HIKVISION DS-PDC10AM-VG3 AX Hybrid Series Wired PIR AM Curtain Detector User Manual

: June 3, 2024
: Hikvision

Table of Contents

Appearance
Installation
Resistor Wiring
Connection Type
Anti-Masking
Specification
Declaration Of Conformity
Disclaimer
FCC Statements
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HIKVISION DS-PDC10AM-VG3 AX Hybrid Series Wired PIR AM Curtain Detector User Manual

Appearance

Terminal
LED Indicator
Tamper Switch
Mode Switch
LED Jumper
Alarm:

PIR Triggered:

**Anti-Masking:

Fault:
**

Anti-masking Jumper
Direction Jumper
L→R: direction from left to right only
R→L: direction from right to left only
OFF: Turns off the direction selection

Installation

Ceiling mounting
Installation instruction

Wall mounting
Installation instruction

Mounting with the general mounting plate.

Mounting with L-mounting plate.

Resistor Wiring

Relay Status

	Normal	Intrusion Alarm	Fault	Mask
Alarm Relay	Close	Open	Close	Open
Fault Relay	Close	Close	Open	Open

Resistor Wiring

Method 1: Use the jumper to select EOL (End of Line) resistance on FAULT/TAMPER/ALARM pins.
Method 2: Add the resistor to FAULT/TAMPER/ALARM wiring ports.
Note: If EOL wiring is not used, leave the jumpers OFF. Do not force the jumper if it is not matched the pin. Method 1 & 2 should not be used on the ALARM/TAMPER at the same time.

Fault Resistance: 1K, 2K2, 6K8
Tamper Resistance: 1K, 2K2, 4K7, 5K6
Alarm Resistance: 1K, 2K2, 4K7, 5K6, 6K8

Connection Type

Note: The resistor must be connected in series with one end of the detector.
Connection Type

Normally Closed
Single End of Line Wiring
Double End of Line Wiring:
Triple End of Line Wiring:

Anti-Masking

Specification

Detection Method	Passive Infrared
Detection Range	Wall Mount: 10m

Please use the power adapter complaining with LPS. The recommended power adapter is made by Shenzhen Honor Electronic Co., Ltd.

Declaration Of Conformity

About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information here in after are for description and explanation only. The information contain din the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hik vision website (https://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professional strained in supporting the Product. and other Hik vision’s trademarks and logos are the properties of Hik vision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.

Disclaimer

TO THEMAXIMUM EXTENTPERMITTED BYAPPLICABLE LAW,THIS MANUAL ANDTHE PRODUCTDESCRIBED, WITH ITSHARDWARE, SOFTWAREAND FIRMWARE,ARE PROVIDED“AS IS”AND “WITHALL FAULTS AND ERRORS”. HIKVISIONMAKES NOWARRANTIES, EXPRESSOR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORYQUALITY, ORFITNESS FOR APARTICULAR PURPOSE. THEUSE OFTHE PRODUCT BYYOU ISAT YOUROWN RISK.IN NOEVENT WILLHIKVISION BELIABLE TOYOU FORANY SPECIAL, CONSEQUENTIAL, INCIDENTAL,OR INDIRECTDAMAGES, INCLUDING,AMONG OTHERS,DAMAGES FOR LOSSOF BUSINESS PROFITS,BUSINESS INTERRUPTION, ORLOSSOF DATA, CORRUPTIONOF SYSTEMS, ORLOSS OF DOCUMENTATION, WHETHERBASED ONBREACH OF CONTRACT,TORT (INCLUDINGNEGLIGENCE), PRODUCT LIABILITY, OROTHERWISE, INCONNECTION WITHTHE USEOFTHE PRODUCT, EVENIFHIKVISION HASBEEN ADVISED OFTHE POSSIBILITYOF SUCHDAMAGES OR LOSS.

YOU ACKNOWLEDGETHAT THENATURE OFTHE INTERNET PROVIDES FOR INHERENT SECURITY RISKS,AND HIKVISION SHALLNOT TAKEANY RESPONSIBILITIESFOR ABNORMAL OPERATION, PRIVACY LEAKAGE OROTHER DAMAGES RESULTINGFROM CYBER-ATTACK,HACKER ATTACK,VIRUS INFECTION,OR OTHERINTERNET SECURITY RISKS;HOWEVER, HIKVISIONWILLPROVIDE TIMELY TECHNICAL SUPPORTIF REQUIRED. YOU AGREETO USETHIS PRODUCTIN COMPLIANCEWITH ALL APPLICABLELAWS, ANDYOU ARESOLELY RESPONSIBLE FORENSURING THATYOUR USECONFORMS TO THEAPPLICABLE LAW.ESPECIALLY, YOUARE RESPONSIBLE, FORUSING THISPRODUCT INA MANNERTHAT DOESNOT INFRINGE ON THERIGHTS OFTHIRD PARTIES, INCLUDINGWITHOUT LIMITATION,RIGHTS OFPUBLICITY, INTELLECTUALPROPERTY RIGHTS, OR DATA PROTECTIONAND OTHERPRIVACY RIGHTS.YOUSHALL NOTUSE THIS PRODUCTFOR ANYPROHIBITED END-USES, INCLUDINGTHE DEVELOPMENTOR PRODUCTIONOF WEAPONS OFMASS DESTRUCTION,THE DEVELOPMENT ORPRODUCTION OF CHEMICALOR BIOLOGICALWEAPONS, ANYACTIVITIES IN THECONTEXT RELATED TOANY NUCLEAREXPLOSIVE ORUNSAFE NUCLEARFUEL-CYCLE, ORIN SUPPORTOF HUMAN RIGHTS ABUSES IN THEEVENT OFANY CONFLICTSBETWEEN THIS MANUALANDTHE APPLICABLELAW, THELATER PREVAILS.

This product and -if applicable -the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product toyour local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium(Cd), lead(Pb), or mercury (Hg).For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info

CAUTION

Install the equipment according to the instructions in this manual.
This equipment is not suitable for use in locations where children are likely to be present.
This equipment is suitable for use ingang box or other enclosure protected device only.
To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions.
No naked flame sources, such as lighted candles, should be placed on the equipment.
The equipment’s as been designed, when required, modified for connection to an IT power distribution system.
A readily accessible disconnect device shall be in corporates external to the equipment.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Burned fingers when handling the device. Wait one-half hour after switching off before handling the parts.
Use only power supplies at the standardof100 VAC to240 VAC,50/60 HZ.
The equipment shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the equipment.

Ensure correct wiring of the terminals for connection to an AC mains supply.

indicates hazard oust live and the external wiring connected to the terminals requires installation by
an instructed person

FCC Statements

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help. Refer to FCC 15.105 section.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with FCC radiation exposure limits set forth for general population. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Legal and Regulatory Information

UD23718B-C