B76900101 Concrete Chute Bucket

“`html

Concrete Chute Bucket

Specifications

• Model: Concrete Chute Bucket
• Serial Number: B76900101 & Above
• Manufactured: May 2024
• Origin: USA

Product Information

Features and Accessories

The Concrete Chute Bucket comes with the following standard
items:

• Chute Extension
• Machine Quick Coupler

Product Usage Instructions

Initial Setup

To set up the Concrete Chute Bucket, follow these steps:

1. Attach the Chute Extension securely.

Daily Inspection

Perform daily inspections by following these steps:

1. Inspect the Concrete Chute Bucket for any damages or wear.
2. Check the Machine Quick Coupler for proper functioning.

Preventive Maintenance

To ensure the longevity of your Concrete Chute Bucket, perform
preventive maintenance regularly.

Frequently Asked Questions (FAQ)

Q: How often should I inspect the Concrete Chute Bucket?

A: Daily inspections are recommended to ensure safe and
efficient operation.

Q: Can I use the Concrete Chute Bucket without the Chute

Extension?

A: It is not recommended to use the Concrete Chute Bucket
without the Chute Extension for safety and operational reasons.

Q: What should I do if I encounter issues with the Machine

Quick Coupler?

A: Refer to the Troubleshooting Chart in the manual or contact
customer support for assistance.

“`

Operation & Maintenance Manual
Concrete Chute Bucket
Concrete Chute Bucket S/N: B76900101 & Above

46904694enUS (A) May 2024

Printed in USA Original Instructions

© 2024 Ignite Attachments. All Rights Reserved.

TABLE OF CONTENTS
FOREWORD………………………………………………………………………………………………………………………………………… 3
MANUFACTURER…………………………………………………………………………………………………………………………… 3 North America …………………………………………………………………………………………………………………………….. 3
SERIAL NUMBER LOCATION …………………………………………………………………………………………………………… 3 Attachment Serial Number ………………………………………………………………………………………………………………. 3
ATTACHMENT IDENTIFICATION ……………………………………………………………………………………………………….. 4 Concrete Chute Bucket ………………………………………………………………………………………………………………….. 4
FEATURES AND ACCESSORIES ………………………………………………………………………………………………………. 4 Standard Items ……………………………………………………………………………………………………………………………. 4
SAFETY AND TRAINING RESOURCES…………………………………………………………………………………………………….. 5
SAFETY INSTRUCTIONS …………………………………………………………………………………………………………………. 5 Safe Operation Is The Operator’s Responsibility ……………………………………………………………………………………… 5 Safe Operation Needs A Qualified Operator…………………………………………………………………………………………… 5 Use Safety Rules …………………………………………………………………………………………………………………………. 5 Call Before You Dig ………………………………………………………………………………………………………………………. 5 Silica Dust Exposure……………………………………………………………………………………………………………………… 6
FIRE PREVENTION…………………………………………………………………………………………………………………………. 6 Maintenance ………………………………………………………………………………………………………………………………. 6 Operation ………………………………………………………………………………………………………………………………….. 6 Electrical …………………………………………………………………………………………………………………………………… 6 Hydraulic System …………………………………………………………………………………………………………………………. 6 Fueling …………………………………………………………………………………………………………………………………….. 7 Starting…………………………………………………………………………………………………………………………………….. 7 Spark Arrester Exhaust System…………………………………………………………………………………………………………. 7 Welding And Grinding ……………………………………………………………………………………………………………………. 7 Fire Extinguishers ………………………………………………………………………………………………………………………… 7
PUBLICATIONS AND TRAINING RESOURCES ……………………………………………………………………………………. 8
OPERATING INSTRUCTIONS …………………………………………………………………………………………………………………. 9
INITIAL SETUP ………………………………………………………………………………………………………………………………. 9 Attaching The Chute Extension …………………………………………………………………………………………………………. 9
DAILY INSPECTION ………………………………………………………………………………………………………………………… 9 Inspecting The Concrete Chute Bucket ………………………………………………………………………………………………… 9 Inspecting The Machine Quick Coupler………………………………………………………………………………………………… 9
OPERATING PROCEDURE …………………………………………………………………………………………………………….. 11 Approved Models And Requirements ………………………………………………………………………………………………… 11 Entering And Exiting The Machine ……………………………………………………………………………………………………. 11 Installing The Attachment ……………………………………………………………………………………………………………… 11 Operating The Controls ………………………………………………………………………………………………………………… 15 Operating The Concrete Chute Bucket ………………………………………………………………………………………………. 15 Removing The Attachment…………………………………………………………………………………………………………….. 17 Lifting The Attachment …………………………………………………………………………………………………………………. 18 Transporting The Attachment On A Trailer …………………………………………………………………………………………… 19
PREVENTIVE MAINTENANCE ………………………………………………………………………………………………………………. 20
TROUBLESHOOTING ……………………………………………………………………………………………………………………. 20 Troubleshooting Chart………………………………………………………………………………………………………………….. 20
REMOVING THE CHUTE EXTENSION………………………………………………………………………………………………. 20 ATTACHMENT STORAGE AND RETURN TO SERVICE ……………………………………………………………………….. 21
1

