TOPPING TP234A Hifi Studio79 For The Best Audio Hifi User Manual
- September 30, 2024
- TOPPING
Table of Contents
TOPPING TP234A Hifi Studio79 For The Best Audio Hifi
Contents list
- D90 ||I Discrete
- Remote control
- USB cable
- AC cable
- Bluetooth antenna
- Product Information Card
Note: You can download the driver at https://www.toppingaudio.com/downloads.
Attribute
- Measured 22.2cm x 16.0cm x 4.5cm
- Weight 1.17Kg
- Power input 100-240VAC 50Hz/60Hz
- Signal input USB/BT/OPT/COAX/AES/IIS
- Line Out output XLR/RCA
- Other connectors
- 12V Trigger In (3.5mm jack)
- 12V Trigger Out (3.5mm jack)
- Bluetooth receiving distance >10 M
- Display White OLED
- Standby power consumption <1W
- Power consumption <6.5W
Input range
- USB IN
- PCM 44.1kHz-768kHz/16bit-32bit
- DSD DSD64-DSD512 (Native) , DSD64-DSD256 (DoP)
- PEQ 44.1kHz-192kHz/16bit-24bit
- IIS IN
- PCM 44.1 kHz-768kHz/16bit-32bit
- DSD DSD64-DSD512 (Native), DSD64-DSD256 (DoP)
- COAX/OPT/AES IN
- PCM 44.1 kHz-192kHz/16bit-24bit
- DSD D8D64 (DoP)
- PEQ 44.1 kHz-192kHz/16bit-24bit
- BT IN
- AAC/SBC/APTX/APTX HD/APTX-Adaptive/LDAC
- PEQ 44.1 kHz-96kHz/16bit-24bit
Front panel
Rear panel
-
Multifunction button
-
OLEO screen
-
Remote control receiver
-
Volume knob
-
Right channel balanced XLR output
-
Left channel balanced XLR output
-
Left channel single-ended RCA output
-
Right channel single-ended RCA output
-
IIS input
-
Coaxial SPDIF input
-
Optical SPDIF input
-
Bluetooth input
-
USB input
-
AES input
-
12V Trigger IN/OUT (3.5mm jack)
The 12V Trigger IN/OUT allows the D90 111 Discrete to be activated by other devices or to activate other devices via a 3.5mm AUX cable. The upstream device connected to Trigger In can control the power on/standby of D90 Ill Discrete, and the downstream device connected to Trigger Out can be controlled by D90 Ill Discrete.
Before using the Trigger IN function, you need to press the button on the remote to set auto power on&standby mode to “AUTO: TRG”. -
Power input (AC 100-240V 50Hz/60Hz)
-
Power switch
Display
- Input
- Output
- Current sampling rate
- Volume
- PCM/DSD format indication
Remote control
The D90 Ill Discrete remote control offers both Bluetooth and infrared modes.
When the Bluetooth remote is not paired, infrared mode is enabled. The remote
indicator flashes twice when the button is pressed in infrared mode and once
in Bluetooth mode.
Pairing Bluetooth remote control
- Install two AAA batteries (not included) for the remote control.
- Connect to the power connector with the attached power cord, and turn on the unit.
- Press and hold the middle button and the C2 button until the red light flashes.
- Press and hold the knob until the display shows Pairing…
- Wait for a while, the display shows Paired which means the pairing has succeeded.
The display shows Unpaired which means the pairing has failed, please repeat the above steps.
Note:
If you need to enable infrared control, press and hold the middle button and
C2 button of the remote control until the red light flashes. Then wait for the
lights to go out and restart the unit.
- See “1. Auto power on & off setting” in the “Setup Menu”, below.
- See “2. Screen brightness setting” in the “Setup Menu”, below.
- Operation: press and hold the C1 /C2 button for 3 seconds to save the current settings, and “C1 IS SAVED” or “C2 IS SAVED” will be displayed after successfully saving. Short press the C1/C2 button to use the corresponding settings.
- What was saved: Volume and most settings in the setup menu, such as input channel, output channel, gain, etc (BT apTX excluded).
- When to use: This feature is suitable for users who have more than one usage scenario, such as the two shown below. Using C1&C2 buttons to save and load settings may free you from changing settings one by one when you want to change the usage scenario.
Connection
Connect to the input source
Support IIS, USB, Coaxial, Optical, Bluetooth, AES input.
Connect to an amplifier or active speakers
Use XLR or RCA cables to connect to amplifiers or active speakers. To avoid
damage to your devices, please turn off the amplifier or active speakers
before you connect them to D90 Ill Discrete.
Operation
Power on & off/standby operation
-
Power on & off:
Press the power switch on the rear panel to turn D90 Ill Discrete on or off. -
Standby setting:
When it is working, press and hold the button on the front panel to enter the standby state and press to exit the standby state when it is standby. Or you can press the button on the remote control to enter or exit the standby state.
Input channel switching
Press on the front panel or press the button on the remote control to switch
the input circularly.
Output channel switching
Press the button on the front panel and on the remote control to switch the
output in the cycle: RCA/ XLR / RCA+XLR.
Volume setting
-
Mute and unmute:
Press the button on the remote control to mute D90 Ill Discrete, press the mute button again, or adjust the volume to exit the mute state. -
Volume adjusting:
You can turn the volume knob or press the button on the remote control to adjust the volume. Note that long pressing the buttons on the remote control will quickly change the volume, so please be careful to protect your hearing.
Note:
Volume is fixed to 0dB in DAC mode and volume adjusting is invalid in this
mode.
Setup Menu
Enter the setup menu
After switching the power switch to “POWER OFF” , press and hold the front
panel button while switching to “POWER ON” to enter the D90 III Discrete setup
menu.
