hp OneShred 18CC Shredder User Manual
- June 3, 2024
- HP
Table of Contents
- Read the Operating Manual
- Intended Use
- Observe the Safety Information
- Checking the Package Contents
- General View of the Shredder
- Positioning the Shredder and Starting It Up
- Operating the Shredder
- Troubleshooting
- Technical Data
- Disposal
- Information on Storage
- Queries and Service
- Declaration of Conformity
- Manufacturer
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OneShred 18CC
OneShred 12MC
Shredder
Art. No.: 2805 / 2806
v1.11
www.hp.com/officeequipment
Read the Operating Manual
Read this operating manual through carefully, observing all the information contained regarding handling and using the shredder. Keep the operating manual close by for future reference.
Intended Use
The shredder has been designed to shred paper, credit cards, paper clips and staples. The shredder is exclusively intended for private use indoors. Any other use is considered unintended use. Unauthorised modifications or reconstructions are not permitted and lead to loss of rights to claims under the terms of guarantee.
Observe the Safety Information
Read and observe all the warnings to protect yourself and the environment from any harm.
Warning!
Risk of injury through the insertion mechanism. Loose items could get caught
in the insertion slot and cause injuries. Keep fingers, hair, scarves, ties,
jewellery etc. away from the insertion slot.
Warning!
Risk of injury through electric shock. Handling the shredder improperly could
lead to an electric shock. Unauthorised modifications or reconstructions to
the shredder are not permitted. Do not operate the shredder if the power cable
is damaged. Switch off the shredder immediately in the case of damage or
improper functioning and disconnect the power plug. Only use the power cable
supplied. Repairs may only be carried out by properly qualified specialists.
Pay attention that the shredder is set-up in the vicinity of an easily
accessible power socket so that the shredder can be disconnected from the
power supply in an emergency. Never handle the shredder with wet hands. Avoid
any contact with water. Always unplug the power plug when the device is not
being used. Only use the power cable supplied
Warning!
Risk of suffocation due to small parts, packaging or protective foils.
Children can swallow or choke on small parts, packaging and protective foils.
Keep the device and its packaging materials out of reach of children.
Warning!
This device can be used by children from the age of eight and persons with
restricted physical, sensory or mental capabilities or a lack of experience
and/or knowledge when they are supervised or have been instructed with regard
to safe use of the device and the risks involved with its use. Children must
not be allowed to play with the device. Children must not be allowed to
complete any cleaning or service work on the device without adequate
supervision.
Caution!
Risk of tripping due to improperly laid power cable. Lay the power cable in
such a way that nobody can trip over it. Make sure the power plug and cable
cannot be damaged.
Important!
Risk of property damage. Avoid exposing the device to environmental influences
such as smoke, dust, vibration, chemicals, moisture, heat or direct sunlight.
Only use the shredder in indoor rooms and within the permissible ambient
conditions stipulated in the Technical Data.
Observe the following information to ensure that the shredder always functions
as you expect it to.
| Read the operating manual thoroughly before
starting to use the device.| | Never reach into the insertion slot.
---|---|---|---
Keep long hair away from the shredder.| Keep children and pets away from the
shredder.
Keep all loose pieces of clothing, jewellery or other
loose items away from the shredder.| Do not spray any inflammable gases in the
direction of the shredder. Never use air sprays.
Keep ties and scarves away from the
shredder.| Observe the maximum number of sheets (refer to “Technical Data”).
General indication of potential risks,
so that particular care is required.| Caution! Risk of injury through
sharp edge of cutting mechanism!
Warning!
This device is not intended to be used by children. Prevent hands, clothes and
hair coming into contact with the insertion slot. Unplug the power plug if the
device will not be used for a longer period. This device is equipped with
hazardous moving parts, so ensure you keep limbs well away from the moving
parts.
Only use the product indoors.
The «Geprüfte Sicherheit» mark (GS tested safety mark) certifies that the
product satisfies the requirements defined by the German Product Safety Act
(ProdSG).
The GS tested safety mark indicates that when implemented for its intended use
and in the event of foreseeable misuse the identified product will not
endanger the safety and health of the user. It concerns a voluntary safety
mark which was issued by an authorized testing institute.
Credit cards must be inserted vertically.
The symbol indicates that the design of the product complies with Protection
Class II (double insulation). A safety connection to the electrical earthing
(ground) is not necessary.
Checking the Package Contents
Check the package contents of your shredder before putting the shredder into
operation.
If anything is missing or damaged, do not use the shredder. Contact our
Service department.
- 1 OneShred 18CC or OneShred
- 12MC shredder with waste bin for cuttings
- 1 operating manual
- 1 power cable
- 1 oiled sheet
General View of the Shredder
The following figure illustrates the shredder in detail.