TABLE OF CONTENTS Attachment Storage…………………………………………………………………………………………………………………….. 21 Return To Service ………………………………………………………………………………………………………………………. 21
SPECIFICATIONS……………………………………………………………………………………………………………………………….. 22 CONCRETE BUCKET DIMENSIONS ………………………………………………………………………………………………… 22
TORQUE SPECIFICATION FOR BOLTS ………………………………………………………………………………………………….. 23 TORQUE FOR GENERAL SAE BOLTS ……………………………………………………………………………………………… 23 TORQUE FOR GENERAL METRIC BOLTS ………………………………………………………………………………………… 24
WARRANTY ………………………………………………………………………………………………………………………………………. 25 ATTACHMENT / IMPLEMENT WARRANTY………………………………………………………………………………………… 25
2

MANUFACTURER North America
Ignite Attachments 2741 20th Avenue South Moorhead, MN 56560 1­888­232­1988

SERIAL NUMBER LOCATION Attachment Serial Number
Figure 1

FOREWORD

C227559b
Always use the serial number (Item 1) of the concrete bucket (Item 2) [Figure 1] when requesting service information or when ordering parts. Earlier or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

3

ATTACHMENT IDENTIFICATION Concrete Chute Bucket
Figure 2

FOREWORD
FEATURES AND ACCESSORIES Standard Items
The attachment is equipped with the following standard items: · Spill Guard · Removable Chute Extension · Fill Level Gauge · Steps

C227558c
REF. 1 2 3 4

Description Steps Removable Chute Extension Fill Gauge Spill Guard

4

SAFETY INSTRUCTIONS Safe Operation Is The Operator’s Responsibility
Safety Alert Symbol
This symbol with a warning statement means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.
DANGER
The signal word DANGER on safety signs and in the manuals indicates a hazardous situation which, if not avoided, will result in serious injury or death.
D-1002
WARNING
The signal word WARNING on the safety signs and in the manuals indicates a potentially hazardous situation which, if not avoided, could result in serious injury or death.
W-2044
IMPORTANT
This notice identifies procedures which must be followed to avoid damage to the machine.
I-2019
The machine and attachment must be in good operating condition before use.
Safe Operation Needs A Qualified Operator
For an operator to be qualified, he or she must not use drugs or alcoholic drinks which impair alertness or coordination while working. An operator who is taking prescription drugs must get medical advice to determine if he or she can safely operate a machine.
Use Safety Rules
· Read and follow instructions in the machine and the attachment’s Operation & Maintenance Manual before operating.
· Check for underground lines before operating attachment (if applicable).
· In addition to the design and configuration of equipment, hazard control, and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment.
· Check that the attachment is securely fastened to the machine.

SAFETY AND TRAINING RESOURCES
· Make sure all the machine controls are in the neutral position before starting the machine.
· Operate the attachment only from the operator’s position.
· Operate the attachment according to the Operation & Maintenance Manual.
· When learning to operate the attachment, do it at a slow rate in an area clear of bystanders.
· DO NOT permit personnel to be in the work area when operating the machine and attachment.
· The attachment must be used ONLY on approved machines. Visit igniteattachments.com for an updated list of approved attachments for each machine model.
· DO NOT modify equipment or add attachments that are not approved by the manufacturer.
· DO NOT make any adjustments or repairs on the machine or attachment while the engine is running.
· Keep shields and guards in place. Replace if damaged.
Call Before You Dig
P200081
Dial 811 (USA Only) Dial 1-888-258-0808 (USA & Canada) When you call, you will be directed to a location in your state / province / city for information about buried lines (telephone, cable TV, water, sewer, gas, etc.).

5

Silica Dust Exposure

SAFETY AND TRAINING RESOURCES
FIRE PREVENTION

NA3504
Silica dust can cause lung disease and is known to the state of California to cause cancer. Cutting or drilling concrete containing sand or rock containing quartz may result in exposure to silica dust. Do not exceed Permissible Exposure Limits (PEL) to silica dust as determined by OSHA or other job site Rules and Regulations. Use a respirator, water spray, or other means to control dust.

