FINE FIXTURES ST2W Smart Toilet Installation Guide

ST2W Smart Toilet
Installation Guide 206 Wembly Road
New Windsor, NY 12553
Phone: 718.602.6060
Fax: 718.963.2082
[email protected]
www.finefixtures.com

READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT
INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.

2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT

We reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice!
It is your responsibility to visit website to download or contact customer service for the most updated version of the installation instructions.
We shall not be liable for any injuries or property damages in connection with this product during installation or use of this product!

• LIMITED WARRANTY IS VOID ON ANY COMMERCIAL INSTALLATION.

• WE ARE NOT RESPONSIBLE FOR LOCAL CODE COMPLIANCE FOR THIS PRODUCT.

• BUILDING AND PLUMBING CODES MAY VARY FROM STATE-TO-STATE IN ACCORDANCE TO YOUR LOCATION.

• WE ARE NOT RESPONSIBLE FOR PROVIDING ANY COMPLIANCE CERTIFICATIONS.
  WE ARE NOT RESPONSIBLE TO PROVIDE ANY TYPE OF CERTIFICATIONS FOR THIS PRODUCT.

• UNDER NO CIRCUMSTANCES WE SHALL NOT BE LIABLE FOR ANY AND ALL INCIDENTAL DAMAGES SUSTAINED IN CONNECTION WITH THIS PRODUCT

• NEITHER MANUFACTURE, NOR DISTRIBUTOR, NOR RETAILER IS RESPONSIBLE FOR WATER DAMAGE OR FLOOD CAUSED DUE TO USE OF THIS PRODUCT.

• UNDER NO CIRCUMSTANCES WE SHALL NOT BE LIABLE FOR ANY AND ALL FEES, COST OF INSTALLATION/REINSTALLATION/REMOVAL, SUBSEQUENT

• DAMAGE OR TRANSPORTATION IN CASE OF THE PRODUCT DEFECT.

VANITY COMPONENTS AND HARDWARE
DURING UNPACKING THE PRODUCT AND PRIOR TO INSTALLATION INSPECT YOUR NEW PRODUCT FOR ANY DAMAGES OR MISSING PARTS.
Do NOT ATTEMPT TO INSTALL OR OPERATE THE PRODUCT IF THE PRODUCT IS DAMAGED.

TOOLS REQUIRED FOR INSTALLATION

Safety instructions

Please read the instructions carefully before installation and keep it available for future maintenance or reference.
Failure to follow these instructions can cause body injury and property damage.
Symbol Illustration
Waring Indicates that failure to follow the instruction may cause serious injury or fatality.
Caution Indicates that failure to follow the instruction may cause body injury or property damage.
Symbol Illustration

Warning

| Do not throw cigarettes and other burning stuff into toilet, otherwise
it might cause malfunction.
---|---
| Do NOT disassemble, repair or modify this product by yourself, otherwise it may cause fire or malfunction.
Do NOT pour water or detergent on the main unit or battery box plug, otherwise it may cause fire or electric shock.
Do NOT handle the battery box plug with wet hands, otherwise it may cause malfunction.
This product is factory equipped with a specific battery device.
Do NOT use any battery device other than the factory equipped battery device, otherwise it may cause fire or malfunction.
If the electric cord of battery box is damaged, it must be replaced by the manufacturer, its service center or equivalent specialist to avoid malfunction.
This product is an electric appliance, avoid direct contact with water or other liquids.
Do not position the product on its side or upside down while making electrical connections with the battery box, otherwise it may cause fire or burning.
Mandatory activities| Do not install or use the product in wet or damp locations such as a steam room.
Only use the factory equipped battery box and 1.5V “AA” alkaline battery.
When moving the product from a cold or humid environment to normal room temperature, please wait for 2 hours until the condensed water is completely volatilized to prevent electrical short-circuiting of the product.

Caution

| Do not place or store product where it can fall or be pulled into a tub or sink.
Do not place in or drop into water or other liquid.
Do NOT reach for a product that has fallen into water. Unplug the battery box immediately
Do not stand on the ceramic toilet. Do not hit the ceramic. A heavy impact on ceramic leads to damage and water leakage.
Never embed ceramic toilet base in cementitious material ( such as cement mortar). It may lead to expansion crack.
Do not stand on ceramic toilet bowl, seat and cover.
Do not use varnish thinners, gasoline, liquid chemicals, detergents, insecticides, toilet cleaners and scrubbing brush to clean the product.
Only use tap water or potable water; otherwise it may cause chafing. Exposure to direct sunlight is prohibited.
This product is equipped with soft-closing seal cover. Heavy pressing or pushing may damage the soft-closing damper.
Do not connect water supply to heater outlet. Make sure inlet water temperature at 3-35C,exceeding the specified range will result in the built-in heating module not working.
Do not lean against the seat cover when using the product to avoid damage. Do not try flushing the newsprint,diapers, sanitary napkins and other items down the toilet, which may result in toilet clogging.
If this product is malfunctioning, stop using immediately, unplug the battery box, turn off water supply, and contact the service provider.
---|---
Mandatory activities| Before installation, disassembly, repair and maintenance of the product, the power plug must be unplugged and the water supply valve must be closed.
Do not use in an environment below O °C.
If this product will not be used for an extended period of time (over 3 days), it is recommended to unplug the battery box, remove batteries, turn off water supply, and drain any water in the product.
When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:
1. This product is not intended for children (without proper adult supervision).
2. This product is not intended for individuals with reduced physical, sensory, or mental capabilities.
To prevent damage caused by freezing, please implement warmth measures to increase the temperature of the toilet.

