maytronics M700 Robotic Pool Cleaner User Guide

: May 15, 2024
: maytronics

Table of Contents

Thank You
Caution & Warnings
Recommendation
Operating The Robot Using The MyDolphin™ Plus App
Maintenance
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

maytronics M700 Robotic Pool Cleaner

maytronics M700 Robotic Pool Cleaner

Thank You

For purchasing a Maytronlcs Dolphin Robotic Pool Cleaner.
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologies, long lasting performance and easy maintenance. You and your family will be free to enjoy swimming with full confidence that your pool is completely clean.

Caution & Warnings

Use the origin ally supplied power supply only.
Do not use an extension cable in any case whatsoever.
Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter.
Ensure that the power supply is not in a wet environment.
Do not enter the pool while the pool cleaner is in the water.
Unplug the power supply before servicing.
Do not use the cable to take the pool cleaner out of the water.
Use the Pool Cleaner in the following water conditions only: Chlorine Max 4 ppm; pH 7.0 – 7.8; Temperature 6 -35°( (43-95°F); NaCl Maximum== 5000 ppm.
Keep the Robotic Pool Cleaner out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

Digital Power Supply Input 100–250 AC Volts 50-60 Hertz 2A output: <30 VDC 6A 1aow IP S4

Specifications:

Motor protection : IP 68
Minimum depth : 0.4m/133ft
Maximum depth : 5m/16.4ft

Recommendation

The power supply should be placed 1n a well ventilated and shaded location.
If the Dolphin n is fitted with combined or wonder brushes gently squeeze the brushes until they are soaked with water and only then start the cleaning process .
Release minimal required floating cable length to ensure proper pool cove rage. leave excess cable rolled outside the pool.
After each cleaning cycle wash the filters or cartridge Clogged filters reduce scanning and cleaning efficiency.
In case the cable has some kinks stretch it out completely and l2t ft sit for at least a day in the sun.
Store the pool cleaner in a shady place on the caddy.

Operating The Robot Using The MyDolphin™ Plus App

Plug in the power supply.
Download the My Dolphin TM Plus app.
Activate Bluetooth® and Wi-Fi on your smart device.
Start the registration process.
Scan the QR code printed on the power supply, and complete the process.
Follow the instructions as showed in the app.

Symbol Robot Operation

Set Up

Connect the floating cable to the power supply.
Position the power supply at least 3.5m/12ft away from the edge of the pool.

Into Pool
Put the pool cleaner in the pool and let it sink to the floor.
Make sure that the floating cable is free of any obstructions.

Operation
Turn the power supply ON.
The pool cleaner will now operate until it has reached the end of the cleaning cycle.

Out of the pool
Use the robot’s handle to pull it out from the pool.
Cleaning the filter
It is highly recomended to clean the filter basket after ,each cleaning cycle.
Note : Don1t let the filter cartridges dry out before cleaning.
Unplug the power supply before servicing.
Open the robot’s cover.

Lift the basket.

Op[en the latch to release the bottom lid in order1oi remove the debris.

Clean the filter basket with a hose.
Storage
Coil the cable and store in a coot, dry place.
Do NOT store the robot and its accessories where it will be exposed to direct sunlight, excessive heat or to frost.

Maintenance

Periodic filter cleaning

Dismantle the 4 ultra-fine filter panels of the outer basket according to the following steps:

Hold down the handle and remove the inner net.
Dismantle the panels, starting with pressing on panel no.1 using your thumbs.
Continue to dismantle the panels in the order of their numbers: no.2–> no.3–> no.4.
Insert the clean filter basket and close the robot’s cover.