ESC02
ELECTRIC SCOOTER
USER MANUAL

CAUTION: Please read the operating instructions before riding. Any child must be accompanied by an adult while using this scooter. In Australia, each state and territory has specific regulations that may apply to this product, including where you can legally use such products and if you need to register them with your local road traffic authority.  Please be sure to familiarise yourself with these prior to using this product.

PRODUCT OVERVIEW

| ACCESSORY/ PART| #| ACCESSORY/ PART

---|---|---|---
1| Accelerator| 7| Rear Mudflap
2| Control Panel| 8| Brake Light
3| Scooter Bell| 6| Disc Brake
4| Headlight| 10| Charging Port
5| Brake Lever| 11| Battery Compartment
6| Folding Mechanism| 12| Kickstand

CONTROL PANEL

The battery level is indicated by five power bars on the control panel. As the battery level is depleted these bars will turn off. Below the battery bars is the speed in km/h or MPH.
Battery level display
When the bottom battery bar flashes, it indicates the scooter has low power. If possible stop all use of the scooter and plug in the charger until the battery is fully charged. If the scooter does run out of power, all lights will turn off, and the scooter will coast until it comes to a complete stop.
Power button
Press and hold the power button for two seconds to turn on/off the scooter; After turning on, quickly press the power button twice to turn on/off the headlight; and quickly press three times to change the units between MPH and km/h.

WHAT’S IN THE BOX

ASSEMBLY AND SETUP

1. Fasten the handlebar stem on the base and put the kickstand down.

2. Attach the handlebar to the stem.

3. Tighten the screws onto both sides of the stem with the supplied Allen key.

4. When the assembly is complete, press the power button to ensure the scooter & control panel work correctly.

CHARGING YOUR SCOOTER

1. Lift up the rubber flap on the base of the scooter.
2. Plug the power adapter into the charging port.
3. When completed, remove the charger and cover it with the rubber flap.

FOLDING PROCEDURE

Turn the Scooter off, to fold up, unlock the folding clamp, and fold the handlebars back towards the rear mudguard. For ease of transport, once the Scooter is folded it can be carried by the handlebar stem.

SAFETY WARNINGS

1. In Australia, each state and territory has specific regulations that may apply to this product, including where you can legally use such products and if you need to register them with your local road traffic authority. Please be sure to familiarise yourself with these prior to using this product.
2. When operating this scooter, a helmet and other protective equipment are required.
3. This scooter is not engineered for skatepark or stunting use. Please keep both hands on the handlebars at all times.
4. This scooter is not designed to be used off-road. Only ride on flat and paved surfaces. Avoid riding on or through sand, gravel, mud, rugged or open ground. Do not ride on slippery surfaces, such as snow, ice or oil.
5. Do not use this scooter below -5°C or in wet conditions.
6. Before each use, ensure all bolts and screws are secure & tight.
7. Keep fingers, hairs, and clothing away from motors, wheels, and any moving parts.
8. Do not open or tamper with the frame or control panel as this will void the warranty.

This electric scooter is for private use only. When used in a public area, please follow the specific regulations for your state/territory.
This scooter has a top speed of 25km/h, please take into account stopping distances when traveling in public at these speeds. Please use caution when approaching pedestrians as a collision can cause serious injury to both the rider and pedestrian.
Check the scooter before each use. Upon inspection, if there are loose parts, low battery alerts, flat or excessive wear on the tires, or any other abnormal conditions, do not use the scooter and contact IGNITE customer support if required.
Aquila Group Pty Ltd. shall not be liable for any financial losses, physical injuries, accidents, legal disputes, and other interest conflicts resulting from actions that violate the user instruction manual.

CARE & MAINTENANCE

CLEANING & STORAGE
When not in use, store the scooter in a dry and cool location. Do not leave the scooter exposed to direct sunlight or in a damp/wet location. This can accelerate tyre aging, corrosion, or even compromise the battery pack.
To clean the scooter use a damp cloth and wipe away the dirt & debris. Ensure the power is turned off and the charging cable is unplugged with the rubber flap is securely closed to prevent any moisture from getting into the electronic components. Do not pressure wash the scooter as this will cause the electronic systems to fail. Alcohol, gasoline,
kerosene or other corrosive and volatile chemical solvents should also be avoided when cleaning the scooter.

BATTERY MAINTENANCE
Only original parts are permitted to be used in the scooter. Any third-party batteries or accessories can cause a failure & will void the warranty.
Do not store the scooter in a location where the ambient temperature is higher than 50°C or lower than -20°C, this includes leaving the scooter in a car under direct sunlight or for an extended time.
If the scooter is left for long periods of time between uses, it is recommended to fully charge the battery before the next use. Charging the battery before it is depleted can help prolong the life of the battery.
NOTE: Charging the battery takes ~5-6 hours. Each battery has a built-in chip that records a log of charging and discharging times. If the battery is left depleted for a prolonged period of time it will be unable to be recharged and not be covered by the standard warranty.

ADJUSTING THE DISC BRAKE
If the disc brake is too tight, use the supplied Allen key to loosen the screws on the caliper, and readjust the brake cable. Shortening the exposed cable will cause the brake to use less pressure. Lengthening the cable will cause the brake to become more responsive.

ADJUSTING THE HANDLEBARS
If the handlebars and stem sway during use, use provided Allen key to tighten the screws on the folding mechanism.

SPECIFICATIONS

[1] ITEM HEIGHT: from the ground to the top of the scooter;
[2] GENERAL RANGE: measured when it is no wind and at 30°C, the scooter’s fully charged to ride at an even speed of 20km/hon on a flat surface with a load of 165 pounds.
NOTE: data and specifications may vary due to different models, and are subject to change without notice.

IGNITE APP QUICK SETUP

Control your Electric Scooter using the IGNITE App.

1. Scan the QR code below or go to your phone’s App Store to download it.
2. Once downloaded, activate your Bluetooth, open the APP and pair your scooter.
3. When the scooter and phone are paired, the screen will show.

ESC02

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>