LYNGDORF LS-1000 2-Way Line Source Speakers Installation Guide

: June 3, 2024
: LYNGDORF

Table of Contents

LS-1000 2-Way Line Source Speakers
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LS-1000 2-Way Line Source Speakers

LYNGDORF LS-1000 INSTALLATION MANUAL (working document)
LYNGDORF AUDIO LS-1000
LS-1000 Left, LS-1000 Right, LS-1000 Center
LS-1000
INSTALLATION LS-1000 Center MANUAL
[Skriv tekst]

TABLE OF CONTENTS
COMPLIANCE ………………………………………………………………………………………..3 PRE-INSTALLATION ……………………………………………………………………………….4 SPEAKER INSTALLATION ………………………………………………………………………7 LS-1000 LEFT/RIGHT MOUNTING DIMENSIONS ………………………………………9 LS-1000 CENTER MOUNTING DIMENSIONS ………………………………………….11 TECHNICAL SPECIFICATIONS………………………………………………………………13 SERVICE INFORMATION ………………………………………………………………………14

Lyngdorf Audio LS-1000 Installation manual

2

COMPLIANCE
WEEE The European Parliament and the Council of the European Union have issued the Waste Electrical and Electronic Equipment Directive. The purpose of the Directive is to prevent waste of electrical and electronic equipment and to promote reuse, recycling, and other forms of waste recovery. Steinway Lyngdorf products and the accessories packed with them are subject to the WEEE Directive. Please dispose of any waste materials in accordance with your local recycling regulations. Products and equipment which must be collected for reuse, recycling, and other forms of recovery are marked with the icon of the crossed-out waste receptacle.
FCC Steinway Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) this device must accept any interference received, including any interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed.

Lyngdorf Audio LS-1000 Installation manual

3

PRE-INSTALLATION
Unpacking the Model LS-1000 Left/Center/Right Carefully remove the loudspeaker units and accessories from the carton and check for shipping damage. Contact both the shipper and your local Lyngdorf Audio representative immediately if the unit bears any sign of damage from mishandling. In some cases, it may be necessary to return the equipment to Lyngdorf Audio or an authorized service provider for repair; therefore, it is recommended that you save your original packing materials. If this unit is shipped without the original packing, damage could occur and void the warranty.

LS-1000 Left

LS-1000 Center

LS-1000 Right

Lyngdorf Audio LS-1000 Installation manual

4

Inventory Check to ensure that all necessary product components have been delivered. Report all discrepancies to your local Lyngdorf Audio representative immediately.
· Lyngdorf LS-1000 Left, or Lyngdorf LS-1000 Center, or Lyngdorf LS-1000 Right · Side brackets for securing the individual speaker units to each other (attached to each side prior to
shipping) · Top and base brackets for securing the top and bottom speaker unit in each stack · Mounting screws for top, base and side brackets

Prepare the Wall for the Speaker Stacks For proper mounting of a Lyngdorf LS-1000 Left, Center or Right loudspeaker stack, a rectangular cutout with the following dimensions must be made in the wall:

Lyngdorf Audio LS-1000 Installation manual

5

Required space for Lyngdorf LS-1000 Left/Right The minimum space required including top and base brackets bracket are:

Speaker LS-1000 Left/Right each additional LS-1000 Left/Right 4 x LS-1000 Left/Right

Depth 95 mm / 3.7 in 95 mm / 3.7 in
95 mm / 3.7 in

Height 585 mm / 23 in 500 mm / 19.7 in
2085 mm / 85 in

Width 290 mm / 11.4 in 290 mm / 11.4 in
290 mm / 11.4 in

Required space for Lyngdorf LS-1000 Center The minimum space required including top and base brackets bracket are:

Speaker LS-1000 Center each additional LS-1000 Center 4 x LS-1000 Center

Depth 142 mm / 5.6 in 142 mm / 5.6 in
142 mm / 5.6 in

Height 585 mm / 23 in 500 mm / 19.7 in
2085 mm / 85 in

Width 290 mm / 11.4 in 290 mm / 11.4 in
290 mm / 11.4 in

Cables Recommended minimum up to 16m / 50ft: AWG 14/2 or 2-lead 2mm2 Recommended minimum from 16m / 50ft and up: AWG 12/2 or 2-lead 3.5mm2 Recommended maximum: Double AWG 10/2 or 2-lead 5mm2
Allow min. 50cm longer cable for connecting the cable to the speaker binding posts before the speaker is placed inside the wall or ceiling.

Arranging the speaker units Arrange the individual LS-1000 units on the floor, ready to combine them as a stack. For each loudspeaker stack, place the loudspeakers with the back side down on the floor, preferably close to the wall cutout in which the stack is to be mounted. Make sure that the floor is covered with fabric such as carpeting – to avoid scratching the loudspeakers.

