BOYO VTM7012FHD 7 Inch HD Monitor User Manual

: June 4, 2024
: BOYO

BOYO VTM7012FHD 7 Inch HD Monitor

BOYO-VTM7012FHD-7-Inch-HD-Monitor-main

Product Features

Feature	VTM7012FHD	VTM9003FHD
Size	7” HD LCD	9” HD LCD
Resolution	1024 x 600
Aspect Ratio	16:9 wide screen
Video Inputs	3 (Ch1, Ch2, Ch3)
Audio Inputs	2 (Ch1, Ch2)
Display Triggers	3 (Ch1, Ch2, Ch3)
Video Signal	1080P AHD/720P AHD/CVBS – Auto Switch
Video System	PAL / NTSC – Auto Switch
Speaker	Built-in
Mirror Image	Selectable for each channel
Parking Guidelines	Selectable for each channel
Trigger Delay	Configurable
Screen Flip	Horizontal / Vertical Flip
Auto Dimming		Yes
Remote Control	Included
Max. Current	< 500mA @ 12VDC
Operating Power	12 ~ 24 VDC

Before Installation

Please check contents.
Perform bench test. Ensure the product is working before installation by connecting the monitor and the camera to 12VDC.
Perform pre-install test, before mounting the monitor and the camera. In very rare instances, a running engine causes interference.
All issues should be resolved. So, when the monitor and the cameras are mounted, wires are run and the power is turned on, and a problem is encounter, it will be easy to troubleshoot the problem.

Wiring

BOYO-VTM7012FHD-7-Inch-HD-Monitor-2

1| Black| 14-PIN| power cable connector|
---|---|---|---|---
2| Black| 4-PIN male| AV CH1 Input| AHD 1080P, AHD 720P, or CVBS
3| Black| 4-PIN male| AV CH2 Input| AHD 1080P, AHD 720P, or CVBS
4| Black| 4-PIN male| V CH3 Input| AHD 1080P, AHD 720P, or CVBS
5| Black| Wire| GND|
6| Red| Wire| ACC| DC 12-24V positive pole
| Yellow| Wire| Battery| DC 12-24V positive pole
7| Brown| Wire| CH1 Trigger| DC 12-24V positive pole
8| Green| Wire| CH2 Trigger| DC 12-24V positive pole
9| Blue| Wire| CH3 Trigger| DC 12-24V positive pole

A trigger wire is normally connected to a backup light, the left turn signal, and the right turn signal. When a trigger wire becomes hot, it will display the video input channel associated with the trigger.

Buttons & Sensors

BOYO-VTM7012FHD-7-Inch-HD-Monitor-9

Remote Control

Power key: short press to turn on or off Ë VIDEO key: CH1, CH2, CH3 video channel switching, to move up in menu setting
Right key: increase volume, increase analog value in the menu setting
MENU key: menu
Left key: decrease volume, decrease analog value in the menu setting
MODE key: image mode switching, to move

Operations: Using the Buttons

Default Mode

BOYO-VTM7012FHD-7-Inch-HD-Monitor-10.

OSD Setting Mode

Press (menu) to enter the OSD setting mode.

Repeated pressing of “MENU” button will cycle through

Image Setting à General Setting à System Setting à Volume Setting

To change the values:

Press (MENU) button to get to the right settings
Press (down) or (up) button to select the rows
Press (decrease) or (increase) to “decrease” or “increase” value or to turn “on” or “off”
Press (MENU) button to save new settings

Image Setting

BOYO-VTM7012FHD-7-Inch-HD-Monitor-5

BRIGHTNESS, CONTRAST, SATURATION
Control display brightness and color
RESET
reset the system to factory default
VERSION
The system version number

General Setting

1) GUIDELINES

Turn on or off the parking assist guidelines. Normally used with the backup camera.

2) DELAY

Off or set between 1~10seconds. The delay setting determines the number of seconds the video channel will stay on after trigger line goes off. If the system is set off, then the monitor will return to the previous state immediately once the trigger is turned off. If

delay is set 2s, then the monitor will return to the previous state

2s later after finished reversing

System Setting

BOYO-VTM7012FHD-7-Inch-HD-Monitor-7

1) LANGUAGE

English is the default. Japanese, Korean, Russian, and Chinese are available.

2) AUTO DIM

VTM9003FHD feature. When turned on, the screen brightness dims under low ambient light.

UPSIDE DOWN

Vertical display flip on or off

4) MIRROR

Horizontal display flip on or off. Used when a normal camera is used as a backup camera. When a ‘normal’ camera is directed toward rear, an object on the front-right side of the camera will show on the right side of the display screen. Turn the mirror ‘ON’ to display the object on the left side of the screen, like mirror.

5) VCOMDC

When too much backlight come through the LCD, the black screen with no image will look grey, not black. Decrease the value. It controls amount backlight passes through LCD.

VOLUME Setting

1) VOLUME

Adjust speaker volume

Warranty Information

This one-year limited warranty is given to the end-user or the retail purchaser (referred to this warranty as “Original Purchaser”) that it will be free from defects in material and workmanship for a period of one year from the date of the purchase of the new product (excluding accessory items such as power cords, cradle, memory card, adaptor, and cables).

This limited warranty does not cover any physical damage to, or misuse of, this product, damage caused by improper installation; improper use; misuse; neglect; repair of cracked, scratched, broken or modified cosmetics; or parts that have been altered or removed; damages done by

another device used with this product resulting from use of non-BOYO®- brand parts. This warranty is VOID if you purchased this product as used, floor model sample, or

refurbished; if the product has been altered or modified in any way (including but not limited to attempted repair without authorization from BOYO®- Vision Tech America, Inc. and/or alteration/removal of the serial number).

For warranty information, visit: https://www.visiontechamerica.com/get- warranty