NA3505
Maintenance
The machine, some attachments, and some implements have components that are at high temperatures under normal operating conditions. The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a source of arcs or sparks. Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it can cause a fire hazard. Clean often to avoid this accumulation. Flammable debris in the engine compartment is a potential fire hazard. The operator’s area, engine compartment, and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazards and overheating. All fuels, most lubricants, and some coolant mixtures are flammable. Flammable fluids that are leaking or spilled onto hot surfaces or onto electrical components can cause a fire.
Operation
Do not use the machine where exhaust, arcs, sparks, or hot components can contact flammable material, explosive dust, or gases.
Electrical

P200082
Check all electrical wiring and connections for damage. Keep the battery terminals clean and tight. Repair or replace any damaged part or wires that are loose or frayed. Battery gas can explode and cause serious injury. Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting. Do not jump start or charge a frozen or damaged battery. Keep any open flames or sparks away from batteries. Do not smoke in battery charging area.
Hydraulic System
Check hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for
6

leaks. Hydraulic tubes and hoses must be properly routed and have adequate support and secure clamps. Tighten or replace any parts that show leakage. Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.
Fueling

SAFETY AND TRAINING RESOURCES
Dust generated from repairing nonmetallic parts such as hoods, fenders, or covers can be flammable or explosive. Repair such components in a well- ventilated area away from open flames or sparks.
Fire Extinguishers

P200084
Stop the engine and let it cool before adding fuel. No smoking! Do not refuel a machine near open flames or sparks. Fill the fuel tank outdoors. Ultra Low Sulfur Diesel (ULSD) poses a greater static ignition hazard than earlier diesel formulations with higher sulfur content. Avoid death or serious injury from fire or explosion. Consult with your fuel or fuel system supplier to ensure the delivery system is in compliance with fueling standards for proper grounding and bonding practices.
Starting
Do not use ether or starting fluids on any engine that has glow plugs or an air intake heater. These starting aids can cause explosion and injure you or bystanders. Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting.
Spark Arrester Exhaust System
The spark arrester exhaust system is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the exhaust gases are still hot. Check the spark arrester exhaust system regularly to make sure it is maintained and working properly. Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrester muffler (if equipped).
Welding And Grinding
Always clean the machine and attachment, disconnect the battery, and disconnect the wiring from the Ignite Attachments controllers before welding. Cover rubber hoses, battery, and all other flammable parts. Keep a fire extinguisher near the machine when welding. Have good ventilation when grinding or welding painted parts. Wear a dust mask when grinding painted parts. Toxic dust or gas can be produced.

P200083
Know where fire extinguishers and first aid kits are located and how to use them. Inspect the fire extinguisher and service the fire extinguisher regularly. Obey the recommendations on the instructions plate.

7

PUBLICATIONS AND TRAINING RESOURCES
The following publications are also available for your Ignite Attachments product. Access them online at Igniteattachments.com.
Operation & Maintenance Manual Complete instructions on the correct operation and the routine maintenance of your Ignite Attachments product. 46904694
C227195a
For the latest information on Ignite Attachments products and the Ignite Attachments Company, visit our website at Igniteattachments.com

SAFETY AND TRAINING RESOURCES

8

INITIAL SETUP Attaching The Chute Extension
Figure 3

OPERATING INSTRUCTIONS
DAILY INSPECTION Inspecting The Concrete Chute Bucket
Figure 5

C227558d
1. Set the chute extension (Item 1) onto the concrete bucket (Item 2) [Figure 3] and align the holes.
Figure 4
C227558e
2. Use the four bolts and nuts (Item 1) [Figure 4] to install the chute extension to the concrete bucket.
3. Torque the hardware to the specified values.

C227559d
Inspect the concrete chute bucket wedge mounts (Item 1), mounting flanges (Item 2) [Figure 5], and all welds on the attachment for wear and damage each time the attachment is removed from the machine. Frequently inspect the attachment to ensure that all components are secure and that all bolts and nuts are thoroughly tightened.
Inspecting The Machine Quick Coupler
WARNING
CRUSHING HAZARD Failure to secure attachment coupler wedges can allow attachment to come off and cause serious injury or death. Both wedges must extend through the holes in the attachment mounting frame. Levers must be fully down and locked.
W-2715-EF

9

Figure 6

Figure 8

OPERATING INSTRUCTIONS

NA3448a
· Push the quick coupler levers down until they are fully engaged in the locked position [Figure 6] (wedges fully extended through the holes in the attachment). The levers and wedges must move freely [Figure 6].
Figure 7

NA3450A
The wedges must extend through the holes in the attachment mounting frame, securely fastening the attachment to the machine quick coupler [Figure 7]. If the wedge does not contact the lower edge of the hole, the attachment will be loose and can come off the quick coupler.

NA13065S
· Inspect the attachment bucket. · Replace any parts that are damaged, bent, or
missing [Figure 8]. · Keep all fasteners tight. · Look for cracked welds. · Contact your Ignite Attachments representative for
replacement parts. · Lubricate the wedges. (See the machine’s Operation
& Maintenance Manual for the correct procedure.)