Lyngdorf Audio LS-1000 Installation manual

6

SPEAKER INSTALLATION
Place the loudspeakers in order, with the bottom loudspeaker in the stack closest to the bottom edge of the wall cutout in which the stack is to be mounted. This facilitates easy mounting when connections are complete, as the stack can be tilted directly into place. Remove the Side Brackets from Each Speaker Unit All Lyngdorf LS-1000 loudspeaker units are equipped with POM thermoplastic side brackets from the factory. When these brackets are mounted correctly on the left, right, and rear sides of the units, they align and secure the individual units in a stack to each other. Using a Phillips (PH) type screwdriver, remove the screws securing the brackets to the loudspeakers, keeping the brackets and screws close at hand.
Mount the Side Brackets on Each Stack Using the screws you have just removed from the side brackets, secure the side brackets to the stack as shown. The bracket must bridge two loudspeakers in such a way that the bracket can be affixed to each loudspeaker with two screws. First, insert the screws into all four holes and tighten them by hand until the head of each screw protrudes 1-2 mm, then tighten the screws with a Phillips (PH) screwdriver. If you mount the bracket one screw at a time, there is a risk that the last screw will not be fully aligned with the hole. Tightening the last screw can then result in the screw thread being stripped, rendering the screw useless and resulting in an unstable loudspeaker stack.

Lyngdorf Audio LS-1000 Installation manual

7

Mount the Brackets for the Top and Bottom Loudspeakers Using a Phillips (PH) screwdriver and the supplied black M6x40 screws, secure the dedicated top and bottom brackets to the loudspeakers in their respective stacks as shown to the right.
Connect the Loudspeaker Cables Connect and tighten the speaker cables to the base plate of the first LS-1000 speaker. Make sure the cable ends are securely tightened and no bare wire is standing out. Other LS-1000 elements will connect through the plug-in terminals.

Lyngdorf Audio LS-1000 Installation manual

8

Mount the Wall Bracket Mount the top bracket to the top loudspeaker using a Phillips (PH) screwdriver and the supplied black M6x15 screws. Align the speaker stack with the wall opening and ensure the stack stands leveled and steady by adjusting the base feet.
Mount the top wall bracket to the top beam of the wall cutout, using a Phillips (PH) screwdriver and the supplied C6x40 screws. Note that the purpose of the top wall bracket is to stabilize the stack at the beam, and not to bear its weight. The loudspeaker stack and its base bracket must stand firmly on the ground. Cover the bracket as shown.
NOTE! For your own safety, do not attempt to raise the stack by yourself. There should be one person involved in lifting a loudspeaker stack for every two loudspeaker units in the stack; so a stack of 4 x LS1000 loudspeaker units requires at least two people to lift.

Lyngdorf Audio LS-1000 Installation manual

9

4 X LS-1000 LEFT/RIGHT MOUNTING DIMENSIONS

290 cm / 11.4″

2085 cm / 85″

Lyngdorf Audio LS-1000 Installation manual

10

4 X LS-1000 CENTER MOUNTING DIMENSIONS
290 cm / 11.4″
2085 cm / 85″

Lyngdorf Audio LS-1000 Installation manual

11

Example of finished LS speaker system with 4 x LS-1000 each for left, center, right channel

Lyngdorf Audio LS-1000 Installation manual

12

TECHNICAL SPECIFICATIONS

LS-1000 Left/Right Description: Power handling: Nominal Impedance: Tweeter: Midrange driver: Frequency response: Sensitivity: Crossover point: Connections: Mounting: Dimensions (WHD): Weight: Finish:
LS-1000 Center Description: Power handling: Nominal Impedance: Tweeter: Midrange driver: Frequency response: Sensitivity: Crossover point: Connections: Mounting: Dimensions (WHD): Weight: Finish:

2-way line source, closed 300 W 16 Ohm 8 pcs 1″ dome 4 pcs 115 mm, 25mm voice coil, aluminum cone, vented magnet 100 20.000 Hz (-3 dB) 98 dB 2.83 v/ 1 m 1,8 kHz Screw terminals In wall 280 x 500 x 85 mm / 11 x 19.7 x 3,35 inches + mounting 9,9 kg / 21.8 lb Matte black
2-way line source, closed 300 W 16 Ohm 8 pcs 1″ dome 4 pcs 115 mm, 25mm voice coil, aluminum cone, vented magnet 100 20.000 Hz (-3 dB) 98 dB 2.83 v/ 1 m 1,8 kHz Screw terminals In wall 280 x 500 x 132 mm / 11 x 19.7 x 5.2 inches + mounting 10,4 kg / 22.9 lb Matte black

Lyngdorf Audio LS-1000 Installation manual

13

SERVICE INFORMATION
To obtain warranty service, you must contact your original dealer or the Steinway Lyngdorf distributor of the region or country where you are located. If you have trouble locating an authorized representative, please find contact information at www.steinwaylyngdorf.com
Steinway Lyngdorf Ulvevej 28 DK 7800 Skive Denmark
In some cases, it may be necessary to return the equipment to Steinway Lyngdorf or an authorized service provider for repair; therefore, it is recommended that you save your original packing materials. Steinway Lyngdorf will not be responsible for any damage due to unauthorized packing or shipment in non-original packing materials. If return is made in authorized packaging, risks are borne by Steinway Lyngdorf. Additional charges may occur if new packing materials are required for return shipment.
Please check the latest version of this printed manual on our website:
www.steinwaylyngdorf.com

Lyngdorf Audio LS-1000 Installation manual

14

Lyngdorf Audio LS-1000 Installation manual

15

SL AUDIO A/S · ULVEVEJ 28 · 7800 SKIVE · DENMARK · WWW.STEINWAYLYNGDORF.COM