Nokta AccuPOINT Pinpoint Detector User Manual
- June 13, 2024
- Nokta
Table of Contents
DETECTION TECHNOLOGY
USER MANUAL
AccuPOINT Pinpoint Detector
WARNINGS
AccuPOINT is an electronic device manufactured with advanced technology. Do
not use your device without reading the user manual.
Do not leave the device in extremely cold or hot environments for long periods
of time. (Storage Temperature: -20°C to 50°C).
The device is designed to be waterproof to IP68 standards up to 3 meters.
However, you must pay attention to the warnings below:
- Do not wash or immerse in water without the back cover attached to the device!
- Make sure that the o-ring on the back cover is fully fitted and that the cover is fully tightened before using or washing the device under water.
- To prevent damage to the filter on the back cover, do not insert any sharp objects into the holes for cleaning purposes, etc. Do not clean it with pressurized water or compressed air. Cleaning it with tap water is sufficient. Be careful to prevent excessive dirt buildup and blockage.
- Make sure to replace the worn-out o-ring on the back cover with the spare one. Damaged o-ring may cause the device to leak.
Never use chemical cleaners during cleaning, especially after using the device
in salt water, or at any other time.
Protect the device from impacts during transportation.
AccuPOINT can only be opened and repaired by authorized service centers.
Opening the device for any reason will void the warranty.
INTRODUCTION TO TH E DEVICE
BATTERY & CHARGING INFORMATION
You can charge your AccuPOINT device with a USB charger that provides an
output between 0.8A/5V and 3A/6.6V.
The charging time is approximately 2.5-3 hours.
In order to charge the device, you need to remove the audio booster piece
after opening the back cover.
After charging is complete, do not forget to put this piece back in its place!
While AccuPOINT is charging, a lightning bolt symbol appears inside the
battery icon. When charging is complete, the battery icon displays 3 bars
indicating a full charge.
When the battery is almost depleted, the device emits intermittent beep sounds as a warning. When the battery is completely depleted, after emitting 2 beeps and a long beep it shuts down.
OPERATION OF THE DEVICE
Turning on the Device
Press and release the Power On/Off & Settings button once. After the beep
sound,
AccuPOINT will be ready for use. AccuPOINT automatically resets itself when
turned on. Therefore, make sure to keep the device away from metals when
turning it on.
Turning off the Device
To turn off AccuPOINT, press and hold the Power .
On/Off & Settings button for approximately 2 seconds and release the button
once the indicator bar at the bottom hits the red part.
AccuPOINT will shut down after 2 beeps. When the device is turned off and then
back on, it will start in the last set configuration.
Reset
If you plan to use AccuPOINT on wet beach sand or highly mineralized
terrain, it is recommended to either turn on the device with the search tip
placed on the ground you intend to use it on or reset it on the same ground.
This may cause some loss of depth but ensures stable operation of the device.
You can also reset the device if it receives erroneous signals during use. To
do this, press the Power On/Off & Settings button once while the device is on.
Do not perform the reset on metal, as it may result in some loss of depth.
Metal Detection
The device provides audible and/or vibrating alerts when it detects metal. The
frequency of sound or vibrations increases as the device gets closer to the
metal and decreases as it moves away. If the target is directly under the
search coil, it produces a steady sound.
SETTINGS
To access the settings, press and hold the Power On/Off & Settings button while the device is on and wait until the indicator reaches the settings icon. Release the button when you hover over the settings icon and hear 1 beep.
The
first setting that will appear on the screen is the sensitivity. Each time you
press the button, you move to the next setting. If you want to access a
setting and change its value, you need to press and hold the button for about
2 seconds.
While
in any of the settings, the device will revert back to the settings menu 2
seconds after you adjust the setting or 5 seconds after if you didn’t adjust
the setting. To return to the main screen from the settings menu, wait for 5
seconds without pressing the button.
Sensitivity
The sensitivity level consists of nine (9) steps. The device starts at the
factory default level of seven (7). To increase sensitivity, press the Power
On/Off & Settings button once. Each press will increase the sensitivity value
by one step. The sensitivity level is displayed both as a number and a
graphic. Sound and Vibration
While using AccuPOINT, you can choose to enable only sound, only vibration, or
both sound and vibration simultaneously. Use the Power On/Off & Settings
button to view and enable/disable sound and vibration symbols on the LCD
screen separately or together.
NOTE: When the device is in vibration mode, the option to hear the audio
from the speaker in the Bluetooth setting cannot be selected. Similarly, when
both headphones and speaker sound are selected in the Bluetooth setting,
vibration feature cannot be used.
Modes and Discrimination
AccuPOINT has 3 different search modes:
v1-Tone: In this mode, the device does not discriminate between metals and
produces the same sound alert for all metals.
Iron Off: Provides alerts only for non-ferrous metals and not for ferrous
metals. This mode is especially recommended for use on wet beach sand or
highly mineralized terrains.