10

OPERATING PROCEDURE Approved Models And Requirements

Concrete Chute Bucket

Minimum ROC of Carrier 681 kg (1500 lb)

The chart shows the minimum Rated Operating Capacity (ROC) required for operation of the concrete chute bucket. To prevent potential overloading issues, compare the machine’s rated operating capacity to the weight of the attachment, plus the estimated weight of the load. Never attempt to lift more than the rated operating capacity of the loader (attachment weight and load). See the Specification section for the weight of your attachment. (See Specifications on Page 22)

Fill Gauge Level
1/4 yard 1/2 yard 2/3 yard

Weight of concrete based on density of 2405 kg/ m3 (4050 lbs/cu. yd)

Weight of Concrete
Chute Bucket

459 kg (1013 lbs)

919 kg 179 kg (394

(2025 lbs)

lbs)

1226 kg (2701 lbs)

Total Weight (Bucket and Load)
638 kg (1407 lbs) 1098 kg (2419 lbs) 1405 kg (3095 lbs)

WARNING
INSTABILITY HAZARD Excessive load can cause loss of control or tipping leading to serious injury or death. DO NOT exceed Rated Operating Capacity (ROC).
W-2053
Warranty on this attachment is void if used on a nonapproved carrier. Contact your Ignite Attachments representative for a current list of approved carriers.
WARNING
MODIFICATION AND INSUFFICIENT INSTRUCTION HAZARD Use of unapproved attachments or improperly sized attachments can cause serious injury or death. Attachments and buckets for safe loads of specified densities are approved for each model. Never use attachments or buckets which are not approved by Ignite Attachments.
W-2662

OPERATING INSTRUCTIONS
Entering And Exiting The Machine WARNING
GENERAL HAZARD Failure to obey warnings can cause serious injury or death. Obey all warnings on the machine and in the manuals.
W-2744
Figure 9
C216077a
Use the attachment / implement steps (if equipped), grab handles, and safety treads (on the machine and frame) to get in and out of the machine, maintaining a three-point contact at all times [Figure 9]. Do not jump. See the machine’s Operation & Maintenance Manual for detailed instructions on entering and exiting the machine.
Installing The Attachment
Installing With Non-powered Machine Quick Coupler The illustrations and instructions provided explain how to install a bucket attachment onto a machine. Follow these same instructions if you are installing different attachments such as a grapple, snow pusher, sweeper, etc. The attachment mounting frame for the attachment has a top flange that is designed to receive the top edge of the machine quick coupler and the lower part of the frame is designed to receive the quick coupler wedges.

11

WARNING
GENERAL HAZARD Failure to obey warnings can cause serious injury or death. Obey all warnings on the machine and in the manuals.
W-2744
Always inspect the machine’s quick coupler and the attachment mounting frame before installation. (See the machine’s Operation & Maintenance Manual.) Figure 10

Figure 11

OPERATING INSTRUCTIONS

NA3446a
6. Drive the machine slowly forward until the top edge of the quick coupler is completely under the top flange of the attachment [Figure 11]. NOTE: Be sure the quick coupler levers do not hit the attachment.
Figure 12
NA3445A
1. Pull the quick coupler levers up until they are fully raised (wedges fully raised) [Figure 10].
2. Enter the machine. 3. Turn the machine on. 4. Release the parking brake. 5. Lower the lift arms and tilt the machine quick coupler
forward.
NA3447a
7. Tilt the quick coupler backward until the attachment is slightly off the ground [Figure 12]. This will cause the attachment mounting frame to fit up against the front of the quick coupler. NOTE: When leaving the operator’s seat to install an attachment, tilt the attachment until it is slightly off the ground.
8. Turn the machine off and exit the machine.
12

OPERATING INSTRUCTIONS

WARNING
GENERAL HAZARD Failure to follow instructions can cause serious injury or death. Before you leave the operator’s seat: · Lower the lift arms and put the attachment flat
on the ground. · Engage the parking brake. · Move all controls to the NEUTRAL / LOCKED
position to make sure the lift, tilt, and drive functions are deactivated. · Stop the engine.
W-3156
Figure 13

WARNING
CRUSHING HAZARD Failure to secure attachment coupler wedges can allow attachment to come off and cause serious injury or death. Both wedges must extend through the holes in the attachment mounting frame. Levers must be fully down and locked.
W-2715-EF
Figure 14

NA3448A
9. Push down on the quick coupler levers until they are fully engaged in the locked position [Figure 13] (wedges are fully extended through the attachment mounting frame holes). If both levers do not engage in the locked position, see your machine dealer or representative for maintenance.

NA3450A
The wedges must extend through the holes in the attachment mounting frame, securely fastening the attachment to the quick coupler [Figure 14]. Installing With Powered Machine Quick Coupler
WARNING
GENERAL HAZARD Failure to obey warnings can cause serious injury or death. Obey all warnings on the machine and in the manuals.
W-2744
Some machines may be equipped with a powered machine quick coupler. For specific control location and operation of the machine’s powered quick coupler, see the machine’s Operation & Maintenance Manual. 1. Enter the machine. 2. Turn the machine on. 3. Release the parking brake.