1 | Operating buttons / Status indicator | 5 | Grip |
---|---|---|---|
2 | Insertion slot | 6 | Viewing window / Grip |
3 | Cutting mechanism | 7 | Waste bin |
4 | Status indicator, front | 8 | Castors |
1 | Reverse running button | 5 | Forward running button |
---|---|---|---|
2 | Overheat, status LED | 6 | Bin full, status LED |
3 | On/Off button | 7 | Bin open, status LED |
4 | Overload, status LED |
Positioning the Shredder and Starting It Up
The shredder only operates when the waste bin supplied is fitted. Do not position the shredder near any sources of heat and maintain a distance of at least 10 cm to walls. This ensures the shredder is sufficiently cooled.
-
Set the shredder down on a stable, level, horizontal surface and in the vicinity of an easily accessible power socket.
-
Slide the waste bin in the device. The waste bin latches audibly in place. If the waste bin is not fitted in the device properly, the shredder cannot be switched on.
Only use the power cable supplied. -
Connect the power cable to the device.
-
Connect the power plug to a power socket.
-
Switch the device on by pressing the On/Off button.
The status indicator lights up blue.
You have put the shredder into operation.
Operating the Shredder
The shredder works using an automatic shredding mechanism. The shredder is operated using the operating buttons on the top of the device.
The shredder is equipped with an additional status indicator at the front. This status indicator indicates a fault has occurred which is specified by the buttons and status LEDs on the top of the device.
Shredding Material Automatically
Observe the maximum permissible cutting capacity and other specifications
defined in Section Technical Data.
Warning! This device is not intended to be used by children. Prevent hands, clothes and hair coming into contact with the insertion slot. Unplug the power plug if the device will not be used for a longer period. This device is equipped with hazardous moving parts, so ensure you keep limbs well away from the moving parts.
Important!
Risk of property damage through material jam! Observe the maximum cutting
capacity of the insertion slot.
- Feed the material to be shredded in the centre of the insertion slot.
The insertion slot draws the material in automatically and stops when no more material is fed in.
Shredding Material Manually
On rare occasions, it is possible that the sensors do not detect the material
inserted.
-
Press and hold the FWD button.
The material is then drawn in and shredded. -
Release the FWD button.
Switching the Shredder Off
Switch the shredder off when you no longer need to use it.
-
Switch the device off by pressing the On/Off button.
The shredder is switched off. -
Disconnect the power plug from the power socket if the shredder will not be used for a longer period of time.
Sleep Mode
If the shredder remains switched on but is not operated for 30 minutes, it
automatically enters Sleep mode. The status indicator on the front of the
shredder goes out. The status indicator on the top of the shredder dims.
Proceed as follows to deactivate Sleep mode:
- Feed material to be shredded in the centre of the insertion slot.
The shredder is ready to operate again.
Alternatively, press the FWD or REV key on the shredder to deactivate Sleep mode.
Troubleshooting
The following information should provide help if something is not working as would be expected.
Overheating Protection
The shredder switches off automatically in the event of overheating. The
status indicator lights up RED.
Wait the period of time defined in Section Technical Data for the shredder to cool down.
When the cool down phase has elapsed, the status indicator lights up BLUE.
Shredding is resumed.
Observe the minimum clearance to walls and the information on continuous operation in Section Technical Data.
Overload Protection
If you have inserted more material than is specified in Section Technical Data
, the status indicator flashes RED and the shredder automatically starts
running in reverse for 5 seconds.
- Pull the material out of the shredder.
The blockage has now been cleared.
After the material has been removed from the shredder, the cutting mechanism continues to run for 3 seconds to clean itself. Wait until the shredder has stopped and the status indicator lights up BLUE.
Oiling the Cutting Mechanism
If you want to increase the working life of the shredder, you should oil
the shredder’s cutting mechanism at regular intervals.
Special oil and oiled sheets are available for the shredder from HP.
Important!
Risk of property damage through using the wrong oil! Do not use spray oils.
Only use a special oil intended for shredders.
There are various ways to oil the cutting mechanism.
Oiling Using Self-Oiled Paper:
- Apply the special oil for shredders in several lines horizontally across a sheet of paper.
- Insert the oiled sheet of paper in the insertion slot.
The paper with oil applied is inserted and oils the cutting mechanism.
Oiling Using Oiled Sheets
- Insert the oiled sheet in the paper infeed.
The paper with oil applied is inserted and oils the cutting mechanism.
Emptying the Waste Bin
The fill level of the waste bin is monitored by a sensor.
When the fill level is high, the “Bin full” status LED flashes RED. The
cutting mechanism of the shredder stops and you must empty the waste bin.
-
Switch the device off by pressing the On/Off button.
-
Pull the waste bin out of the device.
If you have not switched the device off, the “Bin open” status LED lights up RED. -
Empty the waste bin.
-
Slide the waste bin in the device.
The waste bin latches audibly in place.
You have emptied the waste bin.
Clearing Residual Material
If the shredder no longer shreds material as you expect, remove any residual
material from the cutting mechanism.
-
Press and hold the REV button. The cutting mechanism runs in reverse and releases any ma-terial remaining in the cutting mechanism.
-
Release the REV button.
-
Switch the device off by pressing the On/Off button.
-
Disconnect the power plug from the power socket.
Caution! Risk of injury through sharp edge of cutting mechanism! Take the utmost care when removing the material residue. -
Remove the residual material carefully from the cutting mechanism using an appropriate pointed object.
