COMMSCOPE CC200 Fiber Optic System Installation Guide

: September 27, 2024
: CommScope

Table of Contents

About this manual
General product information
Overview organizer
Abbreviations
Tools
Warnings and Cautions
Kit contents
Closure preparation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**COMMSCOPE CC200 Fiber Optic System Installation Guide

**

About this manual

This manual describes the basic installation steps of the Compact Closure 200. The document starts with providing an overview of the tools required to perform the installation. Also warnings and cautions are indicated, which should be observed before starting the product installation.

Installation steps in this document are limited to: closure preparation, organizer preparation, feeder cable preparation and installation, storing feeder fibers, closing the closure and mounting the closure. For the installation steps required for the branch application, refer to TC-1547-IP- BR: CC 200 Branch application. For the installation steps required for the splice application, refer to TC-1547-IP-SP: CC 200 Splice application. For the installation steps required for the patch application, refer to TC-1547-IP-PA: CC 200 Patch application. For the installation steps required for the flat ribbon application, refer to TC-1547-IP-FLR: CC 200 Flat Ribbon application.

Images in this manual are for reference only and are subject to change.

General product information

Dimensions

Cable diameter range

Position|
---|---
mm| Inches
Feeder cable| ≤18| ≤ 0.71
Branch cable| ≤18| ≤ 0.71
Single drops| ≤ 8 (flat cable: 8 x 4,5)| ≤ 0.32 (flat cable: 0.32 x 0.18)
Dual drops| ≤ 6,2| ≤ 0.25
Cable retention module| Cable diameter (mm/Inches)| Cable capacity
---|---|---
Rear side| Front side Drop
Feeder| Branch
NVX-CR-SA-LA-NN| 6-18 / 0.24-0.71| 2| 2| –
NVX-CR-TI-SM-NN NVX-CR-SA-SM-NN| ≤ 8 / 0.32| –| 4| 12
NVX-CR-MC-RD-NN| 4-6,2 / 0.16-0.25| –| 4| 12
NVX-CR-MC-FT-NN| flat: 8×4,5 / 0.32×0.18| –| 4| 12
NVX-CR-DU-FL-NN| ≤6,2 / 0.25| –| –| 24

Overview organizer

Loop storage basket
Subunit transition zones
Feeder/ Branch Cable retention
Drop Cable retention
Patch area or drop feed through (depending on application)
Pocket
Splice trays
Tower

Abbreviations

CC: Compact Closure
UMB: Universal Mounting Bracket

Tools

Warnings and Cautions

Follow the installation instruction steps to ensure the performance of the closure. It is necessary to take
precautions and keep the working space clean to protect the closure sealing materials and splices.
Exposure to laser radiation can seriously damage the retina of the eye. Do not look into the ends of any optical fiber. Do not assume the laser power is turned off or that the fiber is disconnected at the other end. Looking into the ends of any optical fiber is entirely at your own risk. A protective cap or hood MUST be immediately placed over any radiating adapter or optical fiber connector to avoid the potential of dangerous amounts of radiation exposure. This practice also prevents dirt particles from entering the connector and adapter.
Fiber optic cables may be damaged if bent or curved to a radius that is less than the recommended minimum bend radius. Always observe the recommended bend radius limit when installing fiber optic cables, subunits and patch cords.

Kit contents

N°	Description	Qty		N°	Description	Qty
1	Closure with organizer	1		5	Cable ties	2×6
2	4 Feeder cable retention kits (NVX-CR-SA- LA-NN) including 4 strips of
silicone tape of 2,5 cm / 1 Inch width	1		6	Demarcation cover security
screws	2
3	Drop cable retention kits (24 cable ties + 12 strips of silicone tape of
1,25 cm /0.5 Inches)	1		7	Tube holders	12
4	Octopus™ gel blocks	1×3		8	Yellow snaps	4

Note: Contents can vary depending on the configuration.

Closure preparation

Open the packaging box

Open the packaging box and verify the kit contents.

Kits and accessories are stored on the top layer. The essential parts under which the Octopus™gel blocks and the yellow snaps, are stored in the side compartment. The closure with organizer is stored under the accessory shelf.

Open the latches

To open the closure, open the latches. Start with the front latch (1). Then continue opening the latches front side to backside. When opening the front latch, pull the metal part a bit frontwards to avoid that it gets stuck when opening the cover.
Rotate the cover. Verify the long seal remains correctly seated within the closure cavity

Access the inside of the closure

Open the closure, lift the cover up.
Hinge the cover open to the side of the installed hinge.
Secure the cover in open position: the cover with hinges will move downwards and will lock into the base.

Note: If the hinges are installed in the top position, the cover cannot be secured in open position. To access the inside of the closure, the cover should be detached.

Install the hinges in another position

The hinges are pre-installed on the left side. However it is possible to install them in another position. First the hinges should be removed.

Remove the hinge lock

Remove the lock of the hinge in the base. Use a screw driver to push the snap hook backwards.
Then slide the lock downwards to remove it.

Remove the hinges

Remove the cover from the base.
a Push on the snap features under the hinge on the base.
b Slide the cover with the hinges over the snap features.
Use a screw driver to disassemble the hinges from the cover.
Lift the hinges up and then remove.

Re-install the hinges

The hinges can be installed on the left, right or at the top of the cover.

Slide the hinge into the openings of the cover.
Then slide the hinge down in its lock position.
Assemble the cover and base by sliding the cover hinges into the cavities within the base. The hinges are properly seated in the base if a clicking sound is noticed.
Rotate the cover towards the base and close the cover.
Re-install the lock of the hinge in the base.
Lock installed

Remove the organizer (first day)

Lift the bottom part of the organizer frontwards.
Slide the organizer downwards to release it from the top snap hooks.

Note: This is the first day procedure only. For re-entry see section Re- entry on page 24

Install the yellow snaps

Push the 4 snaps in its cavity in the base.
Slide the snap downwards while keeping it in place.
Verify the snap is correctly installed: the middle part of the snap should be locked underneath the locking feature in the base as shown.