maytronics 8152200 Dolphin Wave 100 Pool Cleaner Instruction Manual

: September 27, 2024
: maytronics

Table of Contents

8152200 Dolphin Wave 100 Pool Cleaner
Specifications
Product Information
Operating Instructions
1. Introduction
2. Specifications
3. Warnings and Cautions
- Pool Cleaner Parts
5. Using the Pool Cleaner
Q: How often should I clean the filter bag?
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

8152200 Dolphin Wave 100 Pool Cleaner

“`html

Specifications

Motor protection: IP 68
Minimum depth: 0.4 m (1.33 ft)
Maximum depth: 5 m (16.4 ft)

Product Information

The Dolphin WAVE 100 Pool Cleaner by Maytronics is a robotic
pool cleaner designed to provide reliable, convenient, and
cost-effective pool cleaning. It features reliable filtration in
all pool conditions and an all-surface climbing brush for maximum
pool hygiene. The cleaner delivers advanced cleaning technology,
long-lasting performance, and easy maintenance.

Operating Instructions

1. Introduction

Thank you for purchasing a Maytronics Robotic Pool Cleaner. Your
cleaner ensures reliable pool cleaning with advanced technology and
easy maintenance.

2. Specifications

The specifications for the Dolphin WAVE 100 Pool Cleaner are as
follows:

Motor protection: IP 68
Minimum depth: 0.4 m (1.33 ft)
Maximum depth: 5 m (16.4 ft)

3. Warnings and Cautions

Warnings: Ensure proper supervision and
instruction for users with limited capabilities.

Pool Cleaner Parts

The Dolphin WAVE 100 Pool Cleaner comes with the following
parts:

Combined Brush
Wonder Brush (optional)
Bottom lid and filter bag
Caddy
Remote Control Unit
Filter bag options: Fine, Ultra fine, Disposable filter bag x
5
Power Supply Unit

5. Using the Pool Cleaner

5.1 Set Up

Before using the Pool Cleaner for the first
time:

Unwind the cable and remove plastic coverings.
Attach the floating cable to the power supply.

5.2 Putting the Pool Cleaner into the pool

Soak foam climbing rings in water if dry.
Release trapped air by shaking or turning the robot upside
down.

5.3 Removing the Pool Cleaner from the pool

To remove the Pool Cleaner:

The robot will shut off automatically at the end of the
cleaning cycle.
Turn OFF and unplug the power supply before removing the
cleaner from the pool.

FAQ

Q: How often should I clean the filter bag?

A: It is recommended to clean or replace the filter bag after
every use to maintain optimal performance.

“`

Dolphin WAVE 100 Pool Cleaner
Operating Instructions
8152200

Dolphin WAVE 100 Robotic Pool Cleaner Operating Instructions

Contents
1. INTRODUCTION ……………………………………………………………………… 2 2. SPECIFICATIONS …………………………………………………………………….. 2 3. WARNINGS AND CAUTIONS…………………………………………………… 2
3.1. Warnings ………………………………………………………………………… 2 3.2. Cautions …………………………………………………………………………. 2 4. POOL CLEANER PARTS……………………………………………………………. 3 5. USING THE POOL CLEANER……………………………………………………. 4 5.1. Set up …………………………………………………………………………….. 4 5.2. Putting the Pool Cleaner into the pool …………………………….. 5 5.3. Removing the Pool Cleaner from the pool ……………………….. 5 5.4. Maintenance …………………………………………………………………… 6 5.5. Off-season storage………………………………………………………….. 7 6. POWER SUPPLY ……………………………………………………………………….. 8 7. REMOTE CONTROL UNIT ………………………………………………………. 9 CADDY ASSEMBLY ……………………………………………………………………… 11

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

1

Dolphin WAVE 100 Pool Cleaner
Operating Instructions
1. INTRODUCTION
Thank you for purchasing a Maytronics Robotic Pool Cleaner. We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and cost effective pool cleaning. Its reliable filtration in all pool conditions and all-surface climbing brush enhance maximum pool hygiene. The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technology, long lasting performance and easy maintenance.
2. SPECIFICATIONS
Motor protection: IP 68 Minimum depth: 0.4 m (1.33 ft) Maximum depth: 5 m (16.4 ft)

3. WARNINGS AND CAUTIONS

3.1. Warnings

CAUTION

· Use the originally supplied power supply only · Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth
leakage interrupter (ELI) · Keep the power supply out of standing water · Position the power supply at least 3.5 m (12 ft) away from the edge of the pool · Do not enter the pool while the pool cleaner is working · Unplug the power supply before servicing · Keep the Robotic Pool Cleaner out of the reach of children or persons with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

3.2. Cautions
When not in use store the Pool Cleaner on the Caddy in a shaded area. Use the Pool Cleaner in the following water conditions only:

Chlorine pH Temperature NaCl

4 ppm max. 7.0 7.8 6 °C 35 °C (43 °F 95 °F) 5000 ppm max.

2

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

4. POOL CLEANER PARTS
Dolphin WAVE 100
Combined Brush All surface climbing brush ideal for most pool surfaces
Wonder Brush For smooth ceramics (optional)
Bottom lid and filter Bag

Caddy Remote Control Unit

Filter bag options: Fine – factory default Ultra fine – extra Disposable filter bag x 5

Power Supply Unit

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

3

5. USING THE POOL CLEANER
5.1. Set Up
Before using the Pool Cleaner for the first time perform the following steps.
Unwind the cable and stretch it out completely so that it has no kinks.