List of materials

Technical Drawing

The product drawings are for reference only, and the company reserves the right to modify the appearance of the product without notice.

Parts Identification

Ceramic Toilet Installation

Caution before installing
• Minimum dynamic working water pressure: 0.09MPa or more (15.0L/min or more), failure to meet this pressure will not achieve the best flushing effect.
Remark: Apply the methods below if you don’t have water pressure testing device. Open the angle valve and connect water inlet for 1 Os, once the water volume is above 2.5L, the minimum water pressure of the product is ensured.

1. Installation of mating angle valve
   • Draw drain outlet centerline on the floorInstall angle valve at proper position on wall according to dimension of toilet. 

2. Cardboard installation
   • Align cardboard with the centerline of drain outlet;
   • Draw contour line according to cardboard;

3. Hose
   • Connect the water inlet and angle valve of the toilet with the matching hose and tighten it

4. Mounting bracket installation
   • Assemble the mounting bracket with bolts and then install them to the pre-installed  flange plate on the ground and lock tightwith nuts.

5. Ceramic toilet installtion
   • Install sealing flange into drain outlet; Install ceramic toilet on corresponding position according to contour line.

6. Screw installation
   • Put the screw through the fixing sleeve and then install it through the holes(on both sides of the toilet ceramic) to the mounting bracket on the ground, and lock tight with a tool;
   • Put the decorative cap on the fixing sleeve.

7. Glass cement application
   • Apply high quality mildew glass glue around the lower edge of the toilet. .

Tips:
Please make sure ceramic toilet outlet sits perfectly on drain outlet.

BEFORE INSTALLATION

1. Turn on the angle valve
   Check thread connection, make sure no leakage is found,unscrew angle valve anticlockwise to maximum opening. (Tips: When opening for the first time, the angle valve handle has a larger torque)

2. Power Connection
   Take out the battery box from the accessory kit and install 4pcs 1.5V “AA” alkaline batteries. Plug the DC plug of battery box into the DC socket of toilet and then stick the battery box to the Velcro on the bottom of the toilet.

3. Self-inspection
   After the batteries are successfully installed, the red indicator light will flash once.

Caution
When re-installing the cover of battery box, use your fingers to squeeze the side of rubber plug to exhaust air out of the box and ensure sealing.

Notes:

1. Must be 1.5V “AA” alkaline battery;
2. Different brands, different used and new batteries cannot be mixed.
3. Battery life will be significantly reduced when using non-alkaline batteries;
4. When installing the inner box components, follow the installation direction shown in the label.

INSTALLATION

Adhesive Fixing
• First connect the battery box (with batteries installed) to the main unit.

Daily maintenance

Use only a soft, damp cloth to clean. Avoid using harsh chemicals.
Note:
If the toilet is with off-seat auto flushing function, it may activate auto flushing during the cleaning.

Maintenance of filter net

1. Turn off power and the angle valve
2. Unscrew angle valve nut
3. Remove filter net
4. Use the brush to clean filter net
5. Reinstall filter and angle valve nut, turn on the angle valve and connect power,then it can work normallyafter self inspection.

Time for maintenance: It is under normal water pressure but poor flush performance occurs.

Emergency Troubleshooting

No water supply
• Put around BL water into a barrel and flush the bowl of ceramic.
Note: Avoid water spilling from bowl.Unscrew the screws on the back cover and remove back cover from the control module, replace batteries and tighten the screws again.
Pay attention to inner box direction when installing.

Replacement of battery

• Unplug the DC plug of the battery box and remove the battery box from the bottom of the toilet.
• Remove the cover of battery box and replace old batteries with new batteries, and then re-install the cover.
• Insert the DC plug of battery box into the DC socket of toilet and then stick the battery box to the Velcro on the bottom of the toilet.

When the product is left unused for long time
• Especially in winter when no one at home for a long time, please drain out the water inside tank and pipe to prevent freezing.
To discharge water

1. Drain out the water inside tank
   • Activate flushing, and then turn off angle valve to prevent water inlet.

2. Unplug and remove the battery box and then remove all batteries.

3. Drain out the water inside pipe
   • Unscrew the hose connector off angle valve, drain the water in the pipe and reinstall.

4. Handle the remaining water in bowl
   • It is suggested to put some antifreeze into water inside the bowl.

When using the toilet again, re-connect the water supply and re-install the battery box.
Caution
Before water discharging, the power must be cut off!

Technical Specification

more)–0.8MPa (static water pressure)
Installation method| Glass cement/ foundation bolts
seat| Open and close device| Quiet soft-closing device
Caring device| Automatic flushing| Toilet will automatically flush as user walks away from bowl
Low battery indication| If the battery is low, when pressing the flush button, the indicator light will flash, indicating batteries need to be replaced.
Foot-touch flushing function| Kick the foot-touch button to flush (optional)
Antibacterial position| Seat

The illustration of Main Unit Buttons

| The illustration of main unit buttons
---|---
| press the “FLUSH” button on the main unit to flush (full flush).

Notes:

1. Button light: If the battery is low, when pressing the flush button, the red light will flash.
2. Off-seat auto flushing: In the off-seat auto flushing mode, if a user is seated for 26s and <1 min, and leaves the seat for >3s, the toilet will activate a half flush. If a user is seated for > 1 min, and leaves the seat for >3s, the toilet will activate a full flush.

206 WEMBLY ROAD
– NEW WINDSOR, NY 12553
P: 718.602.6060 F: 718.963.2082
– E: [email protected]
TOLL FREE: 1.877.8FIXTURES
FINE FIXTURES.COM
TOLL FREE: 1.877.8 FIXTURES
FINEFIXTURES.COM

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>