LYNGDORF D-500 Discreet Series Loudspeaker Instruction Manual

LYNGDORF D-500 Discreet Series Loudspeaker COMPLIANCE

WEEE
The European Parliament and the Council of the European Union have issued the Waste Electrical and Electronic Equipment Directive. The purpose of the Directive is to prevent waste of electrical and electronic equipment and to promote reuse, recycling, and other forms of waste recovery. Steinway Lyngdorf products and the accessories packed with them are subject to the WEEE Directive. Please dispose of any waste materials in accordance with your local recycling regulations. Products and equipment which must be collected for reuse, recycling, and other forms of recovery are marked with the icon of the crossed-out waste receptacle.

FCC
Steinway Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) this device must accept any interference received, including any interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed.

PRE-INSTALLATION

Unpacking the loudspeaker

Carefully remove the loudspeaker units and accessories from the carton and check for shipping damage. Contact both the shipper and your local Lyngdorf Audio representative immediately if the unit bears any sign of damage from mishandling. In some cases, it may be necessary to return the equipment to Lyngdorf Audio or an authorized service provider for repair; therefore, it is recommended that you save your original packing materials. If this unit is shipped without the original packing, damage could occur and void the warranty.

Inventory
Check the list below to ensure that all necessary product components have been delivered. Please report all discrepancies to your Steinway Lyngdorf representative immediately.

• Loudspeaker with mounting legs on the sides
• Installation manual
• Installation cut-out template
• Loudspeaker grill
• Lyngdorf logo badge
• Hex 3 bits
• Safety wire (only for D-5 IC)

Weight
Please ensure that the wall or ceiling type can handle the weight of the speaker in the chosen position, and that the mounting legs can hold tight.

• D-500 7,4 kg / 16 lb
• D-500 Center 11,5 kg / 25.4 lb
• D-5 6,4 kg / 14.1 lb
• D-5 IC 6,9 kg / 15.2 lb

Cables

Recommended minimum up to 16m / 50ft: AWG 14/2 or 2-lead 2mm2
Recommended minimum from 16m / 50ft and up: AWG 12/2 or 2-lead 3.5mm2
Recommended maximum: Double AWG 10/2 or 2-lead 5mm2
Allow min. 50cm longer cable for each speaker for connecting the cable to the speaker binding posts before the speaker is placed inside the wall or ceiling.

Safety Wire

When mounting the D-5 IC in the ceiling, the safety wire must be used to prevent damages and accidents.
Make sure the safety wire and safety hook are not making contact with the speaker cable connectors.

Cut-out Hole Dimensions

Be sure there is ample clearance behind the wall or ceiling to allow for the speaker to be properly installed.
With all speaker models you will find the relevant cut-out template. The minimum cut-out dimensions required are:

Speaker| Cut-out height| Cut-out width| Speaker depth incl. cabinet
---|---|---|---
D-500| 751 mm / 29.6 in| 226 mm / 8.9 in| 100 mm / 3.9 in
D-500 Center| 360 mm / 14.2 in| 618 mm / 24.3 in| 104 mm / 4.1 in
D-5| 334 mm / 13.2 in| 334 mm / 13.2 in| 104 mm / 4.1 in
D-5 IC| 334 mm / 13.2 in| 334 mm / 13.2 in| 109 mm / 4.3 in

The cut-out width and height must be with a maximum deviation of +/- 2mm or +/- 0.08 in.
The cut-out depth should allow a minimum of +2mm or +0.08 in extra space behind the speaker cabinet.

Placement of speakers

It is recommended to place the speakers so that they

• align acoustically with each other
• align with the screen and listener’s ear height
• meet the guidelines for either stereo or surround sound placement

Listening view example:

Ceiling view example:

Screen and listener alignment example:

SPEAKER INSTALLATION

1. Hold the loudspeakers near the cut-out and connect the loudspeaker wires. Make sure the cable ends are securely tightened and no bare wire is standing out.
2. Insert the loudspeaker into the cut-out and align the speaker.
3. Usinga Hex 3 key, turn each mounting screw clockwise until it is firmly in place. This will automatically turn the red mounting legs inside by 90 degrees, and each further turn with the Allen Key will pull the loudspeaker against the wall. If you are using an electric screwdriver, set it to the lowest torque to prevent overtightening or damaging the wall, and tighten with a Hex key by hand.
4. Attach the included grill to the loudspeaker and place the Lyngdorf Logo (optional).

