Intermec PM Series DUART Interface Board Installation Guide
- June 3, 2024
- Intermec
Table of Contents
Intermec PM Series DUART Interface Board
Intermec Technologies Corporation Worldwide Headquarters6001 36th Ave.W.
Everett, WA 98203U.S.A. www.intermec.com The
information contained herein is provided solely for the purpose of allowing
customers to operate and service Intermec-manufactured equipment and is not to
be released, reproduced, or used for any other purpose without written
permission of Intermec Technologies Corporation. Information and
specifications contained in this document are subject to change without prior
notice and do not represent a commitment on the part of Intermec Technologies
Corporation.© 2012–2013 by Intermec Technologies Corporation.
All rights reserved.The word Intermec, the Intermec logo, Norand, ArciTech,
Beverage Routebook, CrossBar, dcBrowser, Duratherm, EasyADC, EasyCoder,
EasySet, Fingerprint, INCA (under license), i-gistics, Intellitag, Intellitag
Gen2, JANUS, LabelShop, MobileLAN, Picolink, Ready-to-Work, RoutePower, Sabre,
ScanPlus, ShopScan, Smart Mobile Computing, SmartSystems, TE 2000, Trakker
Antares, and Vista Powered are either trademarks or registered trademarks of
Intermec Technologies Corporation. There are U.S. and foreign patents as well
as U.S. and foreign patents pending.
Install the DUART Interface Option Board
Use these instructions to install the DUART interface option board in Intermec PM23c, PM43, and PM43c printers. You will find these items in the shipping box:``
You will need the following tools to install the DUART interface option board:
- T20 Torx screwdrivers
- Small wrench
To install the DUART interface option board, you need to open the printer and physically install the board in the printer.
This board must only be installed by an authorized service technician
WARNING
- Follow standard ESD guidelines to avoid damaging the equipment you are servicing.
- Before you begin, turn off the printer and disconnect the power cord and communication cables.
- The electronic compartment contains wires and components with dangerous voltage. Make sure that the printer is switched off and the power cord is disconnected before the cover is removed.
Open the Printer
You need to remove both the media cover and the electronics cover to install the DUART interface option board.
To remove the media cover
- Open the media cover
- Use the small wrench to loosen the nut that secures the media cover latches in place.
- Slide the latches counterclockwise into the open position.
- Close the media cover and lift it off the hinges.
- Put the media cover aside on a soft cloth to avoid scratches.
To remove the electronics cover
- Use a T20 Torx screwdriver to remove the two screws that secure the electronics cover to the inside of the printer base.
- Use a T20 Torx screwdriver to remove the two screws located on the outside of the electronics cover.
- Remove the electronics cover, and put the cover aside on a soft cloth to avoid scratches.
To install the DUART interface option board
-
On the back of the printer, remove the two screws that secure the cover plate to the printer, and remove the cover plate
-
Attach the spacer screw to the center of the printer main board.
-
Insert the DUART interface option board into the printer and use the T20 Torx screwdriver to secure the board assembly to the printer with the two Torx screws removed in Step 1.
-
Use the T20 Torx screwdriver to secure the board assembly to the spacer screw with a Torx screw.
-
Insert the single or dual option board cable into the 80-pin connector on the printer main board.
-
Insert the other end of the option cable into the 80-pin connector on the DUART interface option board.
Note: You may need to use the dual option cable to connect to the main board depending on which slot you use for the DUART interface option board -
Install the jumpers and ICs on the board to configure each UART for the type of serial communication you want to use:
-
Replace the electronics cover.
-
Replace the media cover.
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
© 2013 Intermec Technologies Corporation. All rights reserved.
PM23c, PM43, PM43c DUART interface Option Board Installation Instructions
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>