You have removed material residue from the cutting mechanism.
Cleaning the Shredder
Clean the shredder at regular intervals.
Caution! Risk of injury through flash flame! Such flash flames can occur
when using air sprays. Never use air sprays.
- Switch the device off by pressing the On/Off button.
- Disconnect the power plug from the power socket.
- Clean the surface of the housing with a soft, dry, lint-free cloth. Do not use any aerosols, solvents or cleaning agents.
Technical Data
Model | OneShred 18CC | OneShred 12MC |
---|---|---|
Dimensions (mm) | W:272 |
L: 400
H: 590| W:272
L: 400
H: 590
Security level compliant with DIN 66399-2| P-4| P-5
Cuttings size (thickness x width, mm)| 4 x35| 2 x 1 5
Max. cutting capacity (sheets / credit cards)| 18/1| 12/1
Working width (mm)| 220| 220
Power supply| 220-240 V-, 50/60 Hz,
2.0 A, 450 W| 220-240 V-, 50/60 Hz,
2.0 A, 650 W
Max. ambient temperature [°C]| 25| 25
Capacity, waste bin (l)| 25| 25
Weight (kg)| 12.| 12.
Volume (dB)| 65| 65
Continuous operation (min) / Cool down phase (min)| 20 / 20| 20 / 20
Operating speed (m/min)| 2.| 2.
Shred type| Cross cut| Micro -cut
We declare that these devices, with regard to their task of the destruction of
documents, fulfil the conditions defined for Security Levels P-4 and P-5 in
accordance with DIN 66399.
P-4: Recommended for data media containing particularly sensitive and
confidential data.
Material particle area ≤ 160 mm² and for consistent particles: strip width ≤ 6
mm (e.g. particles 4 x 40 mm).
P-5: Recommended for data media containing data which should remain secret.
Material particle area ≤ 30 mm² and for consistent particles: strip width ≤ 2
mm (e.g. particles 2 x 15 mm).
Disposal
The adjacent symbol indicates laws dictate that electrical and electronic
apparatus no longer required must be disposed of separate from domestic waste.
Dispose of your device at a collection point provided by your local public
waste authority. Packaging materials must be disposed of according to local
regulations.
Observe the identification on the packaging materials during the waste sorting
process; they are identified by abbreviations (b) and numbers (a) which have
the following significance: 1–7: plastic/20–22: paper and cardboard/80–98:
composite materials.
Packaging materials must be disposed of according to local regulations.
The packaging is made of environmentally friendly materials that you can
dispose of at local recycling points. Advice on the options with which to
dispose of your old device can be obtained from your municipal or local
administration offices.
The device and packaging materials can be recycled; sort them for disposal to
simplify waste management. The Triman logo is only relevant for France.r
Frankreich.
The device and the packaging material can be recycled, so sort them prior to
disposal for better waste management. Contact your local authorities for
information on the various options available to ensure correct disposal.
Observe the following identifications of the packaging materials: (a) numbers,
(b) abbreviations and (c) materials which have the following significance:
1–7: plastics / 20–22: paper and cardboard / 80–98: composite materials and
(d) type of packaging. The logo is only applicable to Italy.
Information on Storage
The shredder must be stored safely after use. Observe the following
information:
Store the shredder
■ in its original packaging
■ in a dry, clean location
■ in a cooled state
Queries and Service
Dear Customer,
We are delighted that you have chosen this product.
If it does not work as intended or it appears to be defective, please contact
the sales outlet where you purchased the product.
Further information is available under the heading Contact & Service on our
website: www.hp.com/officeequipment.
Declaration of Conformity
The CE mark on the device confirms its conformity.
The Declaration of Conformity can be read online at
www.hp.com/officeequipment.
The UKCA mark on the device confirms its conformity.
The Declaration of Conformity can be read online at
www.hp.com/officeequipment.
Manufacturer
GO Europe GmbH Zum Kraftwerk 1 D-45527 Hattingen Germany
All your office needs under one brand
HP is a trademark of HP Inc. or its affiliates, used by GO Europe GmbH under
license from HP Inc.
GO Europe GmbH Zum Kraftwerk 1, 45527 Hattingen (Germany)
www.hp.com/officeequipment
UK Authorised Representative (for authorities only)
ProductIP (UK) Ltd.
8, Northumberland Av.
London WC2N 5BY
The company reserves the right to change the content of this manual, and subsequent changes to the product without prior notice. We are not responsible for any direct, indirect, intentional or unintentional damage and hidden dangers caused by installation, misuse or use beyond the specifications provided by the manufacturer. Before placing your order, please check with the dealer to see if the product performance meets your needs. HP is a registered trademark of HP Inc. The ownership of other trademarks involved in this manual is owned by the corresponding product manufacturer.
©2020 All rights reserved.
Unauthorized reproduction is not allowed in any way.
References
- HP Office Supply - Best Official HP Products & Supplies
- Laptop Computers, Desktops, Printers, Ink & Toner | HP® Official Site
- HP Office Supply - HP Office Supply
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>