D-500 MOUNTING DIMENSIONS

D-500 CENTER MOUNTING DIMENSIONS

D-5 MOUNTING DIMENSIONS

D-5 IC MOUNTING DIMENSIONS

TECHNICAL SPECIFICATIONS

D-500

• Description: 2 way speaker with 2 passive woofers
• Tweeter: 28 mm / 1,1” soft dome
• Midrange driver: 175 mm, 38 mm voice coil, aluminum cone, vented magnet
• Passive woofer: 2 x 175 mm, aluminum cones
• Enclosure: Closed compound cabinet
• Frequency range: 50 – 22.000 Hz (-3 dB)
• Nominal Impedance: 4 Ohm
• Sensitivity: 88 dB (2.83V/1m)
• Power handling: 100 W (IEC)
• Maximum SPL: 105 dB
• Crossover point: 2,5 kHz
• Connections: Binding posts
• Mounting: In-wall
• Dimensions w. grill (W x H x D): 254 x 779 x 106 mm / 10 x 30.7 x 4.2 inches
• Cut-out dimensions (W x H x D): 226 x 751 x 100 mm / 8.9 x 29.6 x 3.9 inches
• Weight: 7,4 kg / 16 lb
• Finish: Matte black, white grill

D-500 Center

• Description: 2 way speaker with 2 passive woofers
• Tweeter: 28 mm / 1” soft dome
• Midrange driver: 175 mm, 38 mm voice coil, aluminum cone, vented magnet
• Passive woofers: 2 x 175 mm, aluminum cones
• Enclosure: Closed MDF cabinet
• Frequency range: 50 – 22.000 Hz (-3 dB)
• Nominal Impedance: 4 Ohm
• Sensitivity: 88 dB (2.83V/1m)
• Power handling: 100 W (IEC)
• Maximum SPL: 105 dB
• Crossover point: 2,5 kHz
• Connections: Binding posts
• Mounting: In-wall
• Dimensions w. grill (W x H x D): 646 x 388 x 109 mm / 25.4 x 15.3 x 4.3 inches Cut-out dimensions (W x H x D): 618 x 360 x 104 mm / 24.3 x 14.2 x 4.1 inches
• Weight: 11,5 kg / 25.4 lb
• Finish: Matte black, white grill

D-5

• Description: 2 way speaker
• Tweeter: 25 mm / 1” soft dome Midrange driver: 180 mm, 35 mm voice coil, aluminum cone, vented magnet Enclosure: Closed MDF cabinet
• Frequency range: 80 – 20,000 Hz (-3 dB)
• Nominal Impedance: 4 Ohm
• Sensitivity: 89 dB (2.83V/1m)
• Power handling: 100 W (IEC)
• Maximum SPL: 106 dB
• Crossover point: 2,2 kHz
• Connections: Binding posts
• Mounting: In-wall
• Dimensions w. grill (W x H x D): 362 x 362 x 109 mm / 14.25 x 14.25 x 4.3 inches
• Cut-out dimensions (W x H x D): 334 x 334 x 104 mm / 13.2 x 13.2 x 4.1 inches
• Weight: 6,4 kg / 14.1 lb
• Finish: Matte black, white grill

D-5 IC

• Description: 2-way speaker
• Tweeter: 25 mm / 1” soft dome Midrange driver: 180 mm, 35 mm voice coil, aluminum cone, vented magnet Enclosure: Closed MDF cabinet
• Frequency range: 80 – 20,000 Hz (-3 dB)
• Nominal Impedance: 4 Ohm
• Sensitivity: 88 dB (2.83V/1m)
• Power handling: 100 W (IEC)
• Maximum SPL: 105 dB
• Crossover point: 2,2 kHz
• Connections: Binding posts
• Mounting : In-ceiling
• Dimensions w. grill (W x H x D): 362 x 362 x 114 mm / 14.25 x 14.25 x 4.5 inches
• Cut-out dimensions (W x H x D): 334 x 334 x 109 mm / 13.2 x 13.2 x 4.3 inches
• Weight: 6,9 kg / 15.2 lb
• Finish: Matte black, white grill

SERVICE INFORMATION

To obtain warranty service, you must contact your original dealer or the Steinway Lyngdorf distributor of the region or country where you are located. If you have trouble locating an authorized representative, please find contact information at www.steinwaylyngdorf.com, 

• Steinway Lyngdorf
• Ulvevej 28
• DK 7800 Skive
• Denmark

In some cases, it may be necessary to return the equipment to Steinway Lyngdorf or an authorized service provider for repair; therefore, it is recommended that you save your original packing materials. Steinway Lyngdorf will not be responsible for any damage due to unauthorized packing or shipment in non-original packing materials. If the return is made in authorized packaging, risks are borne by Steinway Lyngdorf. Additional charges may occur if new packing materials are required for the return shipment.
Please check the latest version of this printed manual on our website:
www.steinwaylyngdorf.com 

References

• Welcome to Steinway Lyngdorf - The world's finest audio systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>