VISUAL COMFORT ARN 2651 Keil Large Swing Arm Wall Light Installation Guide
- June 3, 2024
- VISUAL COMFORT
Table of Contents
Keil Large Swing Arm Wall Light
Item #ARN 2651
ASSEMBLY INSTRUCTIONS
Portable assembly
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
| Phillips Screwdriver | Slotted Screwdriver | Drill |
|---|---|---|
| Hammer | Pencil |
- Carefully remove all parts from the box. Place on a clean, soft surface.
- Remove portable mounting plate (N) from fixture body (D) by unscrewing side screws (C).
- Using the portable plate (N) as a guide, line up with the wall and mark anchor positions.
- Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (I) into the holes using hammer.
- Install portable mounting plate (N) to wall by securing wood screws (J) to anchors (I).
- Install fixture body (D) to portable mounting plate (N) and secure with side screws (C).
- Remove socket ring (G) from socket (E), then attach shade (F) to socket (E) and secure with socket ring (G).
- Insert light bulb into the socket.
- Swing the arm to desired angle.
- Remove the protective plug cover (L) from the plug (K).
- Plug into a proper electrical outlet and test the fixture.
Care Instructions : Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
Hardwire assembly
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
| Phillips Screwdriver | Slotted Screwdriver | Drill |
|---|---|---|
| Hammer | Pencil |
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove the portable mounting plate (N) from the fixture body (D) by unscrewing the side screws (C).
-
Using hardwire mounting plate (A) as a guide, line up with the junction box and mark anchor positions.
-
Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (I) into the holes.
-
Install hardwire mounting plate (A) to junction box and secure with mounting screws (B), then secure wood screws (J) to anchors (I) using hammer.
-
Remove the portable cord by unscrewing wire nuts (M).
-
Install direct wire plug (H) into the wire exit on the bottom of fixture body (D).
-
Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (I).
NOTE: It is imperative that the fixture is grounded. -
Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (I).
-
Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (I).
CAUTION: Do not reverse the hot and neutral connections.
Hardwire assembly
** NOTICE:**
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. -
Make sure all wire connections are tight, then carefully tuck into the junction box.
-
Install fixture body (D) to hardwire mounting plate (A) and secure with side screws (C).
-
Remove socket ring (G) from socket (E), then attach shade (F) to socket (E) and secure with socket ring (G).
-
Insert light bulb into the socket.
-
Swing the arm to desired angle. Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>