acv 42spg020 Steering Wheel Control Interface Instruction Manual
- May 15, 2024
- ACV
Table of Contents
42spg020 Steering Wheel Control Interface
Steering Wheel Control Interface 42spg020
You will find detailed information about vehicle models, connection and
functions in our web store at https://shop.acvgmbh.de Enter the article
number in the search field. This will take you to the item description.
For Peugeot Vehicles whithout Parking Sensors and Original Single DIN Radio.
Retains Steering Wheel Controls and USB.
Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for
installation. The place of installation must be free of moisture and away from
heat sources. Please ensure you use the correct tools to avoid damage to the
vehicle or product.
ACV GmbH can not be held responsible for the installation of this
product.
Wiring Colour Codes
Wire Colour | Function |
---|---|
Yellow | Permanent 12V |
Black | Ground |
Red | 12V Ignition |
Orange | Illumination |
Pink | Speed Pulse |
Green | Park Brake |
Purple/White | Reverse |
Purple | Right Rear Speaker + |
Purple/Black | Right Rear Speaker – |
Green | Left Rear Speaker + |
Green/Black | Left Rear Speaker – |
Grey | Right Front Speaker + |
Grey/Black | Right Front Speaker – |
White | Left Front Speaker + |
White/Black | Left Front Speaker – |
Antenna Adapter
Din Connector | Connection to the aftermarket radio |
---|---|
Blue | Antenna/Amp Remote |
Fakra Connector | Connection to the vehicle radio plug |
USB Adapter
HSD plug blue to the car
USB Stecker
Aftermarket Radio
DISCLAIMER
The information contained in this document may vary without notice if changes are made to the product(s). These instructions are based on documented data and tests. ACV GmbH cannot be held responsible for changes in vehicles (e.g. software updates, hardware replacement) for damage that may result from the installation of this product.
Installation
Before installing the Stalk adapter, the factory radio must be removed and
disconnected. Please refer to the vehicle’s operating instructions/manual or
consult a specialist. A connection cable (lead) to the radio for the steering
wheel control is also required for installation (available separately).
Please make sure you have the correct cable before proceeding. With a
universal lead/cable, prepare the cable loops according to the instructions.
-
Connect the 12 way molex connector of the head unit patch lead(supplied separately) to the interface. Further information can be found in the connection diagram on page 3.
-
Connect the other end of the lead/cable to the steering wheel control input on the rear of the aftermarket radio.
NOTE : Depending on the make of the aftermarket radio, this may be a 3.5 mm jack plug or a cable input.
Please refer to the installation manual of the aftermarket radio for more information.
Important: This step must be carried out before the LFB adapter is connected to the power supply. -
Connect the 14-pin plug of the supplied wiring harness to the LFB adapter.
-
Connect the ISO power/speaker plug to the aftermarket radio.
For the function e.g.: Actuating the parking brake, reverse gear and speed impulse, the “Additional connections” must be connected (see connection diagram on page 3). -
Connect the Quadlock plug of the supplied wiring harness to the plug of the vehicle to.
-
To retain the vehicle antenna, plug in the corresponding Fakra housing in the OEM Fakra in the vehicle.
-
Connect the antenna plug to the aftermarket radio and make sure that the blue cable is connected to the antenna voltage.
-
Test the function and steering wheel controls before reinstalling the radio.
If the steering wheel control does not respond, uninstall the interface and repeat the steps described above. For further help and support, please contact us directly at support@acvgmbh.de
Steering wheel buttons
Wiring Diagram
ACV
GmbH
Straßburger Allee 10-12
41812 Erkelenz
Germany
Fon (02431) 9645-0
Fax (02431) 9645-55
Mail: info@acvgmbh.de
Web: www.acvgmbh.de
ArtNr.:42spg020
Date: 12/2023
Rev: 1