okayo WaveTEAMS Digital Wireless Full Duplex Communication System Owner’s Manual
- June 12, 2024
- Okayo
Table of Contents
Okayo WaveTEAMS Digital Wireless Full Duplex Communication System
Product Information
This device is designed and manufactured to meet the government’s
requirements for exposure to radio waves. It is specifically designed to
comply with the emission limits for exposure to radio frequency (RF) energy
set by the Federal Communications Commission (FCC) of the U.S. Government. The
Specific Absorption Rate (SAR) is a unit of measurement used to determine the
amount of RF energy absorbed by the body when using a wireless device. The SAR
limit set by the FCC for this device is 0.242W/kg.
Product Usage Instructions
To ensure compliance with the SAR limit and minimize exposure toRF energy,
please follow these guidelines when using the device:
- Keep the device at a distance from your body: Maintain a minimum separation distance between the device and your body to reduce exposure. Consult the product manual for specific recommended distances.
- Use hands-free options: Whenever possible, utilize hands-free accessories such as headphones or Bluetooth devices to keep the device away from your body.
- Limit call duration: Minimize the duration of calls made with the device. Shorter call durations reduce overall exposure to RF energy.
- Ensure good signal strength: In areas with weak signal reception, the device may increase its RF energy output to establish and maintain a connection. Use the device in locations where signal strength is strong to avoid unnecessary RF exposure.
- Follow manufacturer’s instructions: Adhere to all usage instructions provided by the manufacturer to ensure proper and safe use of the device.
By following these guidelines, you can use the device while minimizing your exposure to RF energy and complying with the SAR limit set by the FCC.
Digital Wireless Full-Duplex Communication System
- 3~6 full-duplex conversations per team
- Hands-free
Overview
WaveTEAMS is a duplex communication system that allows 1 Master and 2-5 Sub- Masters to perform full-duplex communication at a time. Two roles can be set in a team
Master (M)
This is used by Chairman/Team Leader.
Sub-Master (S)
This is used by Participants.
Application sample
A Chairman (Master) and two to five Participants (Sub-Masters) talk freely in
a team.
Interface
Create a (confidential) team
- step – Create a Master to send a pairing signal. Press both the function and power buttons simultaneously to create a Master. Press the + – button to choose a live channel and confirm with a press of the function button. Then, the “Encoded” screen shows up, and press the + – button to decide if a confidential (2) team is needed and press the function button to confirm. The LED indicator starts to flash quickly. This Master is ready and sending a pairing signal. Do not press any button on Master now.
- step – Power on Sub-Masters to receive the pairing signal. Press the power button of any unit to turn on. Its screen shows the same live channel as Masters. If a different live channel shows up, power it off and then on again. Sub-Masters are created now. Note Get Sub-Masters close to Master within 2 meters. Last step – Your (confidential) team is ready! When pairing of all Sub-Masters is finished, short press the function button on Master to leave and start your team. Note Your live channel is secured and unchangeable if in a confidential team ).
- Operation at a Glance
Operation
Mute Sub-Masters (Master Priority, MP)
Master can mute all Sub-Masters by pressing and holding its talk/mute button
for 3 seconds during the conversation. All mic indicators start to flash and
the MP symbol ( ) shows up on screens. Simply press the Master’s Talk/mute
button again to unmute all Sub-Masters. Note Only the Master with PTB mode can
mute Sub-Masters.
Change your live channel
All units in an open team (Encoded Off) can manually adjust their live channel
if needed. Press both the + and = buttons simultaneously for 5 seconds until
the symbol & disappears. Then, press the ‡ = button to select another channel
and confirm with a press of the function button.
Adjust headphone volume
Short press the + – button on any unit to adjust the volume during your
conversation. Note listening at high volume for long periods may damage your
hearing.
Power off
Press the power button for 5 seconds to turn it off. In addition, Sub-Masters
will be off automatically when receiving no Master’s signal for 20 minutes.
When Encoded On, shutting Master off will also turn Sub-Masters off.
Mute Sub-Masters (Master Priority, MP)
Master can mute all Sub-Masters by pressing and holding its talk/mute button
for 3 seconds during the conversation. All mic indicators start to flash and
the MP symbol ( ) shows up on screens. Simply press the Master’s Talk/mute
button again to unmute all Sub-Masters. Note Only the Master with PTB mode can
mute Sub-Masters.
Change your live channel
All units in an open team (Encoded Off) can manually adjust their live channel
if needed. Press both the + and = buttons simultaneously for 5 seconds until
the symbol & disappears. Then, press the ‡ = button to select another channel
and confirm with a press of the function button.
Setting menu
Press and hold the function button for 5 seconds to enter the setting menu. Then, press the + – button to scroll the menu or change each setting and confirm with a press of the function button. Remember to select “Save & Exit” after all setting changes are completed.
- Cannot talk in the team
- Make sure the correct headset is plugged in.
- Make sure Master Priority is not activated by Master.
- Make sure your talk button lights up. If it doesn’t, wait till one of Sub-Master releases its talk right?
- Cannot mute Sub-Masters
- Make sure Talk mode PTB is correctly set on Master.
Mic indicators
LED indicators
- Troubleshooting tips
- No audio is heard
- Make sure the headphone volume is set correctly.
- Make sure the headset is correctly plugged in.
- Make sure your channel is set correctly in the team.
- You are not authorized in this confidential team (2).
Manufacturer’s Declaration
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications
not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment. (Example – use only shielded
interface cables when connecting to computer or peripheral devices).
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. The exposure standard for wireless devices
employing a unit of measurement is known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC is 0.242W/kg. This device complies with Part
15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation.
Disclaimer
This manual was made for the purpose to provide detailed product information
about WaveTEAMS that Okayo Electronics Co., Ltd. (Okayo) builds and delivers
to the market at the time on its birth. Okayo promises its best effort was
made to give accurate, complete, and informative product information to the
contents disclosed above. However, users shall be aware of the fact that
improvements and up-to-date of products could be made from time to time. Okayo
reserves the right to amend, revise and change in part or in total of the
product information at the time it believes there is a must. The publication
of this manual and products are given as it is. Okayo is not accountable for
the change/error in contents and text contained in this manual and involved
products taking place in the future
OKAYO ELECTRONICS CO., LTD.
No. 2, Gongye 10′ Rd., Dali Dist., Taichung 41280, Taiwan
Tel:+886-4-2491-4666 Fax:+886-4-2491-4755
E-mail: okayo@okayo.com
www.okayo.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>