MORRIS MSU-8551 Stacking Kit Instruction Manual

: September 28, 2024
: MORRIS

Table of Contents

MORRIS MSU-8551 Stacking Kit
Specifications
FAQs
PRODUCT INFORMATION
Accessories
Installing steps
CONTACT INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MORRIS MSU-8551 Stacking Kit

Specifications

Product Name: MORRIS MSU-8551 Stacking Kit
Compatibility: Suitable for installing drum washing machines with box depth L 440mm/510mm/540mm
Features: Front adjusting feet, rear fixing blocks, top panel fixing block, anchor nut adjustment

FAQs

Q: Is the stacking kit compatible with all drum washing machines?

A: The stacking kit is suitable for installing drum washing machines with specific box depths as mentioned in the specifications.

Q: How many positioning holes need to be drilled for securing the stacking kit?

A: Six positioning holes need to be drilled on the top panel of the washer to secure the stacking kit.

PRODUCT INFORMATION

ATTENTION:

Two service personnel or more are needed when installing the dryer on the washing machine.
Safety accidents may be caused if installing a manual is not followed.
The stacking kit should be installed when the power is off.
Please do not stack the washing machine on the dryer.
The tilted angle of the machine should be less than 30°when installing.
The stacking kit is suitable for placing clothes and the maximum weight should be less than 16 kg. Children are prohibited from climbing.
The stacking kit is suitable for both new (See Annex 1 and Figure 1, with vertical stripes) and old(See Annex 2 and Figure 2, with horizontal stripes) platforms, the main difference:
- There are only two front adjusting feet on the new platform, and the rear part needs to be fixed with two rear fixing blocks;
- There are four adjusting feet on the new platform, and the two rear fixed blocks are not needed.
The stacking kit is suitable for installing a drum washing machine with box depth L 440mm/510mm/540mm. It is available for the current old platform and new platform models.

Accessories

A- Stacking kit（1）
B- Screw M6（1）
C- Screw C（2）
D – Screw M6 (6)
E- Gasket(1)
F-fixing pad(2)
G1-Rear fixing block（Right,1）
- G2- Rear fixing block（Left,1）
H1- Front fixing block（Right,1）
- H2- Front fixing block（Left,1）
I- Top panel fixing block（1）

Installing steps

First, ensure the installation of the washing machine is completed according to the installation manual of the drum washing machine, and adjust the balance of the washing machine.
Second, ensure the accessories are complete.
Third, place the stacking kit on the top panel of the drum washer with the handle of the stacking kit on the same side as the control panel of the drum washer. As shown below, align the stacking kit with the washer at the left and right positions.
Fourth , identify and drill 6 positioning holes of the stacking kit on the top panel of the washer, and fit 6 screws with broachΦ3 to fix the stacking kit to the top panel of the washer. Control the torque to be less than 10nm
Fifth , install top panel fixing block. Fix the jack catch of the block on the top panel of the washer. Align the mounting hole of the block with the mounting hole of the stacking kit, and fix the block with B-screw M6 and E- E-E-Gasket.
Sixth , adjust the anchor nut of the dryer. The new platform needs to be adjusted around only 2 front anchor nuts, screwed out 12 mm; the old platform needs to be adjusted around 4 anchor nuts, screwed out 16mm for 2 anchors nut in the front, and screwed out 14mm for 2 anchors nut at the back.
Seventh, put the dryer. Pull the drawer handle first, and place the adjusted dryer in the frame of the stacking kit. Note that the front foot is placed on the outside of the card slot first, then push the dryer backward, so that the foot of the dryer slips into the slot.
Eighth , then put two front fixing blocks into the slot of the stacking kit respectively, notice the distinction between left and right block.
Ninth , remove the 2 screws at the lower side of the side panel after the dryer. Place two rear fixing blocks into the slot of the stacking kit, notice the distinction between left and right block. Then fix two rear fixing blocks with 2 screws removed before.
- Note : the old platform dryer does not need to do this step!
Tenth , check if there is a loose phenomenon, and if the handle is normal to pull out, check whether there is interference. If it is OK, installation is complete.