Change settings
- The knob on the front panel:
- Rotate the knob: Choose the setting item
- Press the knob: Change the setting/OK
- The remote control:
Save Settings
Please choose the 18th option of “Save and exit”.
Setting descriptions
-
Auto power on & off set
- Signal: The input signal will trigger the device to turn on, but if the current input is not connected or the input signal is invalid in 1 minute, it will automatically enter the standby state. Once having detected a valid signal, it will automatically return to a working state. (Default)
- TRG: A 12V signal will trigger the device to turn on. When D90 111 Discrete’s Trigger In is connected to another device’s 12V Trigger Out, D90 Ill Discrete’s on/standby state can be controlled through this device. The D90 Ill Discrete will remain in a standby state until Trigger In detects the signal change from 0V to 12V. When changing back to 0V, the D90 Ill Discrete will return to the standby state.
- Off: Disabled this function.
-
Screen brightness setting
- L: Low brightness
- M: Medium brightness (Default)
- H: High brightness
- A: Auto has the same brightness as Medium. The difference is that when there is no operation after 30 seconds under Auto mode, the screen will be automatically turned off and only display the current input. You can press any button to light up the screen.
-
Line Out mode setting
- PRE: Per-Amp mode, volume adjustable (Default)
- DAC: Keep the maximum volume output and the volume is not adjustable.
-
DSD Bypass
-
ON: DSD bypass enabled
-
OFF: DSD bypass disabled (Default)
Note: DSD bypass only works in DAC mode. -
Support range: DSD Native 64-256.
-
-
IIS interface phase setting
- STD: Standard phase (Default)
- REV: Reverse phase
-
DSD channel setting for the IIS interface
- LRCLK: DSDR using LRCLK (Default)
- DATA: DSDR using DATA
-
DSD flag bit setting for the I IS interface
- Pin 15: Set pin 15 as the flag bit (Default)
- Pin 14: Set pin 14 as the flag bit
-
IIS MUTE
- OFF (Default), HIGH, LOW
- Note: When using the I IS interface, noise appears when switching the sample rate, you can choose Active high/low to eliminate the noise.
-
Maximum output level at 0dBFS
- 4V (Default), 5V
-
USB protocol version setting
- UAC 2.0 (Default), UAC 1.0
-
Bluetooth setting
- ON: Bluetooth enabled (Default)
- OFF: Bluetooth disabled
- Note: Disabling Bluetooth will not affect the use of the remote control.
-
PEQ setting
- OFF: PEQ disabled (Default)
- ON: PEQ enabled
-
PEQ project
- NULL: No unit configuration (Default)
- Unused: No configuration is selected 1, 2, 3, 4, and 5 correspond to the adjusted frequency response curves for TOPPING Tune’s device configuration.
- Note: On the TOPPING Tune, you can save the local configuration of frequency response curves to the D90 Ill Discrete, and the D90 111 Discrete can use this configuration offline. Exit TOPPING Tune to switch configurations on the device.
-
BT ap TX
- ON (Default), OFF
- Note: The D90 Ill Discrete supports multiple audio coding. When set to OFF, the APTX-Adaptive coding can be disabled, allowing the use of other codecs (depending on the phone).
-
BT clear
- ON: Bluetooth enabled (Default)
- OFF: Bluetooth disabled
Note: Disabling Bluetooth will not affect the use of the remote control.
-
Channel balance setting
- Balance C: Balance (Default)
- Balance L +0.5dB: The setting range is L+0.5-1 0dB
- Balance R +0.5dB: The setting range is +0.5-1 0dB
Note: Press the button or knob to adjust. Press the remote control to restore balance.
-
Volume step
- Vol step 1.0dB: Volume step 1 dB (Default)
- Vol step 0.5dB: Volume step 0.5dB
- Note: When the volume is from -50dB to 99 dB, you can choose to step by 0.5 or 1dB, and the step above 50 dB is fixed at 0.5 dB.
-
Save settings and restart
- Save and exit: Save settings and restart
-
Factory reset
- Factory reset: Reset default
Quick menu
When it is working, press the middle button of the remote control to enter
the quick menu, the quick menu is extracted from the settings menu with 3
common settings, which includes
- PEQ setting ( 12th in the setup menu)
- PEQ project (13th in the setup menu)
- Channel balance setting (16th in the setup menu)
The way to change settings is as above, press the middle button to exit.
TOPPING Tune
-
TOPPING Tune has a PEQ adjustment that supports ten customizable frequency bands.
-
Download link of TOPPING Tune:
https://www.toppingaudio.com/download/topping-tune. -
Download the link to TOPPING Tune Reference Guide:
https://www.toppingaudio.com/download/topping-tune-reference-guide.
Troubleshooting
- If there are problems during use, please find the corresponding solutions through the following links. https://www.toppingaudio.com/faq
- If you still have problems or questions, please contact us: at service@tpdz.net.
- Finding Method: Windows OS enters the search by pressing the button at the same time (Mac OS presses the Then enter the device model to jump to FQA of the device.
Precautions
- The output jacks shall not be grounded or short-circuited.
- Do not keep the unit in a hot, humid environment or hit the unit strongly.
- Opening the case instantly voids the warranty!
- Indoor use only.
- Topping accepts no liability for any loss or damage arising directly or indirectly from the failure of D90 Ill Discrete.
- For improvement purposes, specifications are subject to changes without prior notice.
Specifications
D90 III Discrete DAC parameters (LineOut/USB In@96kHz)
Note: The above data is the result of the test in the TOPPING laboratory with an output amplitude of 5V.