GIANNI WLP-100 Wireless Power Transfer Instruction Manual

June 3, 2024
GIANNI

GIANNI WLP-100 Wireless Power Transfer

GIANNI-WLP-100-Wireless-Power-Transfer-product

Dimension

Specifications

Transmitter on Frame Side

Input Power| 27.6 VDC
Current Draw| 1A/27.6VDC

*Requires 1.5 A power when energized

Lock Status Output| Relay (Dry contacts: N.O./N.C./Com.) Rating: 1A/ 30VDC


Door Status Output

| Reed Switch

(Dry contacts: N.O./N.C./Com.) Rating: 0.1A/ 20VDC

Receiver on Door Side
Output Power| 12/24 VDC


Current Draw

| 800mA/12VDC

400mA/24VDC

Lock Status Input| Dry contacts: N.O./Com.
Infrared Sensing| Transmitter        Receiver


Door Opening Time

| 15 / 30 seconds

*For fail-secure locks only

Maximum Door Gap| 3/16” (4~5mm)
Maximum Tolerance with 3/16″ (4~5mm) Door Gap| Horizontal alignment : 1/16″ (1mm) Vertical alignment : 1/16″ (1mm)

IR Sensing: 1/16” (1mm)

Operating Temperature| 32° to +120.2°F ( 0° to +49°C )
Humidity| 0 to 85% Non-condensing

GIANNI-WLP-100-Wireless-Power-Transfer-fig-2

Installation &Wiring

Included in Package

  • Door Side Unit
  • Wood Screws
  • Frame Side Unit
  • Metal Screws
  • Door Side Template
  • Mounting Tabs
  • Frame Side Template
  • Washers

Note: For optimal performance, it is recommended to minimize the door gap and use the supplied templates. The WLP-100 allows for some horizontal and vertical misalignment. Tolerance for minor misalignment will increase as the door gap decreases.

Installation Steps

  1. Door & Frame Inspection
    After checking the door and frame conditions, apply the templates at the appropriate location. The WLP-100 can be installed on the latch side, hinge side, or top of the door.
    1a. Apply the door-side template.
    1b. Apply the frame side template. Make sure to align the horizontal and vertical centerlines.

  2. Metal Door Installation
    2a. Center punch the screw locations for mounting tabs and counter-sink for the M5 screw. 2b. Cut out the main body on the door.GIANNI-WLP-100-Wireless-
Power-Transfer-fig-62c. Check if the WLP-100 fits well in the cutout and use the file if necessary. 2d. Install mounting tabs using M5 screws.

  3. Wood Door Installation
    3a. Drill two 1″ (25mm) diameter holes, 1/8″ (3mm) in depth as shown on the template. 3b. Drill and cut the WLP-100 main body to a minimum depth of 1-9/16” (40mm), and a diameter of 1″ (25mm) on the door side. 3c. Use the chisel to straighten the sides. 3d. Check if the WLP-100 fits well in the cutout and use the file if necessary. 3e. For the door side unit, drill a wiring channel to the electrified device to be powered.

  4. Selecting the Lock Output Voltage
    Use the jumper on the back of the door-side unit to select the appropriate lock voltage.

  5. Frame Installation

For the frame side unit, repeat steps 2 or 3 to install on a metal or wood frame.

Wiring Instructions

Please refer to the wiring diagrams on page 5, 6.

WLP-100 Pigtail Wire Color Function
The frame (Transmitter) Input Power Red (+) 27.6VDC / 1.5Amp
Black (-) Ground
Reed Switch Red N.C.
Black COM.
White N.O.

Relay Output (Lock Status)

| Yellow| N.C.
Green| COM.
Blue| N.O.
Receiver Unit

12VDC

24VDC

OUTPUT

| Door Leaf (Receiver)|

Lock Status Input

| Blue| N.O.
Green| COM.
Lock Power Output| Red (+)| 12 or 24VDC

(select through jumper setting)

Black (-)

WLP-100 Wiring Diagram (1)

GIANNI-WLP-100-Wireless-Power-Transfer-
fig-17

WLP-100 Wiring Diagram (2)

GIANNI-WLP-100-Wireless-Power-Transfer-
fig-18GIANNI-WLP-100-Wireless-Power-Transfer-
fig-19

  • Copyright © All Rights Reserved. P-MU-WLP-100 Published: 2022.05.13

Documents / Resources

| GIANNI WLP-100 Wireless Power Transfer [pdf] Instruction Manual
WLP-100 Wireless Power Transfer, WLP-100, Wireless Power Transfer, Power Transfer, Transfer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

GIANNI User Manuals

Related Manuals