BOYO VTL17LTJ Concealed Mount License Plate Camera Instruction Manual
- June 4, 2024
- BOYO
Table of Contents
VTL17LTJ Concealed Mount License Plate Camera
Instruction Manual
VTL17LTJ
Concealed Mount License Plate Camera with LED Lights/Trajectory Parking Lines
Bill of Materials
Specifications
| SENSOR | PC1058 |
|---|---|
| Effective Pixel | 976×592 |
| Video output | 1.0 VP, 75 Ohm-p |
| Vertical Sync Frequency | NTSC 60HZ |
| Scanning System | 2: 1 Interlace |
| Sync System | Internal |
| AGE | Auto |
| BLC | Auto |
| Resolution | 700 TV Lines |
| S/N Ratio | More Than 48dB |
| Current Consumption | No More 150mA |
| Power Supply | DC12V ± 10% |
| Operating Temperature | -22° ~ 176° F |
| Storage Temperature | -40° ~ 176° F |
| Viewing Angle | 170° |
| Water-Proof | IP68 |
| Minimum Illumination | 0.5Lux/F1.2(0Lux with LED) |
Installation
Monitor trigger when the reverse backup light comes on it will trigger the monitor to switch to the backup camera.
- Find a suitable location to surface mount and install the camera. Make sure the camera’s view is unobstructed and be careful not to drill into any wires that might damage the vehicle. When all connections have been made and before mounting the camera, verify the camera is working and has a good view of the area. Then mount the camera down with the supplied two screws.
- Connect the RED wire to the +12 volt reverse wire
- Connect the BLACK wire to the Chassis ground (a metal, non-painted surface).
- Connect the GREEN wire to the + 12V volt reverse wire.
- Run video cable through the vehicle, up to video monitor. (Avoid placing video cable where it can get pinched or damaged).
- Attach the YELLOW video RCA to the reverse camera input of the radio or video monitor; connect the RED wire coming from the YELLOW video RCA to the reverse trigger wire on the radio or video monitor.
NOTE: The camera comes with trajectory lines and a mirror image view
active. If you want to remove the parking lines or change the image to a
reverse image, follow the steps below:
A) Disconnect power to the camera.
B) Cut the BLUE loop to remove the trajectory parking lines. isolate and tape
the wires.
C) Cut the WHITE loop to get the normal image, isolate and tape the wires.
D) Reconnect power to the camera. If the trajectory parking lines are needed
or the image needs to go back to reverse, just follow the steps above and
reconnect the wires.
For any technical support,
contact888-941-3060 or email
info@visiontechamerica.com
WWW.VISIONTECHAMERICA.COM
Bill of Material
Specifications
- Moving Trajectory Parking Lines ·concealed Mount License Plate Camera With LED Lights
- 600 TVL Horizontal resolution
- Excellent Auto White Balance
- Reverse/Non-Reverse image selectable
- Parking Li ne on/off Selectable
- To Control LED Lights· 170 degrees wide viewing angle
Installation Tips
- VTL 17LT J is designed to work best on vehicles that have a license plate located at the center and above the rear bumper. If your vehicle has a plate location that is offset to the left side, or right side, or your plate is located under the bumper then the VTL 17LT J may not provide optimum performance,
- VTL 17LT J bar-bracket is designed to be mounted behind the license plate so only the camera is visible
- VTL 17LTJ is designed to use the existing License Plate mounting equipment.
Caution: The rearview camera must be mounted at an angle (30- 40 degrees). It must not be mounted horizontally straight. Otherwise, the sensitivity and accuracy will be affected accordingly.
Dimensions (Inches) & wiring
Installation Diagram
For technical support, contact 888-941 -3060 or email info@visiontechamerica.com WWW.VISIONTECHAMERICA.COM
FEATURES
- Moving Trajectory Parking Lines
- CMOS Sensor with LED Lights
- 600 TVL Horizontal Resolution
- 720×480 Pixels
- Waterproof (IP67)
- Reverse/ Non-Reverse Image Selectable
- Parking Line on/off Selectable
- LED Lights
- Excellent Night Vision Picture Quality
Manufactured by Vision Tech America, Inc.
VTL17LTJ
Concealed Mount License Plate Camera With LED Lights 
UPCCODE
Vision Tech America, Inc.
1452 E. Valencia Drive
Fullerton, CA 92831
Product Registration
Name————————————-
Address————————————-
City————————————-
Phone————————————-
Model No.————————————-
Purchased Date————————————-
City /State of Store————————————-| Company————————————-
State————————————-
Zip————————————-
Email:————————————-
Serial No.————————————-
Store Name————————————-
---|---
1-YEAR LIMITED WARRANTY
This limited warranty is given to the end-user or the retail purchaser
(referred to this warranty as “Original Purchaser”) that it will be free from
defects in mate rial and workmanship for a period of one year from the date
of the purchase of the new product (excluding accessory items such as power
cords, cradle, memory card, adaptor, and cables). A copy of the original proof
of purchase and this warranty card with the RMA number given by Vision Tech
America, Inc. is required to receive warranty service. In the unlikely event
that the new product should fail due to a defect in material or workmanship,
Vision Tech America, Inc. will repair or replace it with a new or refurbished
product, where each party will be responsible for one-way shipping for the
lower 48 States customers only. For International and U.S custom ers residing
in Hawaii, Alaska, and Puerto Rico, the customer is responsible for freight
charges incurred both ways:
This limited warranty does not cover any physical damage to this product,
damage caused by improper installation; improper use; misuse; neglect; repair
of cracked, scratched, broken or modified cosmetics; or parts that have been
altered or removed; damages done by another device used with this product
resulting from use of non BOYO®- brand parts. This warranty is VOID if you
purchased this product as used, floor model sample, or refurbished; if the
product has been altered or modi fied in any way (including but not limited
to attempted repair without authoriza on from BOYO®- Vision Tech America,
Inc. and/or alteration/removal of the serial number). This limited warranty
does not cover the vehicle of any damages or liabilities in which this product
is installed or being installed. This product does not guarantee avoidance of
vehicle collisions or accidents.
If you are having trouble with the product, please contact our technical
support at 888-941-3~6 & or email:
info@visiontechamerica.com with your
questions or comments.
If your product is eligible to receive a warranty, request warranty service
online by visiting http://visiontechamerica.com/site/get-warranty/
This warranty is invalid if the factory-applied serial number has been altered
or removed from the Product.
IMPORTANT: TO SEND DEFECTIVE PRODUCTS FOR WARRANTY SERVICE, YOU MUST
RECEIVE RMA (RETURN MATERIAL AUTHORIZATION) AND INCLUDE ORIGINAL PROOF OF
PURCHASE AND THIS WARRANTY CARD WITH THE SHIPMENT.
VISION TECH AMERICA CUSTOMER SERVICE CENTER
888-941-3&6& or visit
www.visiontechamerica.com
For an accessory or part not available from your authorized dealer, call
For U.S. 888-941-3&6& I International 714-446-~543
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>