2-Tone: In this mode, the device discriminates between iron and non-ferrous
metals.
When AccuPOINT detects metal for the first time, it produces the same sound
alert for all metals regardless of whether the metal is iron or non-ferrous.
As you get closer to the metal or when the device begins to discriminate, it
continues to produce the same tone if the metal is non-ferrous. If the metal
is ferrous though, it starts producing an interrupted alert. If vibration is
enabled, the vibration pattern matches the sound pattern. You can switch
between modes and control your settings from the LCD screen using the Power
On/Off & Settings button.
Bluetooth®
After turning on your Bluetooth®-enabled headphones, go to the Bluetooth®
setting and activate the wireless headphones icon with the Power On/Off &
Settings button. AccuPOINT will automatically detect and connect to your
headphones. This process may take more than a few minutes for the initial
pairing!
IMPORTANT! Before pairing your Bluetooth® headphones with AccuPOINT, if
there is another device already paired with the headphones, make sure that the
Bluetooth® feature of that device and/or the device itself is turned off.
Otherwise the headphones will not pair with AccuPOINT.
In the Bluetooth® setting, you can configure to hear the audio through the
Bluetooth® headphones only or both through the Bluetooth® headphones and
speaker simultaneously. AccuPOINT will automatically detect and connect to
your headphones every time it is powered on.
IMPORTANT! It may take 10-15 seconds for the audio to switch from
AccuPOINT to the detector once you turn the AccuPOINT off.
Once the AccuPOINT is paired with your headphones, if you want to pair it with
a different set of headphones this process may take more than a few minutes.
Frequency Shift
This setting is used to prevent interference with other detectors operating
nearby. AccuPOINT has 3 different frequency shifts. To change the frequency
value, press the Power On/Off & Settings button sequentially.
LED Flashlight
It is the headlight used for lighting the area you are scanning while
detecting at night or in dark locations. The LED Flashlight does not work when
the device is off. It is recommended to turn it on when needed as keeping it
on all the time can reduce battery life. To turn on the LED flashlight, you
can set it on the LCD screen by pressing the On/Off and Settings buttons
alternately.
Volume
AccuPOINT has two different volume levels: Low and High. You can adjust the
volume level by pressing the Power On/Off & Settings button and monitoring it
on the LCD screen.
Backlight
AccuPOINT has two different backlight levels: Bright and Low. You can adjust
the backlight by pressing the Power On/Off & Settings button. AccuPOINT will
automatically turn off the backlight if the button is not pressed for 20
seconds. When the Power On/Off & Settings button is pressed again, the
backlight will be activated. NOTE: The backlight level will remain the same
during charging.
Factory Defaults
AccuPOINT saves all the changes you make in its memory. If you want to restore
the device to factory defaults, go to settings, select the ‘Factory Defaults’
icon, and press and hold the Power On/Off & Settings button for 2 seconds
(until the hourglass icon appears). It will return to the main screen after
approximately 5 seconds.
Lost Alarm
AccuPOINT has an alarm feature for loss prevention. If the device is not used
and the button is not pressed for five (5) minutes, the device will provide an
audible alert and the LED Flashlight will start flashing. The device will
continue to provide the sound alert until the button is pressed or the battery
dies.
Detection Tip
AccuPOINT’s detection area extends from the tip to the hand grip and provides
360° detection. This allows you to easily locate metals inside dug holes and
quickly scan a wider area to find your target.
Battery Indicator
You can check your device’s battery status monitoring the battery icon on the
LCD screen.
Replaceable Tip Protector
AccuPOINT comes with two replaceable tip protectors.
TECHNICAL SPECIFICATIONS
Operating Frequency: 20kHz
Operating Principle: VLF
Waterproofness: IP68 (up to 3 m./10 ft)
Sensitivity: 9 levels adjustable
Metal Detection: Audio, Vibration and Audio&Vibration Alert
Discrimination: Yes
Bluetooth: Yes
Frequency Shift: Yes
LED Flashlight: Yes
Volume Control: Yes
Backlight: Yes
Screen: Color LCD
Lost Alarm: Yes
Detection Tip: 9 cm. ( 3.5’’)
Battery: 1650mAh Lithium Polymer
rechargeable
Charging Cable: USB Type-C
Battery Life: Up to 25 hours
Dimensions: 24,7cmx3,8cmx3,8cm (9.7’’x1.5’’x1.5’’)
Weight: 217gr (7,65oz)
Working Temperature: -20°C/+50°C (-4°F/+122°F)
Warranty: 2 years
Nokta Detectors reserves the right to change the design, specifications
or accessories without notice and without any obligation or liability
whatsoever.
**** For Consumers within the European Union: Do not dispose of this equipment in general household waste. The crossed wheeled bin symbol on this equipment indicates this unit should not be disposed of in general household waste, but recycled in compliance with local government regulations andb environmental requirements.
FCC STATEMENT
This
device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>