acv 42ct multilead3 Multilead Connection Cable for Steering Wheel Adapter Instruction Manual
- June 4, 2024
- ACV
Table of Contents
acv 42ct multilead3 Multilead Connection Cable for Steering Wheel Adapter
Scope of delivery
Connector Interface
12-Pin Micro-Fit > 4-Pin Molex Mini-Fit (A)
Intermediate cable HU (with blocking diode)
for: Pioneer AVH / DMH / SPH 2021/2022> 4-Pin Molex Mini-Fit > 4-Pin Molex
Mini-Fit (B)
Connector Head Unit (HU)
4-Pin Molex Mini-Fit > 3,5 mm Klinkenanschluss / Jack connection (C)
Connector Head Unit (HU)
4-Pin Molex Mini-Fit > 3-Kabel Anschluss / 3-Cable connection (D)
Configuration Connector
The configuration of the Multilead3 is carried out by removing the coloured cable Jumper J1 / J2 / J3 in connector A and using the connector head unit (HU) B C D (included in delivery).
Alpine 3,5 mm Klinke/Jack
- Remove the cable jumper J2 (green)
- Use HU connector C
Clarion 3,5 mm Klinke/Jack
- Remove the cable jumper J3 (purple)
- Use HU connector C
Blaupunkt 2010 > · China HU · JVC Kenwood 2017> · LG · Pioneer · Sony 3,5 mm Klinke / Jack
- Don’t remove any cable jumper
- Use HU connector C
Note
Self-learning HU Blaupunkt · China HU · Kenwood · Sony: The steering wheel
remote control function must be configured according to the manual of the HU
manufacturer.
Pioneer AVH / DMH / SPH 2021/2022 > 3,5 mm Klinke / Jack
- Don’t remove any cable jumper
- Use the intermediate cable B and the HU connector C
For these and other Pioneer HUs
Pioneer AVH
- Pioneer AVH-A240BT
- Pioneer AVH-A240DAB
Pioneer DMH
- Pioneer DMH-A240BT
- Pioneer DMH-A241BT
- Pioneer DMH-A340DAB
- Pioneer DMH-A245BT
Pioneer SPH
- Pioneer SPH-DA160DAB
- Pioneer SPH-DA360DAB
JVC 3,5 mm Jack / 1 wire connector
- Remove the cable jumper J2 (green) and J3 (purple)
- Use HU connector C or D
Note
Use Key 1 (brown) D for 1 wire connection. Insulate Key 2 (white) and GND
(black).
Kenwood 1 wire connector
Remove the cable jumper J1 (orange) and J2 (green)
Note
Use Key 1 (brown) D for 1 wire connection. Insulate Key 2 (white) and GND
(black)
Panasonic 1 wire connector
Remove the cable jumper J1 (orange)
Note
Use Key 1 (brown) D for 1 wire connection. Insulate Key 2 (white) and GND
(black)
Beat · Nakamichi · Philips 1 wire connector
Remove the cable jumper J1 (orange) and J3 (purple)
Note
Use Key 1 (brown) D for 1 wire connection. Insulate Key 2 (white) and GND
(black)
XZent · Zenec 1 wire connector
Connect J1 · 12 (orange) with J2 · 10 (green). Remove cable Jumper J3
(purple)
Note
Use Key 1 (brown) D for 1 wire connection. Insulate Key 2 (white) and GND
(black)
Blaupunkt 2010 > · China HU · ESX Kenwood 2020> · Snooper · XZent
2 wire connector / 3 wire connector
Note
Self-learning HU
Connection according to the manual of the HU manufacturer. The steering wheel remote control function must be configured according to the manual of the HU manufacturer. Insulate unused wires.
An appropriate installation in observance of these operating instructions is necessary. Please make sure the wiring is arranged so it is not bent or crimped due to the risk of a cable break. Make sure that all connections are correct. Route the cable away from moving parts, do not allow the cable to be entangled, pinched, or damaged in any way. We will not be liable for damage due to improper installation or utilization. Use the specified accessory parts to prevent product failure. Subject to technical modifications; no responsibility is accepted for the accuracy of this information.