Zaptec 0-160A Activation of Wago APM Installation Guide
- September 28, 2024
- Zaptec
Table of Contents
0-160A Activation of Wago APM
“`html
Product Information
Specifications:
- Product Name: Wago APM [0-160A]
- Compatibility: Zaptec Pro
- Current Range: 0-160A
- Communication Interface: Ethernet
Product Usage Instructions
A. Installation of APM
-
Connect the Ethernet cable with active internet connection to
the WAGO APM (RJ45 plug: ETH1). -
Check that all current transformers are installed on the
correct phase conductor, in the right direction, and securely
fastened. -
For WAGO APM 0-160A: Ensure that all toggle clamps on the right
side are toggled to position 1 (UP). -
Ensure that the GREY function switch on the WAGO APM is in the
upper position: RUN. -
Power up the WAGO APM.
-
Check that the LED diode marked USR on the WAGO APM flashes
green within 1-2 minutes.
B. Contact Zaptec Support
Zaptec Support requires the following information to activate
WAGO APM for Pro:
- Zaptec Portal installation name.
- MAC address for WAGO APM.
- Main fuse rating (A), to be entered into the Zaptec Portal
installation.
FAQ
Q: What should I do if the LED diode on the WAGO APM does not
flash green within 1-2 minutes?
A: Check the power connection and ensure all settings are
correctly configured. If the issue persists, contact technical
support.
Q: How do I know if the current transformers are installed
correctly?
A: Verify that the transformers are securely fastened and
aligned with the correct phase conductor as per the installation
instructions.
“`
Activation of Wago APM [0-160A] for Zaptec Pro
A. Installation of APM
1. Connection: · APM comes pre-wired for a TN grid. When connecting to an IT
grid, rewire according to Figure 1. · Current transformer cables are 5 meters
long. They should not be cut or modified. · Install the current transformer
cables on the correct phase conductor and in the direction according to the
arrow and labeling on the current transformer. · Use a 3-phase power cable
along with the supplied quick connector to power up the APM. · For the 0-160A
version, ensure that all toggle clamps on the right side are in the correct
position 1 (UP).
2. Connect the Ethernet cable with active internet connection to the WAGO APM
(RJ45 plug: ETH1). 3. Check that all current transformers are installed on the
correct phase conductor, in the right direction,
and securely fastened. 4. WAGO APM 0-160A: Ensure that all toggle clamps on
the right side are toggled to the correct position 1
(UP). 5. Ensure that the GREY function switch on the WAGO APM is in the upper
position: RUN. 6. Power up the WAGO APM. 7. Check that the LED diode marked
“USR” on the WAGO APM flashes green within 1-2 minutes.
LED light description: USR diode GREEN: Status OK WAGO APM is communicating
with Zaptec Portal ORANGE: Status Check network connection Attempting to
establish first contact with Zaptec Portal RED: Status Offline The unit
has previously been online, but cannot establish contact with Zaptec Portal 8.
Contact Zaptec Support in your country for activation.
B. Contact Zaptec Support
Zaptec Support requires the following information to activate WAGO APM for
Pro:
1. Zaptec Portal installation name. 2. MAC address for WAGO APM. 3. Main fuse
rating (A), to be entered into the Zaptec Portal installation.
– 1 –
Activation of Wago APM [0-160A] for Zaptec Pro
Figure 1: Rewiring for the IT grid
The O2 cable running between N on the power supply and the N-terminal block,
the latter connection must be moved to the terminal block for L2 or L3 to
supply voltage to the power supply.
GREY function switch: Set to the RUN position
WAGO APM 0-160A version: Toggle clamps in position 1 (up)
– 2 –