HGLRC Racewhoop 25 HD FPV Racing Drone Instruction Manual

HGLRC Racewhoop 25 HD FPV Racing Drone Instruction Manual

Product Specifications

Product parameters

Model| Racwhoop25 HD FPV Racing Drone
Frame Kit| Racewhoop25 Frame Kit
Flight Controller| Zeus35 AIO
ESC| 35A 4in1
VTX| CADDX Nebula Nano
Motor| 2004 Motor 4S KV3000 6S KV1800
Support receiver| SBUS .DSMX.i.BUS
Input Voltage| 3-6S Lipo

Package Included

• Racwhoop25 HD FPV Racing Drone *1
• Accessory Package*1

Interface Description

Check the flight control drive

1. Long Press BOOT buttons. connect USB. The system automatically install the driver.

2. Driver cannot be installed, please download Impulse RC Driver Fixer

3. Double-click on the run(Plug in the flight controller to automatically install the driver)

4. open beta flight configurator ，enter DFU mode

5. Click Select firmware version

6. Click Load firmware. Waiting for completion It will be prompted upon completion.

7. Open beta flight configurator 。Controller plugged into the computer. Beta flight Automatically assigned port click “Connect” Enter setup inter face Different computer COM）
   

Calibration Accelerometer

1. Put the aircraft horizontal and click “Reset Z axis”
   Click again

UART serial port use

• UART1 uses VTX image transmission
• UART2 uses receiver telemetry

Select aircraft model

1. Click Select model.

2. Click Click “I understand the risks” Push Master to check motor steering “Master” Steering can be changed at BLHeli Suite
   

Choose ESC Protocol

1. Choose the right ESC protocol, the optional universal protocol DSHOT600.
   

Voltage Parameters setting

1. Click Setting parameters
   

Setting up The Receiver

1. Receiver connection diagram.

2. Click .have found “UART2” Open (SBUS The receiver serial port.
   

3. Open ( i BUS/DSMX) receiver serial port.

4. Set the SBUS receiver.
   

5. Set the i BUS receiver.
   

6. Set the DSMX receiver.
   

Check Receiver Signal

1. Click Check the remote control output signal.
   

VTX serial port use. VTX uses OSD smart audio

1. VTX connection diagram.

2. VTX serial port opens. The protocol is selected according toits own VTX.

Select flight mode Start up mode

1. Click  set up the function of remote control switch across the channel (below are for reference only)

LED settings

1. Click Turn on LED support.
   

2. Click .Click set according to need.
   

Troubleshooting

Warning:

Please read the cautions as follows, otherwise stability of your flight controller cannot be ensured, your flight controller will even get damaged.

• Keep focus on the polarity. Check carefully before power supply.
• Cut off the power when you connect, plug and pull anything.
• The refresh rate of PID and Gyroscope is up to 8K/8K.

After sales question:

1. After receiving the goods, it is found that the product cannot be used normally. If the return to the factory is a quality problem, the repair service will be provided free of charge.
2. If the product is damaged due to improper operation, the repair service may be provided under the condition that the inspection can be repaired.
3. For domestic customers, please contact the after-sales service personnel.
   For overseas customers, please contact the official website for after-sales service.

Product daily problems

1.OSD garbled:

If you find garbled characters, please open Betaflight, click “OSD” .and click “Font Manager”clicks on “Upload Font” to update

1. When plugged in the battery, the aircraft does not pass the self-test

without “BBB” sound. There is only one sound. Please check if the ESC agreement is correct

1. The spin of the aircraft keeps spinning
2. Please check if the propeller is correct
3. Please check if the motor direction is correct.

Customer Support

www.hglrc.com

References

• Innovation ignites your life – HGLRC Company

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>