Electric Lint Remover WiredLux Rechargeable User Manual

Electric Lint Remover WiredLux Rechargeable User Manual

Product Overview

Product Model: LINT REMOVER FS-9955A
Rated Voltage: 3.7V
Rated Output: 5W
Input Voltage : 5.OV-1A
Product Size: 182x74x113mm

Help

First, arrange your clothes on a lat surface. Beware of the following material when using your product:

If any abnormalities or defects occur during use, stop immediately.

Caution: This product cannot be used for down or puffer jackets.

1. When cleaning your lint remover, use a cloth dipped in diluted neutral detergent. Gently rub and wipe the product. Do not use gasoline. This may cause product deformation, inflammation or electric shock.
2. Do not charge the lint remover: below 5°C or above 35°C, in direct sunlight, near heating appliances or lights. The product life may bereduced. Fire, electric shock and product distortion may occur.
3. Worn out blades may become dull and cause damage to the fabric. Blades should be replaced within approximately 50 hours of use.

Potential Issues & Solutions

Problem: Product is not working? Solution

See if product is charged properly. 3. Check the blades and propellers for foreign objects. 4. If the product is still not working, please contact customer service at: support@wiredlux.com

Problem: How do I change the blade? Solution:

. Open the mesh cover, and take out the blade. Replace with a spare blade and make sure that the blade is properly attached to the mesh sheet. If the height doesn't match, check and adjust the blade.

Problem: There is no response when charging the machine? Solution:

Please make sure the USD cable is well-stocked. 2. Make sure the charging light is on. 3. If the product is still not charging, please contact customer service at: support@wiredlux.com

Safety Precautions

1. When unplugging the charging cable, pull the head of the charging cable. Never pull the power cable off.
2. Do not insert fingers or metal objects into the grill part of the machine. It can cause product damage or injuries,
3. The edge of the blade is very sharp, please be extra careful when using it.
4. Do not turn on the machine when the mesh cover needs to be removed or installed.
5. Never force the surface of a knife or tap it with a solid object because the edge of the blade is thin.
6. Install the mesh cover and blade correctly. Failure to do so may result in user injury or damage to the blades.
7. Never press the blade directly on your clothes. Failure to do so may result in damage to the clothing.
8. This product is for general clothing lint only and should never be used for any other purpose. If used for other purposes, this can cause accidents or breakdowns.
9. Before using, check of the blade is damaged or distorted. Don’t use if there is any defect.
10. Do not store this product within children’s reach. It not a toy and using as may result in injury to the child.
11. Turn the machine off when you go out while charging. Failure to do so may result in a fire hazard, e.g. a short circuit fire

Battery

This product has a polymer lithium ion 2000mAh with protection.

1. The battery isfully charged in approximately 3 hours (a 5V/1A adapter is recommended) During the charging process the battery indicator will show three bars with some bars flashing. When the battery is fully charged, the bars will stop flashing This indicates that the battery is fully charged. The battery level changes in increments of 10%
2. Before charging, make sure that there are no foreign substances, such as dust or water droplets around the cables. Failure to do so may result in dangerous situations such as fire and electric shock
3. Charge your lint remover once a week during use. If you don t use the battery for a long period of time, the battery will deteriorate by natural discharge. If you don’t use it for a long time, . charge it at least once every 6 months.
4. When charging, do not leave the machine in hot places or in direct sunlight. When charging is complete, remove the charger immediately to prevent issues due to overcharging.

Product Usage Method

1. Open by turning the Grill

2. Detach Grill

3. Clean with the brush

4. Slide -of the refuse bin

5. Place lint into bin

Product Configuration Diagram

1. Battery Indicator
2. Display Charging
3. Gear Display
4. Speed Control Button
5. USB Charging Inlet
6. Grill
7. Blade
8. Suction Device
9. Refuse Bin
10. Main Body
11. Clean Brush
12. USB Cable

Warning

1. Do not carelessly remove the battery.

2. Be careful not to damage or shock the battery.

3. Keep the battery away from reach of children.

4. Never touch fluid inside the battery with your
   hands if it leaks. Wash with clean water immediately if it touches your eyes or skin, and consult your doctor immediately.

5. This product contains a lithium ion battery. Please dispose of the battery correctly through the adequate recycling entity closest to you.

6. When disposing of the device, make sure that the battery is removed from the device.

7. Be sure the power is off when removing the battery.

8. The battery must be safely disposed of.

Replacement Blades

When should the blade be changed?

1. With time and use the performance of the device may start to deteriorate This likely in dicates that the blade is less sharp

2.  The device comes with 3 sets of blades. One
   already mounted onto the device and two spares

3. If you need to buy additional blades you can do so here: http://www.gowiredluxcom/bladesUK
   UK
   Buy replacement blades here:

Or visit : go.wiredlux.comfblades

AUSTRALIA
Buy replacement blades here:
Or visit: go.wiredluxcom/bladesAUS

Any further questions and/or
concerns?

Please contact :support@wiredlux.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>