ACV 42XVX006-0 Steering Wheel Control Interface Installation Guide
- September 27, 2024
- ACV
Table of Contents
- ACV 42XVX006-0 Steering Wheel Control Interface
- VEHICLE APPLICATION
- KEY FEATURES
- PRIOR TO INSTALLATION
- WIRING KEY
- FLYING WIRE WIRING KEY OUTPUTS & RATINGS
- DIPSWITCH 5 & 6
- SWC INTERFACE
- CONNECTION GUIDE
- INSTALLATION
- STEERING WHEEL CONTROL CONFIGURATION
- BUTTON REMAPPING
- CONNECTION DIAGRAM
- Product Specifications:
- Product Usage Instructions:
- Frequently Asked Questions (FAQ):
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ACV 42XVX006-0 Steering Wheel Control Interface
INSTALLATION GUIDE
The 42XVX006-0 allows for the retention of the steering wheel controls as well as other vital features when installing an aftermarket unit into the vehicle. This interface features selectable dipswitches for dedicated applications, simply refer to the provided table for the correct configuration ensuring seamless integration.
VEHICLE APPLICATION
OPEL / VAUXHALL
- Movano B (X62): 2013 – 2021
- Vivaro B (X82): 2014 – 2019
KEY FEATURES
- RETAIN STEERING WHEEL CONTROL FUNCTIONALITY
- REPLACE FACTORY RADIO
- OUTPUT FOR SPEED PULSE
- SOFTWARE UPDATEABLE
- REMAPPABLE BUTTONS
PRIOR TO INSTALLATION
Installation requires a certain level of technical knowledge. Prior to installation, it is important to read the manual. Select a location for installation that is dry and free from heat sources. It is essential to use the correct tools during installation to prevent any damage to the vehicle or the product itself. Please note that we cannot be held liable for any issues arising from improper installation.
Before proceeding with installation, disconnect the negative battery terminal and ensure the key is removed from the ignition.
WIRING KEY
ISO CONNECTOR WIRING KEY
- Purple Right Rear Speaker +
- Purple/Black Right Rear Speaker –
- Green Left Rear Speaker +
- Green/Black Left Rear Speaker –
- Grey Right Front Speaker +
- Grey/Black Right Front Speaker –
- White Left Front Speaker +
- White/Black Left Front Speaker –
- Yellow Permanent 12V
- Black Ground
- Red Ignition 12V
- Orange Illumination
FLYING WIRE WIRING KEY OUTPUTS & RATINGS
Pink: Speed Pulse – 0 to 12V Square Wave @ 1Hz/Kph
Standby Current <3mA Operating Voltage 6V to 16V Operating Temperature -20C to
85C
*rated at 25 degrees Centigrade
DIPSWITCH 5 & 6
Dipswitch 5 & 6 are reserved for vehicle specific configuration
KEY1 and KEY2| KEY1 and KEY2 are specifically tailored for analog learning
mode-style radios. Our SWC module is designed with a resistor chain that
precisely matches the required resistance for seamless compatibility with this
type of head unit.
---|---
KEY1 and KEY2 EXTEND| This mode extends every button press to 2 seconds during
the learning process. However, with rolly wheel-designed steering wheel
buttons, holding for 2 seconds isn’t feasible. Our KEY1 and KEY2 extend
feature addresses this by automatically prolonging each press, simplifying
head unit programming even in such scenarios. Extend mode is not intended for
normal use, it is only used in the teaching process.
ANALOG SINGLE WIRE and ANALOG SINGLE
WIRE EXTEND| This function operates similarly to KEY1 and KEY2 but transmits
all unique values through the IR SWC single wire. This is crucial for
compatibility with learning-style head units featuring only one learning input
wire. To ensure compatibility, we’ve incorporated this feature into our
steering wheel control interface, ensuring seamless operation across various
head unit setups.
The Analog Extend mode functions identically to its counterpart within the
KEY1 and KEY2 system but transmits through a single wire.
SWC INTERFACE
CONNECTION GUIDE
BEFORE INSTALLATION
Prior to installing the interface, it is essential to remove and disconnect the factory stereo. For guidance on this process, please refer to the vehicle owner’s manual/handbook or seek assistance from a professional.
SETTING THE DIPSWITCHES
This interface includes a set of dipswitches. Consult the dipswitch selection guide to select the appropriate configuration. To activate a dipswitch, press it downward into the ‘ON’ position. Refer to the diagram for an example of the ‘KENWOOD1’ dipswitch configuration.
