APC KP1-C Slimline Vandal Resistant Keypad with EM card Reader User Manual

APC KP1-C Slimline Vandal Resistant Keypad with EM card Reader

Introduction

The APC-KP1-C Is an IP 65 rated keypad with a built in card reader access control system. The APC-KP1-C can store up to 2000 Users. It supports three access modes; card, card plus PIN and card or PIN. Other features that are built in such as Anti-vandal, alarm, exit button, safe mode, wiegand input/output, etc.

Technical Specifications

Not related to the card.

Master card| Add/delete user
As reader| Support Wiegand 26bits, PIN wiegand output is virtual number.
Connect external reader| Can connect any EM/HID/IC readers with wiegand 26 output
Connect high power alarm| External current of the alarm ≥3A

Installation Procedure

Installation and Fixation

1. Drill hole on the wall according to the back cover of the keypad.
2. Feed the cable through cable hole and connect to the related cable. For the un-used wires please cut to unequal lengths and insulate with electrical tape.
3. Fix back cover on the post using the supplied screws.
4. After wiring connections are completed fix the keypad front cover to the back cover.

Wiring

Connection Diagram

Common power supply

Special Power Supply

Administrator Operation

To Reset to Factory Default

To reset to factory default, power off, press “” &hold whilst powering on, release “” when you hear the two beeps and the LED turns orange. Now the keypad needs to authorize the master add and delete card. Swipe the Master ADD first then the Master DELETE second. Now the LED will turn RED indicating success. If no cards are swiped within 10 seconds it will skip the Master Card Authorization.

Note: Resetting to factory default only resets the Programming Code and Master Cards.

Enter into Programming Code

Press * Master code # 888888 is the default factory master code.
Note: Below 3 to 11 items all operation need in programming mode.

Change Master Code

Press 0 New code # New code #
Note: The master code can be any 6 digits, please store this number carefully.

To add users

1. To add card users automatically. Press 1 Read card1 Read card2 … #
   The range of ID number is any number between 1~2000.

2. To add card users manually
   Press 1 ID number 1# read card1 ID number 2# read card2 … #
   First # is to “confirm”and the second # is the end of the current settings. Press ***** will exit the current operation.

3. To add no-card users
   Press 1 ID number 1# PIN 1 ID number 2# PIN 2 … #
   The PIN of is 4-8 digits any number.(exception of 1234)

4. To add card users synthetically
   Press 1 read card1 ID number 1# read card2 ID number 2# PIN# … #

5. To add users by manager card
   Manager add card Swipe add user card continuously Manager add card
   That is exit add users settings

6. To add consecutive card users
   Press 5 ID number # 8 digits number 1 # Card number #.
   Mark: The quantity of cards cannot not exceed 2000.The ID number must be continuous vacant number.

To delete users

1. Auto Delete
   Press 2 Read card1 Read card2 … #

2. Manual Delete
   Press 2 ID number1# … #

3. Synthetical Delete
   Press 2 Read card1 ID number1# … #

4. Delete all users
   Press 2 0000 #

5. To delete User by Manager Delete Card
   Manager delete card Swipe deletes user card continuously Manager delete card That is exit delete users settings.

Door Open mode settings

1. Open by cards:
   Press 3 0 #

2. Open by cards+PIN
   Press 3 1 #

3. Open by cards or PIN(Factory default)
   Press 3 2 #

4. Door relay time settings
   Press 4 0~99 #
   Marks: The door relay time is between 0~99 seconds, the factory default setting is 5 seconds.

Door open detection settings

1. To disable door open detection. (Factory default)
   Press 6 0 #

2. To enable door open detection
   Press 6 1 #

3. When this function is used there are two scenarios: If the door is opened normally but not closed after 1 minute the inside buzzer will beep automatically to remind people to close the door and continue for 1 minute before switching off automatically.

4. If the door is forced open, the inside buzzer and alarm output will both operate.

Security Mode settings

1. Normal status:(Factory default )
   Press 7 0 #

2. Keypad Lockout
   Press 7 1 #
   If there are 10 invalid cards or 10 incorrect PIN numbers in a 10 minute period either the keypad will lockout for 10 minutes.

3. Alarm Output
   Press 7 2 #
   If there are 10 invalid cards or 10 incorrect PIN numbers in a 10 minute period either the outside buzzer and alarm output will both operate.

Alarm output time

Press 9 1~3 #
Factory default is 1 minute

User Settings

1. Cards users change the PIN
   * Read Card Old PIN # New PIN # Repeat New PIN #
   Can be 4-8digits.The PIN cannot be changed to “1234”

2. No card users the PIN
   * ID number # Old PIN # New PIN # Repeat New PIN #
   Can be 4-8digits.The PIN cannot be changed to “1234”

3. Open door by users card
   Read Card If it is valid. the door will open.

4. Open door by PIN
   Users PIN # If the PIN is correct, the door will open.

5. Open door by users card+PIN
   Read Card Users PIN #
   If the card and PIN is correct, the door will open.

6. To remove the alarm
   The inside buzzer and alarm output will both operate.
   Read valid card or press Master Code # to reset the Door Forced Open warning.

7. Close the door forced warning
   Close the door or Read valid card or Master Code # to reset the Door Forced warning.

Sound and Light indication

Specifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>