13

Figure 15

Figure 17

OPERATING INSTRUCTIONS

NA3453A
4. Operate the powered quick coupler until the levers are fully raised (wedges fully raised) [Figure 15].
5. Lower the lift arms and tilt the machine quick coupler slightly forward.
Figure 16

NA3447a
7. Tilt the quick coupler backward until the attachment is slightly off the ground [Figure 17]. This will cause the attachment mounting frame to fit up against the front of the quick coupler. Some powered quick coupler system have continuous pressurized hydraulic oil to keep the wedges in the engaged position and prevent attachment disengagement. Because the wedges can slowly lower, the operator may need to reactivate the powered quick coupler to be sure both wedges are fully raised before installing the attachment.
8. Operate the powered quick coupler until the levers are fully raised (wedges fully raised).
Figure 18

NA3446a
6. Drive the machine slowly forward until the top edge of the quick coupler is completely under the top flange of the attachment mounting frame [Figure 16]. NOTE: Be sure the quick coupler levers do not hit the attachment.
NA3454A
14

9. Operate the powered quick coupler until the levers are fully engaged in the locked position [Figure 18] (wedges fully extended through the attachment mounting frame holes). If both levers do not engage in the locked position, see your machine dealer or representative for maintenance.
WARNING
CRUSHING HAZARD Failure to secure attachment coupler wedges can allow attachment to come off and cause serious injury or death. Both wedges must extend through the holes in the attachment mounting frame. Levers must be fully down and locked.
W-2715-EF
Figure 19
NA3450A
10. The wedges must extend through the holes [Figure 19] in the attachment mounting frame, securely fastening the attachment to the quick coupler.
11. Lower the lift arms and put the attachment flat on the ground.
12. Turn the machine off and exit the machine.

OPERATING INSTRUCTIONS
WARNING
GENERAL HAZARD Failure to follow instructions can cause serious injury or death. Before you leave the operator’s seat: · Lower the lift arms and put the attachment flat
on the ground. · Engage the parking brake. · Move all controls to the NEUTRAL / LOCKED
position to make sure the lift, tilt, and drive functions are deactivated. · Stop the engine.
W-3156
Operating The Controls
1. Enter the machine. 2. Fasten the seat belt and lower the seat bar (if
applicable). 3. Start the engine. 4. The lift and tilt functions of the machine will be used
to operate the concrete bucket (See the machine’s operation & maintenance manual for correct procedure).
Operating The Concrete Chute Bucket
Operating On Slopes With A Full Attachment NOTE: The illustrations and instructions provided explain
how to operate a machine with a generic attachment. Follow these same instructions for all load-carrying attachments.
WARNING
GENERAL HAZARD Contact with equipment can cause serious injury or death. Keep all bystanders 6 m (20 ft) away from equipment when operating.
W-2268
WARNING
GENERAL HAZARD Failure to follow instructions can cause serious injury or death. When operating the machine: · Keep the seat belt fastened snugly. · The seat bar must be lowered. · Keep your feet on the pedal controls or footrests
and hands on the controls.
W-2261

15

Figure 20

OPERATING INSTRUCTIONS
Operating On Slopes With An Empty Attachment Figure 22

NA15864
Figure 21

NA15866A
Figure 23

NA15865
· With a full attachment, drive up or down the slope with the heavy end toward the top of the slope [Figure 20] and [Figure 21].

NA15867A
· With an empty attachment, drive up or down the slope with the heavy end toward the top of the slope [Figure 22] and [Figure 23].
Loading The Concrete Bucket 1. Lower the lift arms and place the concrete bucket on
level ground.

16

Figure 24
C228375a
2. Fill the concrete bucket with concrete to the desired level. The fill gauge is incremented in ¼ (Item 1), ½ (Item 2), and (Item 3) [Figure 24] cubic yards. Do not fill the concrete bucket with more material than your machine can lift. See specifications page in this manual for attachment weight and see your machines operation & maintenance manual for rated operating capacity.
WARNING
INSTABILITY HAZARD Machine tipping or rollover can cause serious injury or death. Load, unload and turn on flat level ground. DO NOT exceed ROC.
W-3199
3. Drive slowly to the location where the concrete will be unloaded.
4. Raise the lift arms and slowly tilt the concrete bucket out until concrete flows from the chute.
5. Continue tilting the concrete bucket until it is empty.
Removing The Attachment
Removing With Non-powered Machine Quick Coupler 1. Lower the lift arms and put the attachment flat on the
ground. NOTE: In muddy conditions or to prevent the
attachment from freezing to the ground, put the attachment on planks or blocks before removing the attachment from the machine. 2. Turn the machine off and release auxiliary hydraulic pressure (if applicable). (See the machine’s

OPERATING INSTRUCTIONS
Operation & Maintenance Manual for correct procedure.)
WARNING
GENERAL HAZARD Failure to follow instructions can cause serious injury or death. Before you leave the operator’s seat: · Lower the lift arms and put the attachment flat
on the ground. · Engage the parking brake. · Move all controls to the NEUTRAL / LOCKED
position to make sure the lift, tilt, and drive functions are deactivated. · Stop the engine.
W-3156
3. Exit the machine and disconnect auxiliary hydraulic hoses (if applicable).
4. Disconnect electrical connections (if applicable). Figure 25
NA3445A
5. Pull the machine quick coupler levers up [Figure 25] until they are fully raised (wedges fully up).
WARNING
PINCHING HAZARD Failure to follow instructions can cause serious injury. Keep fingers and hands out of pinch points when latching and unlatching the attachment quick coupler.
W-2541
6. Enter the machine. 7. Turn the machine on. 8. Release the parking brake.

