VEGUe VW-022 Wireless Microphone Instruction Manual

VEGUe VW-022 Wireless Microphone

TECHNICAL PARAMETERS

Comprehensive characteristics

Receiver

Handheld Transmitter

RECEIVER FRONT PANEL FEATURES AND INSTRUCTION

➀ POWER Button: Press the power switch for 3 seconds, open power supply, LCD is bright; press the power switch for 3 seconds, the receiver power shut down.
➁ LCD Display: Display system in the current working state.
➂ Microphone A VOLUME control: Adjust the output volume. Clockwise rotation, the volume increase, Counterclockwise, the volume decrease.
➃ Microphone B VOLUME control: Adjust the output volume. Clockwise rotation, the volume increase, Counterclockwise, the volume decrease.

RECEIVER BACK PANEL FEATURES AND INSTRUCTION

➀ Antenna B connector
➁ Balanced Output B
➂ Mixing 6.35mm Output
➃ DC Power Input
➄ Balanced Output A
➅ Antenna A connector

TRANSMITTER FUNCTION AND DESCRIPTION

➀ Microphone head Section:
Including Microphone Cover Net and Microphone Cartridge’s Module.
➁ Display Screen:
Display working channels, battery power, frequency.
➂ Switch button:
Press for 3 seconds on/off the microphone.
➃ Frequency adjust button.

SYSTEM SETTINGS

1. Adjust the volume to the smallest before turned on the transmitter, then turn on the receiver, the LCD lights up and alphanumeric displayed, then LCD will display the channel and frequency of the receiver.
2. After the transmitter is installed with the battery, press the switch for 3 seconds, the transmitter enters normal operation.
3. Turn on the transmitter first. The screen of receiver will light on . Then adjust the volume. When speak, the AF on the screen will light. When no sound or AF doesn’t light, ii means there is something wrong with the system and it needs repair.
4. Press the POWER button for 2 or 3 seconds to turn off the receiver.
5. The transmitter adjustable button (ie, transmitter function and description point 4) directly adjusts different frequencies, press to change the frequency, the receiver can automatically match the corresponding frequency, A microphone and B microphone do not interfere with each other, all can work normally. If use multiple sets of microphones at the same time, it need to set all the microphone (press the adjustable buttons) to different frequencies.

RECEIVER SETTINGS

The display shows under normal working conditions. As shown below:

Receiver LCD display:
➀ RF signal strength display(RF)
➁ AF signal strength display(AF)
➂ CHANNEL: display the current working channel
➃ FREQUENCY: display the current working frequency

TRANSMITTER SETTINGS

Handheld transmitter display:
➀ BATTERY: Display the Remaining Electricity of
Transmitter Battery. When the battery power is low, the sign flashes. The battery should be replaced immediately to ensure the normal operation of the transmitter.
➁ FREQUENCY: Display current working frequency
➂ CHANNEL: Display current working channel

CONNECTION DIAGRAM

Choose one of the following four connection methods:

Note: The item doesn’t work with TV directly, therefore we suggest not to connect it with TV.

ACCESSORIES

TROUBLE SHOOTING

of the AC adapter is plugged into a power outlet and the other end is plugged into the DC input jack on the rear panel of the receiver;
Confirm that the AC power outlet is normal, and confirm that the power supply voltage is normal.
Transmitter power indicator is off| Turn on the transmitter power;
Verify that the +/- mark on the battery matches the transmitter’s termination;
nsert a new battery.
Receiver display RF level show| Increase the receiver volume control;
Check the cable connection between the receiver and the amplifier or mixer.
Receiver display RF level no display, transmitter power light is on| Vertically elongating the receiver antenna;
Remove the receiver from the side of the metal object;
Check for obstacles between the transmitter and receiver;
Moving the transmitter closer to the receiver;
Check that the receiver and transmitter are using the same frequency.
Transmitter power indicator flashes| Replace the transmitter battery
Distortion or unwanted burst noise| Receiver display RF level show| Remove nearby sources of RF interference (such as CD players, computers, digital devices, earphone monitoring systems, etc.);
Change the receiver and transmitter to different frequencies;
Replace the transmitter battery; Increase the frequency separation between systems if multiple systems are used.
The distortion level is gradually increasing| Transmitter power indicator flashes| Replace the transmitter battery

www.veguetech.com
veguetech@gmail.com
If you have any questions, please feel free to contact us.

Documents / Resources

| VEGUe VW-022 Wireless Microphone [pdf] Instruction Manual
VW-022, Wireless Microphone, VW-022 Wireless Microphone
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>