INSTALLATION
1. Take the interface, then connect the 16-PIN head unit connection lead and
the 18-PIN steering wheel harness connectors to their respective ports.
2. Connect the head unit connection lead to the steering wheel remote input
on the rear side of the aftermarket stereo.
Connection methods vary based on the stereo brand, utilising either a 3.5mm
jack connector SWC IR wire or wired inputs KEY1 and KEY2.
For specific connection guidance, refer to your aftermarket stereo’s
installation manual if not clearly labelled on the stereo harness.
3. Connect the power/speaker ISO connector from the interface to the
corresponding power/speaker ISO connection on the aftermarket stereo.
For aftermarket stereos lacking an ISO connector, refer to the “Wiring Key” on
Page 2 for guidance on connecting wires. Certain interfaces may also include
extra “flying” wires for additional functionalities such as parking brake
trigger, reverse gear, and speed pulse. Further information on these wires is
available in the “Flying Wire Wiring Key” section.
4. Connect the vehicle-specific connectors from the interface harness to the
corresponding connectors on the vehicle harness.
5. Connect the flying wires on the harness to the rear of the stereo (iff
applicable).
6. Connect the antenna adapter to the vehicle’s existing connection at the
rear of the aftermarket stereo.
7. When installing an aftermarket reverse camera, connect the yellow RCA from
the harness to the yellow RCA of the aftermarket camera. (If supported by the
interface and vehicle)
8. When installing a DAB antenna, ensure to connect the DAB aerial connector
to the rear of the new stereo.
9. After connecting all wires (along with any additional accessories), it’s
crucial to thoroughly test the stereo and steering wheel controls before
reassembling the dashboard. If steering wheel controls are unresponsive,
inspect connections and check dipswitch settings. Repeat the connection
process if necessary, following the outlined steps.
STEERING WHEEL CONTROL CONFIGURATION
BUTTON REMAPPING
The steering wheel buttons listed offer the flexibility of being re-configured or assigned dual functions. The availability of these buttons depends on the specific vehicle to which the interface is being installed and if the aftermarket radio supports them.
In addition to button remapping, we offer the option to assign dual functions to each button on the steering wheel. This means that every button can be programmed to execute both a short press command and a long press command.
You can also add your own bespoke configuration. Button configuration can be
done by PC, MAC and smart phone via the USB port.
Button Remapping instructions can be found in a separate guide on our website.
CONNECTION DIAGRAM
HEAD UNIT CONNECTION LEAD
SWC INTERFACE
SWC VEHICLE HARNES
Product Specifications:
- Product Name: Steering Wheel Control Interface for Opel/Vauxhall Vehicles
- Model Number: 42XVX006-0
- Compatible Vehicles: OPEL / VAUXHALL Movano B (X62) 2013 – 2021, Vivaro B (X82) 2014 – 2019
- Key Features: Retention of steering wheel controls, selectable dipswitches, seamless integration
Product Usage Instructions:
Prior to Installation:
Installation requires technical knowledge. Read the manual carefully. Choose a dry location free from heat sources. Use correct tools to prevent damage. Disconnect the negative battery terminal and remove the key from the ignition.
Wiring Instructions:
Refer to the provided wiring key for ISO connector and flying wire connections:
- Purple: Right Rear Speaker +
- Purple/Black: Right Rear Speaker –
- Green: Left Rear Speaker +
- Green/Black: Left Rear Speaker –
- Pink: Speed Pulse – 0 to 12V Square Wave @ 1Hz/Kph
- Grey: Right Front Speaker +
- Grey/Black: Right Front Speaker –
- White: Left Front Speaker +
- White/Black: Left Front Speaker –
- Yellow: Permanent 12V
- Black: Ground
- Red: Ignition 12V
- Orange: Illumination
Standby Current:
Ensure standby current is maintained for proper functionality.
Frequently Asked Questions (FAQ):
Q: What should I do if the steering wheel controls are not working after
installation?
A: Check the wiring connections and ensure they are properly connected based on the provided wiring key. Recheck the dipswitch configuration for correct settings.
Q: Can this interface be used on other vehicle models?
A: This interface is specifically designed for OPEL/VAUXHALL Movano B (X62) and Vivaro B (X82) models within the specified years.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>