17

Figure 26

OPERATING INSTRUCTIONS
2. Operate the powered quick coupler until the levers are fully raised (wedges fully raised) [Figure 27].
Figure 28

NA3447b
9. Tilt the quick coupler forward and drive the machine backward, away from the attachment [Figure 26].
Removing With Powered Machine Quick Coupler For specific control location and operation of the machine’s powered quick coupler, see the machine’s Operation & Maintenance Manual. 1. Lower the lift arms and put the attachment flat on the
ground. Lower or close the hydraulic equipment (if equipped). NOTE: In muddy conditions or to prevent the
attachment from freezing to the ground, put the attachment on planks or blocks before removing the attachment from the machine. Figure 27

NA3447b
3. Tilt the quick coupler forward and drive the machine backward, away from the attachment [Figure 28]. Some powered quick couplers have continuous pressurized hydraulic oil to keep the wedges in the engaged position and prevent attachment disengagement. Because the wedges can slowly lower, the operator may need to reactivate the powered quick coupler when removing an attachment to be sure both wedges are fully raised.
Lifting The Attachment
NOTE: Use straps or chains that are in good condition and of adequate capacity to lift the attachment.
Figure 29

NA3453A

C228376
18

· Fasten straps or chains to the steps on the side of the frame [Figure 29].
Transporting The Attachment On A Trailer
Fastening The Attachment On A Trailer Figure 30

OPERATING INSTRUCTIONS

C228377
Figure 31

C228378
1. Put the concrete chute bucket on the transport vehicle and fasten chains to both ends of the concrete bucket.
2. Secure the chains to the transport vehicle. 3. Use chain binders to prevent the concrete chute
bucket from moving during transport.
19

TROUBLESHOOTING Troubleshooting Chart

WARNING
INSUFFICIENT INSTRUCTIONS HAZARD Untrained operators or failure to follow instructions can cause serious injury or death. · Read and understand the Operation &
Maintenance Manual and decals on machine. · Follow warnings and instructions in the manuals
when making repairs, adjustments or servicing. · Check for correct function after adjustments,
repairs or service.
W-2408
Use the following troubleshooting chart to locate and correct problems that most often occur with the attachment.

PROBLEM Concrete chute bucket does not mount properly on the machine quick coupler.

CAUSE Quick coupler wedges are not fully retracted during hook-up.

CORRECTION Retract quick coupler wedges before installing attachment.

Mud, dirt or stones are lodged between the quick coupler and the attachment mounting frame.

Remove debris between quick coupler and the attachment mounting frame.

PREVENTIVE MAINTENANCE
REMOVING THE CHUTE EXTENSION
Figure 32
C227558e
1. Remove the four bolts and nuts (Item 1) [Figure 32] and the chute extension from the concrete bucket.

20

ATTACHMENT STORAGE AND RETURN TO SERVICE Attachment Storage
Sometimes it may be necessary to store your Ignite Attachments for an extended period of time. Below is a list of items to perform before storage. · Thoroughly clean the attachment. · Inspect the attachment mounting frame upper flange,
lower mounts, and all welds on the attachment for wear and damage. · Check for loose hardware, missing guards, or damaged parts. · Replace worn or damaged parts. · Check for damaged or missing decals. Replace if necessary. · Place the attachment in a dry protected shelter. · Place the attachment flat on the ground. NOTE: In muddy conditions or to prevent the
attachment from freezing to the ground, put the attachment on planks or blocks before removing the attachment from the machine.
Return To Service
After the Ignite Attachments attachment has been in storage, it is necessary to follow a list of items to return the attachment to service. · Be sure all shields and guards are in place. · Install and operate attachment, check for correct
function. · Check for leaks. Repair as needed.

PREVENTIVE MAINTENANCE

21

SPECIFICATIONS
CONCRETE BUCKET DIMENSIONS
Where applicable, specifications conform to SAE and ISO standards and are subject to change without notice. Figure 33

C227884a
DESCRIPTION Overall Length Of Bucket (A) Overall Height Of Bucket (B) Overall Width Of Bucket (C) Bucket Weight

CONCRETE CHUTE BUCKET 1818 mm (71.6 in) 622 mm (24.5 in) 1422 mm (56 in) 179 kg (394 lb)

22

TORQUE SPECIFICATION FOR BOLTS

TORQUE FOR GENERAL SAE BOLTS
The following minimum and maximum torque values are for use on steel hardware coated with zinc phosphate & oil and zinc dichromate in general applications and where torque values are not otherwise specified. The same torque values apply to course or fine threads.

