TRIPP-LITE B110-SP-CAT-OD2 IP68-Rated Gigabit PoE Outdoor In-Line Surge Protector User Manual

TRIPP-LITE B110-SP-CAT-OD2 IP68-Rated Gigabit PoE Outdoor In-Line Surge

Protector

Package Includes

• B110-SP-CAT-OD2 Outdoor In-Line Surge Protector
• 18 AWG Grounding Wire – 1 ft.
• Cable Gland, 8.4 mm Diameter (x3)
• Surface Screw Anchors (x4)
• Surface Mounting Screws (x4)
• Unit Cover Screws (x4)
• Owner’s Manual

Product Features

• Protects valuable indoor and outdoor PoE equipment from power surges, lightning, ESD and cable discharge events in unforgiving environments
• Complies with 802.3af, 802.3at and 802.3bt IEEE Standards
• Supports PoE devices up to 90W and Ethernet speeds up to 1 Gbps
• Meets the following IEC Regulations:
  • IEC 61000-4-2 (ESD) +/- 15kV(Air), +/- 8kV(Contact)
  • IEC 61000-4-5 (Lightning) 10kA (8/20μs), 20kV (8/20μs)
• Supports both Mid- and End-Span PoE
• Passive by design – no external power required.

Optional Accessories

• N224-Series Cat6 Plenum-Rated Solid-Core Bulk Cable
• N046-000 Punch Down Installation Tool

Mounting Instructions

1. Locate the mounting holes on the bottom of the enclosure, as shown in Figure 1.

2. Securely mount the bottom portion of the enclosure to the desired outdoor location. Screw hole diameter supports mounting screws up to M3.5.

Metric Cable Gland Assembly

Installation

Protect indoor and outdoor edge network devices like PoE cameras or LAN access points from electrical damage by installing the B110-SP-CAT-OD2 between the source and edge network equipment.

Notes:

• Maximum cable distance between B110-SP-CAT-OD2 and source is 328 ft. (100 m).
• Maximum cable distance between B110-SP-CAT-OD2 and equipment is 328 ft. (100 m).
• For best protection performance, the total cable distance in the installation should not exceed 328 ft. (100 m).
• The B110-SP-CAT-OD2 must be grounded to function properly.

Protecting Edge-Of-Network Equipment
This installation protects your edge equipment from surge, lightning or ESD damage. To protect both the source and edge equipment, refer to section Protecting Edge-Of-Network Source and Equipment in this guide.
Note : Use standard size Cat5e, Cat6 or Cat6a cables that feature a wire gauge of 23/24 AWG. Slim category cables are not supported.

1. Remove both the cap A and end nut E from one of the cable glands (refer to section Cable Gland Assembly).

2. Slide the cap and remaining portion of the cable gland onto both the included grounding wire and bare-wire category cable coming from your source (ex: PoE switch) as shown:
   Note : Use standard Cat5e, Cat6 or Cat6a cables with a wire gauge of 23/24 AWG. Slim category cables are not supported.

3. Insert both the grounding wire and the bare-wire end of the category cable in the enclosure, making sure it is inserted on the “cable end” side.

4. Screw the metric cable gland to the enclosure using the end nut D previously removed in step 1. Then, tighten the cap securely onto the cable gland.

5. Using a punch down tool (such as Tripp Lite’s N046-000, sold separately), connect the bare wire to the color-coded board inside the enclosure.

6. Repeat Steps 1-3 for the equipment (ex: PoE camera) side of the enclosure without the addition of a grounding wire.
   Note : To achieve the best protection performance, the Cat5e/6/6a patch cable between the equipment end of the B110-SP-CAT-OD surge protector and the equipment to be protected must not exceed 300 ft. (100 m).

7. Once both bare wires are connected, secure the PCBA board to the enclosure using the included mounting screws. Then, attach the grounding wire to the available screw on the PCBA board.
   Note : Make sure you connect your source to the cable end and your PoE- compliant device to the equipment end.

8. Screw the front cover to the back portion of the enclosure using the included unit cover screws.

9. The connected PoE device is now protected.

Protecting Edge-Of-Network Source and Equipment
The previous installation only protects your edge equipment from surge, lightning or ESD damage. To protect both the source and edge equipment, install two B110-SP-CAT-OD2 units in your application. A B110-SP-POE can be installed instead of a second B110-SP-CAT-OD2 to protect the source if the second unit will be installed indoors.
Note : Use standard size Cat5e, Cat6 or Cat6a cables that feature a wire gauge of 23/24 AWG. Slim category cables are not supported. Maximum cable distance between two B110-SP-CAT-OD2 units is 328 ft. (100 m).

1. Install a second B110-SP-CAT-OD2 between the first B110-SP-CAT-OD2 unit and your source following steps 1-3 in Protecting Edge-Of-Network Equipment section.
2. In order to protect both the source and edge equipment, the two B110-SP-CAT-OD2 units need to be wired cable-end to cable-end as shown below.

Specifications

• Input / Output Connectors RJ45 Female
• ESD Protection 15kV (Air), 8kV (Contact)
• Lightning Protection 10kA (8/20µs) / 20kV (8/20µs)
• Surge Reaction Speed < 1ns
• Operating Temperature Range -40°F to 158°F (-40°C to 70°C)
• Storage Temperature Range -40°F to 194°F (-40°C to 90°C)
• Relative Humidity Range 0 to 95% RH, Non-Condensing
• IP Rating IP68 (Dust-Proof / Water-Resistant)
• Network Speed 10/100/1000 Mbps
• Max Supported PoE Wattage 90W
• IEEE Standards Supported 802.3af, 802.3at, 802.2bt
• Span Support Mid- & End-Span
• Material ABS
• Dimensions [H x W x D] 3.2 x 2.8 x 6.5 in. (81 x 71 x 165 mm)
• Weight 0.51 lb. (0.23 kg)

Warranty and Product Registration

2-Year Limited Warranty
Tripp Lite warrants its products to be free from defects in materials and workmanship for a period of two (2) years from the date of initial purchase. Tripp Lite’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from Tripp Lite or an authorized Tripp Lite service center. Products must be returned to Tripp Lite or an authorized Tripp Lite service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment, which has been damaged by accident, negligence or misapplication or has been altered or modified in any way.

EXCEPT AS PROVIDED HEREIN, Tripp Lite MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser. EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL Tripp Lite BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

Product Registration
Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product! No purchase necessary. Void where prohibited. Some restrictions apply. See website for details. Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and illustrations may differ slightly from actual products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>