st of four scans. Remove your finger after all keys light up GREEN once with one short beep. Place finger again overthe scanner until all keys light up GREEN once with one short beep and Iift.You will repeat this process until all keys light up twice with the double beeps.
- Now your fingerprint has been successfully registered. Close door and test to see if the safe will open using your fingerprint. If you make a mistake and the new fingerprint will not work, you must repeat the above steps.
Note:
- If the entry fails, the buzzer will beep 3 times and the red light will flash 3 times; if no finger is pressed for more than 10 seconds, the buzzer will beep 3 times and the red light will flash 3 times, prompting the entry failure.
- You cannot register more than 20 fingerprints. If the light Iflashes 5 times with 10 beeps when you register once your fingerprint, it means the fingerprint storage capacity is full.
Helpful Programming TIPS:
- Place your finger on the center of the scanner (this allows the scanner to read where most of the fingerprint detail is located).
- Adjust your finger slightly between scans for increased accuracy.
- Excessive moisture, lotions, or dirt will affect your fingerprint and may Cause inaccurate sensor reading.
- If you are experiencing difficulty try different fingers. Each finger is unique, and some fingers such as your thumb, Contain more readable information than others.
- To increase your success rate, please register the same fingerprint multiple times.
Delete the Registered Fingerprint
- Press and hold the program button (5-6 seconds) until all the keys flash twice with double beeps and let go.
- Now all registered fingerprints are erased.(All fingerprint can open)
IMPORTANT
When only flash once with one beep, do not let go. You must hold the program
button until the keys flash twice with double beeps, then release it.
To silence the audible sound of the electronic,hold the”4″button for4seconds
until you hear one beep and all keys will flash together.To unmute the
keys,repeat this step.
Low Battery Warning
If all keys will light up red 10 times with 10 times beeps when opening the
safe by electronic way,your battery level is critically low and your safe
needs to be replaced the 4 new batteries.
IMPORTANT
Use the the NEW AA alkaline battery. Using other batteries may cause unusable
conditions.
Securing Your Safe
There aresome mounting screws included to mountyoursafe to a flat surface
using the pre-drilled holes on the bottom. Using the Mounting Screws
TIP: Make sure you have enough clearance for the lid to open properly
before mounting the safe.
- Position the safe on a flat surface where you want to mount it.
- Use a pencil to mark the holes for drilling.
- Drill pilot holes.
- Position safe in place and install screws through safe into pilot holes. Tighten screws.
IMPORTANT
Mounting the safe vertically so that the door flips upward will result in
incomplete opening of the safe due to weight. The door will open if the safe
is mounted vertically so that door opens down or to side.
Wire rope installation
- With the safe open,
- Take the A pass through the circle B and will form the big circle C, then put the A to the Safe box
- Then close the safe box
Customer Support/Warranty
Customer Support If you have a problem with your safe that is not answered in
the this manual, we encourage you to email us:
nbtao1996@gmail.com We will get back to you
within 24hrs.
Satisfied with us.
Hum, this people is nice, i can give them a positive reviews to tell people
they are selling good products, doing the right thing.
Linked Warranty (Terms and Conditions)
Cu. safe is committed to building high quality products and will make every
effortto ensure our products are free from any defects. We guarantee your safe
will be free of defects in materials or workmanship for a period of one year
from the date of original. This warranty does not cover abuse, misuse, use in
any manner for which is not designed, neglect, modification, damage in
advertently caused by the owner; accidents, and/or tampering.
If you safe is determined to be defective and we are responsible for the cause
we will have it repaired at our expense, or we will send a new replacement at
no cost to you. You will be required to return your existing unit as well as
all included accessories to safe prior to replacement of the defective unit
along with your order of purchase.
If it is determined your safe needs to be returned our customer support team
will provide you with a return detail.
Please have the following information available when contacting US:
- Purchaser’s name and mailing address, email address, and phone number
- Online order number
- Detailed description of problem
NEITHER SELLER NOR MANUFACTURER SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL,ARISING OUT OF THE USE OF,OR THE INABILITY TO USE our SAFE.
Dear Customer
Thank for your business
BEST WISHES FOR YOU
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>