THREAD SIZE 1/4″ 5/16″ 3/8″ 7/16″ 1/2″ 9/16″ 5/8″ 3/4″ 7/8″ 1″ 1-1/8″ 1-1/4″ 1-3/8″ 1-1/2″

CAP SCREW BOLT AND NUT SAE GRADE 5
9 ­ 10 N·m (80 ­ 90 in-lb) 21 ­ 23 N·m (180 ­ 200 in-lb) 34 ­ 38 N·m (25 ­ 28 ft-lb) 54 ­ 61 N·m (40 ­ 45 ft-lb) 88 ­ 95 N·m (65 ­ 70 ft-lb) 125 ­ 135 N·m (90 ­ 100 ft-lb) 170 ­ 190 N·m (125 ­ 140 ft-lb) 300 ­ 330 N·m (220 ­ 245 ft- lb) 450 ­ 490 N·m (330 ­ 360 ft-lb) 645 ­ 710 N·m (475 ­ 525 ft-lb) 880 ­ 975 N·m (650 ­ 720 ft-lb) 1220 ­ 1360 N·m (900 ­ 1000 ft-lb) 1630 ­ 1830 N·m (1200 ­ 1350 ft-lb) 2040 ­ 2240 N·m (1500 ­ 1650 ft-lb)

CAP SCREW BOLT AND NUT SAE GRADE 8
13 ­ 14 N·m (110 ­ 120 in-lb)
24 ­ 27 N·m (215 ­ 240 in-lb)
48 ­ 54 N·m (35 ­ 40 ft-lb) 82 ­ 88 N·m (60 ­ 65 ft-lb) 125 ­ 135 N·m (90 ­ 100 ft-lb) 170 ­ 190 N·m (125 ­ 140 ft-lb) 240 ­ 260 N·m (175 ­ 190 ft-lb) 410 ­ 450 N·m (300 ­ 330 ft-lb) 645 ­ 710 N·m (475 ­ 525 ft-lb) 985 ­ 1085 N·m (725 ­ 800 ft-lb) 1425 ­ 1600 N·m (1050 ­ 1175 ft-lb) 2000 ­ 2200 N·m (1475 ­ 1625 ft-lb) 2720 ­ 2980 N·m (2000 ­ 2200 ft-lb) 3520 ­ 3870 N·m (2600 ­ 2850 ft-lb)

SOCKET HEAD CAP SCREW OR 12­POINT HEAD CAP SCREW 15 ­ 16 N·m (130 ­ 145 in-lb) 31 ­ 34 N·m (270 ­ 300 in-lb) 61 ­ 68 N·m (45 ­ 50 ft-lb) 95 ­ 102 N·m (70 ­ 75 ft-lb) 150 ­ 160 N·m (110 ­ 120 ft-lb) 205 ­ 225 N·m (150 ­ 165 ft-lb) 285 ­ 310 N·m (210 ­ 230 ft-lb) 490 ­ 540 N·m (360 ­ 400 ft-lb) 600 ­ 650 N·m (815 ­ 880 ft-lb) 1220 ­ 1360 N·m (900 ­ 1000 ft-lb) 1770 ­ 1970 N·m (1300 ­ 1450 ft-lb) 2510 ­ 2720 N·m (1850 ­ 2000 ft-lb) 3330 ­ 3660 N·m (2450 ­ 2700 ft-lb) 4270 ­ 4680 N·m (3150 ­ 3450 ft-lb)

NOTE: Use the torque value for the part having the lesser grade when a fastener and nut are used together but have a different grade.

23

TORQUE SPECIFICATION FOR BOLTS

TORQUE FOR GENERAL METRIC BOLTS
Torque values shown in table below apply to combinations of a fastener and nut having the same property class, and both being coated with zinc phosphate and oil or zinc dichromate. Use the torque value for the part having the lesser property class when a fastener and nut are used together but have a different property class.

THREAD NOM. DIA. M4 M5 M6 M7 M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M33 M36

8.8 2,5 ­ 3,5 N·m (2.0 ­ 2.5 ft-lb) 5,5 ­ 6,5 N·m (4.0 ­ 5.0 ft-lb) 9,5 ­ 10,5 N·m (7.0 ­ 7.5 ft-lb) 15 ­ 17 N·m (11.0 ­ 12.5 ft-lb) 24 ­ 26 N·m (18 ­ 19 ft- lb) 43 ­ 47 N·m (32 ­ 35 ft-lb) 75 ­ 85 N·m (55 ­ 60 ft-lb) 125 ­ 140 N·m (90 ­ 100 ft-lb) 190 ­ 210 N·m (140 ­ 155 ft-lb) 260 ­ 290 N·m (190 ­ 215 ft-lb) 370 ­ 410 N·m (275 ­ 300 ft-lb) 500 ­ 550 N·m (370 ­ 400 ft-lb) 640 ­ 700 N·m (470 ­ 520 ft-lb) 930 ­ 1030 N·m (680 ­ 760 ft-lb) 1260 ­ 1400 N·m (930 ­ 1030 ft-lb) 1720 ­ 1900 N·m (1270 ­ 1400 ft-lb) 2200 ­ 2450 N·m (1620 ­ 1800 ft-lb)