Remove the plastic coverings before use.

Attach the floating cable to the power supply by inserting it with the notch on the connector (1) lined up with the groove in the socket on the power supply and turning clockwise (2).

(‘&-

40°C Max 104°F Max

N GU

Change diagonal handle position for water line sideway movement. To adjust the handle angle:
A. Press the latch down and hold it in position.
B. Move the handle to the desired position and release the latch to hold the handle in place.

1,2: Normal advance More efficient cleaning action on water-line.
3,4: Fast advance Fast speed for faster but less efficient cleaning action on water-line.

4

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

5.2. Putting the Pool Cleaner into the pool
If the foam climbing rings on the brushes are dry soak them in water until soft.
Shake the robot from side to side or turn it upside down to release trapped air. Let it sink to the pool floor.
ON
Turn the power supply ON.
5.3. Removing the Pool Cleaner from the pool
The robot will perform automatic shut-off at the end of the cleaning cycle.
OFF
Turn OFF and unplug the power supply.
CAUTION

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

5

B C
Using the floating cable, bring the Pool Cleaner to the pool’s edge. DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.
5.4. Maintenance
Clean the filter bag with a hose. Periodically clean the brushes with a hose. It is recommended to periodically wash the filter bag in a washing machine. Use gentle cycle program.

6

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

Cleaning the impeller
Unplug the power supply.
If you notice debris trapped in the impeller, open the impeller and remove the debris.

Cable
To remove the kinks, stretch the cable out completely and let it sit for at least a day in the sun.
5.5. Off-season storage
If the pool cleaner will not be in use for an extended period, perform the following storage steps: · Make sure that no water is left in the pool cleaner · Thoroughly clean the filter bag and insert in place · Roll up the cable so that it has no kinks and place on
the Caddy · Store the pool cleaner upright on the Caddy in
a protected area out of direct sun/rain/frost at a temperature of between 5 °C 45 °C (41 °F 113 °F)

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

7

6. POWER SUPPLY

Digital “Switch-Mode” Power Supply with full filter bag and delay indicator.

· Input – 100 VAC 250 VAC

· 50 Hz 60 Hz

<30 VDC; IP 54

· 180 W

· Output – <30 VDC

· IP 54

Delay indicator Full filter bag indicator

<30 VDC; IP 54

On/Off switch

Reset button

Full filter bag indicator and Reset button
The power supply is equipped with a filter bag status indicator. The red LED indicates two filter conditions. · When blinking – The filter is partially blocked. · When lighted – The filter is blocked and must be emptied and cleaned. If the LED does not turn off after the filter bag had been emptied and cleaned, press the RESET button while the robot is working.
Delay indicator
The power supply is equipped with a Delay indicator that indicates if the Delay option is activated (through the remote control unit).

8

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

7. REMOTE CONTROL UNIT
The Control Panel
The remote control unit (RCU) offers two operation modes Automatic mode and manual direction control mode. In automatic mode, the cleaning parameters can be changed. In manual direction mode, the robot’s motion can be controlled manually.

Radio reception meter When no black lines are showing, move closer to the power supply unit Battery level meter When flashing, change the batteries Manual control indicator When flashing, you are in manual direction control mode
Cleaning cycle icons
Delay timer icons
Cleaning mode icons
ON/OFF button
Manual/automatic select button
Set/OK button
Direction control arrows

Manual Direction Control Mode
1. Press the On/Off button once. The remote control will start in manual direction control mode.
2. Use the direction control arrows (see right) to control the movement of the robot around the pool.
Exiting Manual Direction Control Mode and setting the Automatic Mode
1. To exit the manual direction control mode, press the Manual/Automatic select button once only.
2. The digital screen will light up and three rows of function icons will be displayed in default mode.
1. To change the parameters press the up or down arrows. 2. To select the parameter settings use the right or left arrows.
When you reach the required function press the Set/OK button.

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

9

Press the Manual/Automatic select button and then choose the desired parameters according to the following table:

Cleaning cycle indicator This determines the length of the cleaning cycle.

Fast 4-hour cycle

Efficient 6-hour cycle for everyday use. (Default setting)

Extra 8-hour cycle

Delay time indicator This determines when the pool cleaner starts to work. Delaying allows the dirt to settle to the bottom of the pool.

Immediate start (Default setting)

One-hour delay

Two-hour delay

Cleaning action indicator Allowing you to choose from the following options.

Standard Floor and wall cleaning. (Default setting)

Ultra-clean Stronger suction and slower movement. (floor and wall)

Floor only Cleans only the floor and the area where the floor and walls meet

Walls only Cleans walls and waterline only

Note:
· After 2 minute if no button is pressed, the Remote Control Unit will shut- down and the Pool cleaner will continue to work in the previous settings.
· When the “Ultra-Clean” and “Walls Only” options finish their cycles, the Pool Cleaner will return to default settings.

10

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

Dolphin WAVE 100 Pool Cleaner Caddy assembly

Dolphin WAVE 100 Pool Cleaner | Operating Instructions

11

1

2

4

3a

3b

4

4a