AcuityBrands LDN8 LED Cylinders LED Surface Pendant and Wall Mount Cylinders Instruction Manual
- June 9, 2024
- AcuityBrands
Table of Contents
Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
- To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
- Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
- Installation and service of luminaires should be performed by a qualified licensed electrician.
- Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
- It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
- DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
- if the lamp is marked (Hg) it contains Mercury. Follow all disposal laws. See www.lamprecycle.org.
- These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.
WARNING RISK OF ELECTRIC SHOCK
✓ Disconnect or turn off power before installation or servicing.
✓ Verify that supply voltage is correct by comparing it with the luminaire
label information.
✓ Make all electrical and grounded connections in accordance with the National
Electrical Code (NEC) and any applicable local code requirements.
✓ All wiring connections should be capped with UL approved recognized wire
connectors.
CAUTION RISK OF INJURY
✓ Wear gloves and safety glasses at all times when removing luminaire from
carton, installing, servicing or performing maintenance.
✓ Avoid direct eye exposure to the light source while it is on.
WARNING RISK OF BURN
✓ Allow lamp/fixture to cool before handling. Do not touch hot lens, lamp,
guard, or enclosure.
✓ Do not exceed maximum wattage marked on luminaire label.
✓ Follow all lamp manufacturer’s warnings, recommendations and restrictions on
lamp operation including but not limited to: ballast type, burning position,
replacement, and recycling.
✓ Use only lamps that comply with ANSI standards.
CAUTION RISK OF FIRE
✓ Keep combustible and other materials that can burn away from lamp/lens.
✓ Do not operate in close proximity to persons, combustible materials or
substances affected by heat or drying.
Please see product specific installation instructions for additional warnings
or any applicable FCC or other regulatory statements. Failure to follow any of
these instructions could void product warranties. For a complete listing of
product Terms and Conditions, please visit
www.acuitybrands.com.
Our Brands| Indoor/Outdoor| Indoor Lighting| Outdoor Lighting| Controls|
Daylighting
---|---|---|---|---|---
Lithonia Lighting| Gotham| American Electric Lighting| DARK TO LIGHT|
SunOptics
Carandini| Mark Architectural Lighting| Antique Street Lamps| LC& D|
Holophane| Peerless| Hydrel| ROAM|
RELOC| Renaissance Lighting| Tersen| Sensor Switch|
Light Concepts| Winona Lighting| | Synergy|
INSTALLATION INSTRUCTIONS
CYS/CRS stem swivel
Upon receipt, thoroughly inspect for any freight damage which should be
brought to the attention of the delivery carrier.
Compare the catalog description listed on the packing slip with the label on
the carton to ensure that you have received the correct merchandise.
IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
WARNING!!! RISK OF INJURY OR DEATH!!! Stem mounted fixtures should not be installed in any application where they are subject to wind load. Consult technical support for further assistance.
-
Electric current can cause painful shock or serious injury unless handled properly. For you safety, always remember the following:
• Turn off the supply power.
• Ground the fixture to avoid potential electrical shocks.
• Do not handle an energized fixture or energize any fixture with wet hands, when standing on a wet or damp surface, or in water. -
Specific safety information concerning lamps:
• Match wattage of fixture and lamp exactly.
• Do not remove or insert lamp when power is on.
• Do not scratch glass or subject lamp to undue pressure as either may cause lamp breakage.
• Protect operating lamp from sources of moisture.
• If lamp is marked it contains mercury. Follow disposal laws. See: www.lamprecycle.org.
GOTHAM ARCHITECTURAL DOWNLIGHTING
1400 Lester Road Conyers Georgia 30012
P 800 315 4982 F 770 860 3129
www.gothamlighting.com
CJ520669 Rev. C 2/2014 3 of 4 ©2008, 2011 Acuity Brands Lighting, Inc. All
Rights Reserved.
Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out
of improper or careless installation or handling of its products.
© 2010 Acuity Brands Lighting, Inc. All rights reserved. 12/01/10 ABL General
Warnings, Form No. 503.204
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>