PROPERTY CLASS 10.9
3,8 ­ 4,2 N·m (2.8 ­ 3.1 ft-lb) 7,6 ­ 8,4 N·m (5.6 ­ 6.2 ft-lb) 12,3 ­ 13,7 N·m (9.1 ­ 10.1 ft-lb) 20 ­ 22 N·m (14.7 ­ 16.2 ft-lb) 29,4 ­ 32,6 N·m (21.7 ­ 24.0 ft-lb) 57 ­ 63 N·m (42.0 ­ 46.5 ft-lb) 105 ­ 115 N·m (78 ­ 85 ft-lb) 160 ­ 180 N·m (118 ­ 133 ft-lb) 255 ­ 285 N·m (188 ­ 210 ft-lb) 345 ­ 385 N·m (255 ­ 285 ft-lb) 490 ­ 550 N·m (360 ­ 405 ft-lb) 660 ­ 740 N·m (490 ­ 545 ft-lb) 850 ­ 950 N·m (625 ­ 700 ft-lb) 1230 ­ 1370 N·m (900 ­ 1000 ft-lb) 1700 ­ 1900 N·m (1250 ­ 1400 ft-lb) 2300 ­ 2500 N·m (1700 ­ 1850 ft-lb) 2900 ­ 3200 N·m (2200 ­ 2400 ft-lb)

12.9 4,7 ­ 5,3 N·m (3.5 ­ 3.9 ft-lb) 8,5 ­ 9,5 N·m (6.2 ­ 7.0 ft-lb) 14,2 ­ 15,8 N·m (10.4 ­ 11.6 ft-lb) 23,7 ­ 26,3 N·m (17.5 ­ 19.5 ft-lb) 35 ­ 39 N·m (25.5 ­ 28.5 ft-lb) 71 ­ 79 N·m (52.5 ­ 58.5 ft-lb) 123 ­ 137 N·m (91 ­ 110 ft-lb) 190 ­ 210 N·m (140 ­ 155 ft-lb) 300 ­ 330 N·m (225 ­ 245 ft-lb) 420 ­ 460 N·m (310 ­ 340 ft-lb) 590 ­ 650 N·m (440 ­ 490 ft-lb) 800 ­ 880 N·m (590 ­ 650 ft-lb) 1000 ­ 1120 N·m (730 ­ 830 ft-lb) 1470 ­ 1630 N·m (1100 ­ 1200 ft- lb) 2000 ­ 2200 N·m (1500 ­ 1600 ft-lb) 2700 ­ 3100 N·m (2000 ­ 2300 ft-lb) 3500 ­ 3900 N·m (2600 ­ 2900 ft-lb)

24

ATTACHMENT / IMPLEMENT WARRANTY
A statement explaining the terms and conditions of the warranty coverage that applies to your attachment / implement is available by visiting Igniteattachments.com.

WARRANTY

25

, location……………………………………………………………3
A
approved models ……………………………………………… 11 attachment identification
concrete chute bucket ……………………………………….4 attachment storage ……………………………………………21
C
call before you dig ……………………………………………….5 chute extension
attaching ………………………………………………………..9 removing ………………………………………………………20 controls …………………………………………………………..15
D
daily inspection concrete chute bucket ……………………………………….9 machine quick coupler……………………………………….9
dimensions ………………………………………………………22
E
entering and exiting the machine ………………………….. 11
F
fastening to a trailer ……………………………………………19 fire prevention
electrical ………………………………………………………..6 fire extinguishers ……………………………………………..7 fueling …………………………………………………………… 7 hydraulic system………………………………………………6 flammable fluids ………………………………………………….6
G
grinding safety ……………………………………………………7
I
installing attachment non-powered machine quick coupler ………………….. 11 powered machine quick coupler …………………………13
L
lifting the attachment ………………………………………….18 loading ……………………………………………………………16
M
maintenance safety ……………………………………………..6

ALPHABETICAL INDEX
O
operating on slopes with empty attachment …………………………………….16 with full attachment …………………………………………15
P
publications and training resources………………………….8
R
removing attachment non-powered machine quick coupler …………………..17 powered machine quick coupler …………………………18
return to service ………………………………………………..21
S
safety rules ………………………………………………………..5 serial number……………………………………………………..3 silica dust exposure
avoiding …………………………………………………………6 spark arrester exhaust system safety……………………….7 specifications
torque for general metric bolts……………………………24 torque for general sae bolts ………………………………23 standard items ……………………………………………………4 starting safety …………………………………………………….7
T
troubleshooting chart ………………………………………….20
W
warranty ………………………………………………………….25 welding safety …………………………………………………….7

26

Reference Information Product Serial Number: Engine Serial Number: Dealer Information:
WARNING Cancer and Reproductive Harm. This product can expose you to chemicals including lead and lead compounds, mineral oils, and phthalates which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
2024 Ignite Attachments®. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>